Instruction/ maintenance manual of the product 9200 SERIES Whirlpool
Go to page of 24
Upper spray arm Bonom rack Rack bumper Heating &amen Sllverware bas Lower spray arm I I Model and Access serial number I Door color panel panel label (on right side) 9200 SERIES DISH WASHERS.
Contents Page Important Safety Instructions ....... Operating Instructions .............. Using your dishwasher for the first time . Before starting your dishwasher ....... Starting your dishwasher ....... . ...... Changing a cycle setting ...........
Important Safety Instructions l Read all instructions before using l DO NOT wash plastic items unless marked the dishwasher. “Dishwasher Safe” or the equrvalent. If not l Properly connect to electricity and water. marked, check manufacturer’s l DISHWASHER MUST BE ELECTRICALLY recommendations.
Operating Instructions Continued Control pads Starting your dishwasher 1. Press the START pad once to display the cycle and options. Skip to Step 4 if you want lo run the cycle and options shown by the lights. 2. Press the CYCLE pad until the cycle you want is indicated by a srgnal light.
Delaying a wash The DELAY pad allows you to delay the start of a cycle for 2 hours after loading the dishwasher. For example, use the DELAY to run the dishwasher during off-peak hours of electrical use. 1. Press the DELAY pad once to display the last cycle and options, selection.
Operating Instructions Continued Control panel lock-out feature This feature lets you lock-out the function of the control pads (except to cancel or pause a cycle that is running). When the control panel is locked- out, the dishwasher cannot be started and a running cycle cannot be changed.
The WATER HEATING signal light The WATER HEATING signal light comes on during the water heating portions of the Pots 8 Pans Cycle. The signal light will also come on during the water heating portion of other cycles when the Hi-Temp Option is selected.
What happens in each cycle Pots 8 Pans Cycle A double wash with maximum cleaning for cooked-on or baked-on foods. Cycle time’ is about 73 minutes plus the time needed while the timer delays to heat the water (marked t) to 140°F (60%) in both washes and the last rinse.
Normal Cycle A single wash for normal, everyday soiled loads. (The Energy Guide Label is based on this cycle.) Cycle time’ is about 66 minutes plus the time needed while the timer delays to heat the water to 140°F (60%) in the wash (marked t) and, if the Hi-Temp Option is selected, in the final rinse (marked tt).
Operating Instructions Continued Rinse 8 Hold Cycle For rinsing a few items to be washed one or more days later. Cycle time is about 12 minutes. 10 I Rinse I I Rinse I I 1 What happens in each option Options can be selected by pressing the OPTIONS pad.
Proper Loading Cup and glass load Preparation for loading It is not necessary to rinse dishes before putting them into the dishwasher. Just remove large pieces, bones and other hard items. The POWER CLEAN’” Module will remove food particles from the water.
Proper Loading Continued 1 Lower Mixed load =v Adjustable top rack The top rack does not have to be level. l Raise or lower one or both sides to help fit tall items in the top or bottom rack. l Turn knob clockwise to raise a side. l Turn knob counterclockwise to lower a side.
Silverware basket loading Load forks and spoons so lhey don’t nest together. Spray can’t reach nested items. Mix items in each section of the basket.
Adding Detergent Liquid dlshwasher detergent See phosphorus content on product labels. Cover Cover Latch What kind of detergent to use Use automatic dishwasher detergent only. Other detergents are too mild and much too sudsy to work in the dishwasher.
Using Rinse Agent Dispenser Rinse agent dispenser Keep the rinse agent dispenser filled with a liquid rinse agent such as Jet-Drys A rinse agent greatly improves the drying of dishes by helping water flow off of them during the last rinse. A rinse agent also keeps water from forming droplets and drying as spots.
For Best Results Hot water is a must Hot water dissolves and activates the dishwashing detergent. Hot water dissolves grease on dishes and helps dry glasses spot-free. Make certain loads are washed in hot water. Two ways to have a reliable hot water supply.
Energy saving tips You can help save energy if you: 1. Wash full loads. Running a half-filled dish- washer uses the same amount of electricity and hot water as a fully loaded machine. 2. Use the Low Energy Cycle whenever possible. It uses less hot water and energy than other cycles.
Common Dishwashing Problems Spotting and filming (hard water film) Hard water Fill detergent dispensers to capacity. Use dishwasher detergent with highest available phosphorus content. May be necessary to install water softener. To remove spots and film, try a vinegar rinse.
Dishes not washing clean Water is not hot enough Water temperature should be at least 140°F (SOOC). Set water heater thermostat to a higher setting. Run water at sink until hot before starting and/or use Hi-Temp Option. Improper loading Make sure dishes and glassware are loaded so spray reaches all surfaces and items drain properly.
If You Need Service Or Assistance We suggest you follow these steps: 1. Before calling for assistance,. Performance problems often result from little things you can find and fix yourself without tools of any kind.
3. If you need service’... Whirlpool has a nationwide 2 network of authorized TK+l oly WhirlpoolsM service com- SERv,cE panies. Whirlpool service technicians are trained to fulfill the product warranty and provide after-warranty service, anywhere in the United States.
Notes 22.
POWER CLEAN’” washing system parts covered by your warranty rh spray arm ‘Spray tower N0ZZle cap CLEAN and motor.
I- WHIRLPOOL” Dishwasher Warranty DW017 LENGTH OF WARRANTY WHIRLPOOL WILL PAY FOR FSPs replacemenl pans and repair labor to correcl defects in materials or workmanshio.
An important point after buying a device Whirlpool 9200 SERIES (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Whirlpool 9200 SERIES yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Whirlpool 9200 SERIES - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Whirlpool 9200 SERIES you will learn all the available features of the product, as well as information on its operation. The information that you get Whirlpool 9200 SERIES will certainly help you make a decision on the purchase.
If you already are a holder of Whirlpool 9200 SERIES, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Whirlpool 9200 SERIES.
However, one of the most important roles played by the user manual is to help in solving problems with Whirlpool 9200 SERIES. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Whirlpool 9200 SERIES along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
