Instruction/ maintenance manual of the product 801 Whirlpool
Go to page of 25
Undercounter Dishwasher Power cord models Part No. 3369689 IMPORTANT: Read and save these instructions. IMPORTANT: tnskdter: Leave Installation Instructions with homeowner. . . Homeowner: Keep Installation Instructions for future reference. Save kxtallation Instructions for local electrical inspector’s use.
Before you start... Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. Keep cardboard shlpplng base or plywood under dlshwasher until It ls Installed, or slide dlshwasher onto cardboard or hardboard betore movlng It across the tloor.
Built-in opening reaujrrements Electrical Shock Hazard Electrical wiring, water supply line, and drain line must not contact any exposed terminals of the dishwasher wiring. Cabinet opening must completely enclose sides, top and back of dishwasher. Failure to follow these instructions can result in death or electrical shock.
Electrical requirements Electrical Shock Hazard Electrically ground dishwasher. Connect grounding wire to green grounding nut in terminal box. Do Not ground to a gas supply pipe. Do Not connect dishwasher to electrical supply until appliance is permanently grounded.
Water requirements All solder connectlons must be made before the wafer line Is connected to the dlshwasher to prevent damage to Inlet valve. Do Not solder wlthln 6 Inches (15 cm) of the Inlet valve. The plastic part of the Inlet valve could be damaged.
Drain requirements The drain hose must connect to the house plumblng at a mlnlmum of 20 Inches (50.8 cm) above the floor. Thls will prevent backflow or water slphonlng out of dlshwasher durlng operatlon. If the draln hose Is routed to a connectlon point less than 20 Inches (50.
Alternate methods: wpw to fit. clearance to floor If local plumbing codes permit, dishwasher drain hose may be connected directly to waste tee. The waste tee connection MUST be made ahead of the 1 k%c$$%?$~~kk%~e connector. clearance to above trap. floor If local plumbing codes permit, dishwasher drain hose may be connected directly to disposer.
4 w Check that front leveling legs are firmly against the floor. Align dishwasher door with cabinet doors, so that spacing is the same on both sides. Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts.
Numbers correspond to installation steps. drain hose Cut here to Connect to connect to garbage waste tee or disposer connector. 12 m Make electrical connection. CHECK ELECTRICAL REQUIREMENTS. BE SURE YOU HAVE THE CORRECT ELECTRICAL SUPPLY AND RECOMMENDED GROUNDING METHOD.
control console console, allowing panel(s) to rest on bottom of door. Push in along 6 n Snap one end of retainer into channel as shown. Push inward while sliding thumb along full length of retainer. To change access colour panel (For models so equipped) Injury Hazard Wear gloves and handle panels carefully.
Custom panel dimensions Note: This panel is narrower than access panel. File or sand edges of wood panel to avoid slivers. door panel side view top edge 7132” (0.56 cm) edge door panel front view L23” (58.4 cm)& access panel - 23-5/16” (59.2 cm) -7 Routing custom panels clear access when door is 7132” top view (0.
ins be sid panel fits betwe& 5 not inside, door frame n Insert top of wood door panel between sides of door frame about 3” (7.5 cm) below console. Rotate wood door panel down against dishwasher door. Slide top edge of wood door panel under bottom edge of console.
Lavewaisselle encast& Mod&k 6 cdblage direct Pike N” 3369689 IMPORTANT: Lire et conserver ces instructions. IMPORTANT : lnstallateur - Remet-he les instructions d’instatlation au proprihire. Proprihtaire -Conserver les instructions d’installation pour rkfkrence ukrieure.
Avant de commencer.. . Risque de basculement Ne pas utiliser le law-vaisselle avant que I’installation soit compl&tement termike. Ne pas appuyer sur la Porte ouverte.
Spkificatfons de I’ouverture Le cablage electrique, les canalisations d’eau et les canalisations d’evacuation ne doivent pas entrer en contact avec des bouts exposes du ceblage du lave-vaisselle. L’encastrement de I’appareil dans le placard doit recouvrir completement les &es, le sommet et I’arribre du lave- vaisselle.
Le non-respect de cette instruction peut 6tre la cause d’un incendie ou d’un choc klectrique, ou mQme d’un accident mortel. Risque de choc Blectrique Relier 6lectriquement le lave- vaisselle B la terre. Connecter le fil de liaison & la terre ti l’kcrou vert de liaison B la terre dans la boRe de connexion.
AlSmentation en eau Pour que la valve d’entr6e d’eau ne sublsse pas de dommages, II faut que tous les raccordements par soudure solent exkut& avant que la canallsatlon d’arrlvbe d’eau solt rell6e au lave-valsselle. Ne pas souder 6 molns de 15 cm (6 po) de la valve d’eau.
Rejet 21 I’6gout Raccordement A I’bgout La canallsatlon au rkeau de plomberle de la ksldence dolt Btre sltuOe b au molns 50,8 cm (20 po) au-dessus du sol.
Autres methodes: hauteur mlnlmale de Ld pint d’entke dolt 50,s cm (20 po) 4tre au-dessus du au-dews du nlveau du pl‘ e du sol slphon de dec *“il arge. Si les codes locaux le permettent, on peut raccorder le tuyau de decharge du lave- vaisselle directement a un raccord T d’evacuation.
tableau. A I’aide d’un niveau, contrdler I’horizontalit6 du lave- vaisselle, dans le sens avant/arri&e. Pour empkher les dommages au plancher dkplacer le lave-vaisselle sur le plancher, et I’incliner vers I’arrkre sur ses roulettes.
Les chlffres correspondent aux &apes. Tuyau de dkharge plac6 B l’lntbteur de la cuve lors de la Ilvralson. Porte. panlers, panneau d’acc& et Danneau avant non’lllustr&. Extr6mlt6 b connecter au raccord Tuyau de d&charge pIa& 5 I’lnt6rleur de la cuve 101s de la Ilvralson.
2 n Soulever chaque ext+mit& du panneau de Porte. A I’aide d’une main, cintrer le panneau infbrieur. Enlever le panneau. Ne pas enlever la plaque d’espacement. 3 w lns&er un c6t6 du panneau de Porte dans I’encadrement de la Porte, la couleur d&.
celle du grain des portes des placards. l Limer et poncer les bords des panneaux en bois. l Le lave-vaisselle est source d’humidite. Appliquer un bouche-pores resistant a I’humidite sur les deux faces et sur les bords des panneaux en bois. * tpaisseur reelle de 0.
Installation des panneaux en bofs personnahis - Porte et ouverture d’accks 1 w Decouper les panneaux de bois de la Porte et de I’ouverture d’acces selon les dimensions specifiees, de telle maniere que I’orientation du grain du bois corresponde a celle du placard.
9 n Faire glisser prudemment le panneau colorG vers le haut pour le retirer. Conserver le panneau colore et la plaque d’espacement pour reutilisation ulterieure. 10 n lnserer le panneau en bois dans I’encadrement du panneau de I’ouverture d’acces.
An important point after buying a device Whirlpool 801 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Whirlpool 801 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Whirlpool 801 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Whirlpool 801 you will learn all the available features of the product, as well as information on its operation. The information that you get Whirlpool 801 will certainly help you make a decision on the purchase.
If you already are a holder of Whirlpool 801, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Whirlpool 801.
However, one of the most important roles played by the user manual is to help in solving problems with Whirlpool 801. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Whirlpool 801 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
