Instruction/ maintenance manual of the product 8524511 Whirlpool
Go to page of 15
Part No. 8524511 Pieza No. 8524511 N° de pièce 8524511 Models dimension A Modelos dimensión A Modèles dimension A Whirlpool 25" (63.5 cm) Printed in U.
Introduction Introducción Introduction Y ou need to: ✔ carefully open dishwasher door while someone grasps the rear of the dishwasher . Remove shipping materials, drain hose and lower rack. Close dishwasher door . Latch the dishwasher door shut. ✔ observe all governing codes and ordinances.
4 Cabinet opening Requirements Requisitos Spécifications Check location where dishwasher will be installed. The location must provide: ✔ easy access to water , electricity and drain. ✔ convenient loading. Corner locations require a 2" (5.1cm) minimum clearance between the side of the dishwasher door and wall or cabinet.
Y ou must have: ✔ 120-volt, 60-Hz, AC-only , 15- or 20-amp., fused electrical supply . ✔ COPPER WIRE ONL Y . Il vous faut : ✔ un cir cuit d’alimentation de 120 volts (CA seulement), 60 Hz, 15 ou 20 A, avec fusible. ✔ FIL DE CUIVRE SEULEMENT .
9" (22.9 cm) 10" (25.4 cm) 5-1/2" (14 cm) 6" *** (15.2 cm) 6" *** (15.2 cm) 3-1/4" (8.3 cm) 2-3/4" (7 cm) * Measured from the lowest point on the underside of countertop. May be reduced to 33-7/8" (86 cm) by removing wheels from dishwasher .
10 continued from page 8 suite de la page 8 viene de la página 8 4. Run wire into house wiring junction box. Use strain relief method provided with junction box. If no strain relief is provided, install a U.L.-listed/CSA- certified clamp connector for flexible- type wire.
11a. continued from page 10 suite de la page 10 viene de la página 10 1. Remove the disposer knockout plug. Cut end of drain hose if needed (do not cut ribbed section). 2. Attach drain hose to air gap with large spring-type clamp . If the drain hose was cut, use a 1-1/2" to 2" (3.
4. Remove terminal box cover . Pull appliance wires through hole in terminal box. Do not untie the knot in the wires. Ôter le couvercle de la boîte de connexion. Faire passer les fils de l’appareil dans le trou de la boîte de connexion.
16 6. 7. 9. 10. Stand dishwasher upright. The dishwasher must be secured to the cabinet. There are two brackets on top of the dishwasher that usually can be attached to the countertop. If this is not possible, the brackets may be moved to the sides of the dishwasher .
18 17 T o adjust the door spring tension, unhook the spring from the rear leg of dishwasher . With a 5/16" nut driver or hex socket, remove the screw from the tensioner . The screw can be put into one of three holes , , in front leg of dishwasher .
HELPFUL TIP: • Select the proper size twist-on connectors to connect your household wiring to 16-gauge dishwasher wiring. • Inser t wire ends into twist-on connector . Do not pre-twist bare wire. • T wist connector . • Gently tug on wires to be sure both are secured.
T erminal box wire: white black ground connector Power supply wire: white black grounding wire Fil de la boîte de connexion : blanc noir connecteur de liaison à la terre Fil d’alimentation de cour.
24 Push the drain hose into the connector up to the rib on the drain hose. Pousser le tuyau de vidange dans le connecteur jusqu’à la nervure sur le tuyau de vidange Inserte la manguera de desagüe en el conector hasta la nervadura en la manguera de desagüe.
26 E. Check Operation Vérification du fonctionnement V erifique el funcionamiento 3. 4. 1. 2. 3. 4. Secure dishwasher to countertop or sides of cabinet with two, No. 10 x 1/2" Phillips-head screws . The dishwasher MUST be secured to keep it from tipping when door is opened.
Part No. 8524511 Pieza No. 8524511 N° de pièce 8524511 Models dimension A Modelos dimensión A Modèles dimension A Whirlpool 25" (63.5 cm) Printed in U.
An important point after buying a device Whirlpool 8524511 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Whirlpool 8524511 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Whirlpool 8524511 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Whirlpool 8524511 you will learn all the available features of the product, as well as information on its operation. The information that you get Whirlpool 8524511 will certainly help you make a decision on the purchase.
If you already are a holder of Whirlpool 8524511, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Whirlpool 8524511.
However, one of the most important roles played by the user manual is to help in solving problems with Whirlpool 8524511. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Whirlpool 8524511 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
