Instruction/ maintenance manual of the product FGP300JN0 Whirlpool
Go to page of 9
Quic k Ref er ence T able of Cont ents: Pages 2 2 2 3 4 - 6 7 - 8 Installation Instr uctions IMPOR T ANT : Installer: Leave Installation Instructions with the homeowner. Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector's use.
Page 2 *** Note: 24" min. when bottom of wood or metal cabinet is protected by not less than 1/4" flame retardant mill- board covered with not less than No. 28 MSG sheet steel, 0.015" stainless steel, 0.024" aluminum or 0.020" copper.
Page 3 Gas supply r equir ements Observe all governing codes and ordinances. This installation must conform with all local codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.
Page 4 Installation st eps 1. Put on safety glasses and gloves. Do Not use oven door handle to lift or move the range. Pr epar ation A 2. Remove oven racks and parts package from inside oven. Remove shipping materials, tape and protective film from range.
Oper ating position C 5. Remove cardboard shipping base from under range. Open broiler door. Use a 3/8” drive ratchet to lower rear leveling legs one- half turn. Use channel lock pliers to lower front leveling legs one-half turn. 7. If installing the range in a mobile home, you MUST secure the range to the floor.
18 . Push in and turn each surface unit control knob to “LITE” position. The flame should light within 4 seconds. Turn control knob to desired setting after burner lights. Check each cooktop burner for proper flame. The small inner cone should have a very distinct blue flame 1/4" to 1/2" long.
Nat ur al g as con v ersion 1. Check that the manual shutoff valve in the gas supply line has been turned off. 2. Remove burner grates, burners and screws. Lift cooktop. Note: There is no cooktop support rod. Locate pressure regulator. DO NOT REMOVE THE PRESSURE REGULATOR.
Page 8 6. Oven burner: Use 1/2" combination wrench to loosen the orifice hood away from the pin (approximately 2 to 2-1/2 turns). The burner flame cannot be properly adjusted if this conversion is not made. 7. Locate selector key on oven thermostat and turn counterclockwise to the Natural position.
If r ang e does not oper ate: Check that gas line is turned on. See Use and Care Guide for troubleshooting list. If y ou need assistance: If you have questions about operating, cleaning or maintaining your range: Refer to Use and Care Guide.
An important point after buying a device Whirlpool FGP300JN0 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Whirlpool FGP300JN0 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Whirlpool FGP300JN0 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Whirlpool FGP300JN0 you will learn all the available features of the product, as well as information on its operation. The information that you get Whirlpool FGP300JN0 will certainly help you make a decision on the purchase.
If you already are a holder of Whirlpool FGP300JN0, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Whirlpool FGP300JN0.
However, one of the most important roles played by the user manual is to help in solving problems with Whirlpool FGP300JN0. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Whirlpool FGP300JN0 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
