Instruction/ maintenance manual of the product ECKMF-28 Whirlpool
Go to page of 8
TKirlpool CORPORATION ECKMF-28 HOW TO INSTALL YOUR AUTOMATIC ICE MAKER USE THESE INSTRUCTIONS ONLY FOR 28 INCH TOP FREEZER REFRIGERATORS Part No 939024 A.
THE PARTS IN THIS KIT ARE USED FOR MORE THAN ONE MODEL KEEPALL PARTS IN THEIR WVN PACKAGE UNTIL USED. Parts are listed in order of usage. Arrange in order before starting installation.
A. CONNECTING ICE MAKER TO FREEZER Al. Put tubing (#836240) in pan of hot tap water to soften it. This will make it easier to install. ‘NOTE: CLIPS SHOULD STAY UPRIGHT UNTIL ICE MAKER IS IN PLACE ON SHIELD. (STEP Al 1) STEP A3&STEP A4 1 STEP A5 TUBE COVER I NOTE: CREEL’ EQy’TPED FoR I WIRE MUST BE AUlOMATIC ON TOP ICE MAKER I A2.
NOTE. GREEN WIRE MUST BE STEP A10 AlO. Connect Ice Maker to wiring assembly. Place the ice maker on the side of the freezer so: 1. Wiring lays between shield and Ice Maker. 2. Plug is flat against the shield. 3. Wiring is above the bracket on the back of Ice Maker.
83. Remove the metal junction box and save the 2 mounting screws. a. Bend back ears of 3 wire plug on ice maker wiring assembly. b. With the green wire up, snap the plug into hole in side of junction box. c. Connect the 3 wire plug into mating part in junction box.
C. INSTALLING WATER VALVE ON LO WER BACKOF CABINET LEG. STEP Cl ,U6?6074 WASHER TUBING Cl. Plug wiring assembly into water valve so that the two parts fit together tightly. C2. Fasten water valve to cabinet leg with 1 screw (#488649). w Ii49 C3. Attach valve ground wire to cabinet with ground screw (#488500).
D. CONNECTING ICE MAKER TO WATER SUPPLY You will need enough %-inch O.D. copper tubing to connect refrigerator to water source and two 6” or 8” adjustable or open end wrenches. TYPICAL WAYS TO CONNECT TO WATER SUPPLY Through floor to basement cold water pipe.
Dl. Find a %-inch to l-inch vertical COLD water pipe near the refrigerator. (Horizontal pipe will work but extra precaubons must be taken.) D2. Measure from inlet on rear of refrigerator to water pipe. Add 7 feet to allow for moving re- frigerator for cleaning.
An important point after buying a device Whirlpool ECKMF-28 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Whirlpool ECKMF-28 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Whirlpool ECKMF-28 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Whirlpool ECKMF-28 you will learn all the available features of the product, as well as information on its operation. The information that you get Whirlpool ECKMF-28 will certainly help you make a decision on the purchase.
If you already are a holder of Whirlpool ECKMF-28, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Whirlpool ECKMF-28.
However, one of the most important roles played by the user manual is to help in solving problems with Whirlpool ECKMF-28. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Whirlpool ECKMF-28 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
