Instruction/ maintenance manual of the product IH60 Belling
Go to page of 23
Belling IH60 UK Part No 082749203 Date 19/03/2013 Users Guide & Installation Handbook.
CONTENTS & INTRODUCTION CONTENTS • SAFET Y • USING THE PRODUCT • CLEANING • INST ALL A TION INSTRUCTIONS • TECHNICAL DA T A • CUSTOMER CARE INTRODUCTION Thank you for buying this British- built appliance from us.
Safety 5.162 BEFORE USING THE PRODUCT Make sure that you ha ve removed all packaging and wrapping. Some of the items inside this appliance may have additional wrapping. GENERAL WARNING! - The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.
Safety 5.162 during use, as this will seriously affect the safet y and performance, particularly in relation to surface temper atures becoming hot and gas oper ated parts not workingefciently .The coolingfan(ift ted)is designed to run on after the control knob has been switched off .
Safety 5.162 electrical switch. Contact your local gas supplier immediately . ELECTRIC INDUCTION HOB WARNING:- Unattended cooking on a hob can be dangerous andmayresultinr e. NEVER try to extinguish arewithwater ,but switch off the appliance andthencoverame e.
Safety 5.162 fail-saf e. The pacemaker must be designed in compliance with the appropriate regulations. Caution: This appliance is for cooking purposes only .
Safety 5.162 the hob when you’re not around - take them of f the cook zone if you have to lea ve the kitchen even if you think it will only be for a moment, while you answer the door or phone.
Safety 5.162 distracted or leav e things unattended, so remember: If you’re called awa y from the cooker - by the phone or someone at the door , either take pans off the heat, or switch off y our hob. Don’t let yourself be distracted while cooking.
USING THE HOB - INDUCTION Before using your hob It is recommended that you clean and wash the hob surface bef ore using for the rsttime.Applyathincoatofceramic hob cleaner to the hob to maintain and protect it. See the customer care section for details of how to obtain all the av ail- able cleaning products.
USING THE HOB Central On/Off switch The central on/off switch enables all of the cooking zones to be switched off simultaneously at a touch of a key . To switch on the hob The hob is switched On by touching the“ON/OFF” key for 1 sec. A beep sounds and all the heater displays show a full stop in the cook zone display .
USING THE HOB Pan Detection As soon as you lift the pan off the zone the power is automatically reduced, help- ing to save energy . The above “U” symbol appears when a zone has been activated but .
USING THE HOB Induction Cook Zone Smallest Recom- mended Diameter (mm) LHF 150 LHR 120 RHR 150 RHF 120 Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolor ations on the ceramic glass surfacewhicharedifcultorimpossibleto remove.
USING THE HOB TROUBLESHOOTING The hob produces a smell the rst few times it is used Heat a pan full of water on each zone f or half an hour . Pans make a noise during cooking This is caused by vibration due to the pas- sage of energy from the hob to the pan.
USING THE HOB Appliance Errors Fault Description Action F0 Software Error Switch the power off and on, system should reset FA Safety key Error Switch the power off and on, system should reset FC Safet.
CLEANING ELECTRIC HOB Ceramic glass hobs • It is recommended that you clean and wash the hob surface bef ore usingforthersttime.Applyathin coat of ceramic hob cleaner to the hob to help maintain and protect it. • The ceramic hob top can be cleaned using a clean, damp cloth or kitchen paper .
installation General information Installation should only be carried out by aqualiedinstallerorengineer . Please keep to the following points most carefully; Although every care has bee.
installation CHOOSING YOUR INSTALLATION Make sure that the air inlets through the ventilator grids underneath the hob are never blocked. W e recommend that you install this ap- pliance in a work top which is a minimum 38mm deep.
installation Clearances and dimension – require- ments No shelf or overhang of combustible material should be closer than 650mm above the hob. There must be a minimum clearance of 50mm between the edges of the hob and any side walls; this clear ance must be maintained up to 420mm above the worktop.
installation Fitting into worktop Cut a hole in the work surface to the required size. A clearance of at least 50mm should be maintained between the cutout and any rear or side wall. The worktop must be of heat-resistant material or covered with heat -resistant material.
installation Fixing Bracket Advice Dealing with sides, cross-rails and back -panels in the cabinetry . Depending on the cabinets, the worktop thickness and the hob positioning, it is possible for the hob base and/or the clamp brackets to interf ere with parts of the cabinet.
installation Connect to the electricity supply (For Fixed Wiring only) WARNING: This appliance must be earthed. Only connect to the electrical mains terminal with the power switched off . The electrical mains terminal is live. Follow the terminal block connection schematic.
TECHNICAL DATA SINGLE PHASE SUPPLY: 230 -240V ~ 50Hz 6.6kW - 7.2kW 3 PHASE SUPPLY: 230 / 400V 3N ~ 50Hz Individual Cook Zone Power Ratings Cook Zone Normal Power/Boost Power Rating kW LHF 1.
CUSTOMER CARE 15.030 CUSTOMER CARE WEB SHOP Having purchased a superior cooker , hob or hood from us, you’ll naturally want to keep it looking great.
An important point after buying a device Belling IH60 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Belling IH60 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Belling IH60 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Belling IH60 you will learn all the available features of the product, as well as information on its operation. The information that you get Belling IH60 will certainly help you make a decision on the purchase.
If you already are a holder of Belling IH60, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Belling IH60.
However, one of the most important roles played by the user manual is to help in solving problems with Belling IH60. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Belling IH60 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
