Instruction/ maintenance manual of the product 2180913 Whirlpool
Go to page of 18
Installation Changing The Bin Door And Lower Panels 2 General Information 3 For The Plumber 4 For The Electrician 6 How The Ice Maker Works 7 Things To Remember 7 Operating Instructions 8 Unit Wiring Diagrams 8 Check Operation 9 AUTOMATIC ICE MAKER Part No.
Changing The Bin Door And Lower Panels The storage bin door is designed to accept an optional decorative wood panel of your choice. The wood panel should be no more than l/4 inch (6 mm) thick. Cut it to the same size as the production metal panel. To change the bin door panel: I.
General Information Unpack 1. Lay carton on rear face and break open bottom flaps. 2. Set carton upright with all four flaps outward. 3. Lift carton up and off of machine. 4. Remove all tape and packaging materials from the outside and inside of the cabinet.
Level unit 1. After placing unit in position, check to make 4. If you are installing this ice maker in a certain the unit is level side-to-side and commercial setting that requires National front-to-back. Sanitation Foundation (NSF) installation 2. Accurate leveling is essential for proper procedures, NSF requires that the ice operation.
Connect to drain (observe local codes) 1. The unit is provided with a gravity drain. 2. The ideal installation has a standpipe (1 -l/4” [32 mm] minimum) installed directly below the outlet of the drain tube. Refer to figures for the proper location of the standpipe.
For The Electrician Electrical1 requirements A 115 Volt, 60 Hz., AC only, 15 or 20 ampere electrical supply circuit, properly grounded in accordance with the National Electrical Code and local codes and ordinances is required. It is recommended that a separate circuit, serving only this appliance, be provided.
How The Ice Maker Works l Compressor runs . Condenser fan runs l Water pump runs (circulates water) l Cutter grid is warm to touch WHEN THE DESIRED ICE SLAB THICK- NESS IS REACHED, THE HARVEST CYCLE BEGINS AND THE FOLLOWING HAPPENS: l Evaporator thermostat is satisfied .
Operating Instructions l For complete operation information, refer to the Use and Care Guide. l Before starting, wash out interior of cabinet with a Baking Soda solution (2 tablespoons [26 grams] soda to 1 quart [l liter] of warm water). Rinse thoroughly.
Check Operation Start the unit by turning the service switch to “ON” and opening the line d water valve. NOTE: Left is “OFF” - Middle is “ON” - Right is “CLEAN.” In “CLEAN” position, only the pump operates. Check condenser fan to make sure it is revolving.
d’installation Changement du panneau de la Porte du receptacle et du panneau inferieur Renseignements generaux Instructions a I’intention du plombier Instructions a I’intention de I’electricie.
Changement du panneau de la Porte du rkeptacle et du panneau inferietir La Porte du rkeptacle 2 glaGons peut recevoir un panneau dkcoratif en bois (facultatif) choisi par I’utilisateur. L’Bpaisseur du panneau en bois ne doit pas dbpasser 6 mm (‘I4 PO).
Renseianements cwh6raux - Dbballage 1. Placer la boite en appui sur la face arriere, et ouvrir les rabats du fond. 2. Placer la boite verticalement, en veillant a ecarter les rabats. 3. Soulever la boite en carton pour degager la machine. 4. Retirer tous les rubans adhesifs et materiaux d’emballage a I’exterieur et a I’interieur de la caisse.
Mise d’aplomb 1. Apres avoir place I‘appareil a l’emplacement 4. Si cette machine a glacons doit etre utilisee d’installation, controler I’aplomb, lateralement dans une application commerciale assujettie et d’avant en arriere. aux normes de la National Sanitation Founda- 2.
Raccordement B I’hgout (observer les dispositions des codes loeaux) 1. L’appareil est dote d’un systeme de d&charge a l’egout, par gravite. 2. L’installation ideale comporte un tuyau d’evacuation (minimum 32 mm [I % PO]) installe directement au-dessous de I‘orifice de decharge du tube de decharge.
Instructions & I’intention de Wlectricien Spkifications de I’alimentation klectrique Cet appareil doit etre alimente par un circuit de On recommande I’emploi d’un circuit 115 volts, 60 Hz. CA seulement, 15 ou 20 d’alimentation independant, ne desservant que amperes, convenablement relic ti la terre cet appareil.
Mode de fonctionnement 0 Compresseur en marche 9 Ventilateur du condenseur en marche * Pompe B eau en rrarche (circulation de I’eau) l Grille de decoupage tiede au toucher LORSQUE L’CPAISSEUR Dl%I.
Instructions d’utilisation . Au sujet des instructions detaillees, voir le Guide d’utilisation et d’entretien. l Avant la mise en marche de I’appareil, laver les surfaces interieures avec une solution de bicarbonate de sodium (26 g [2 c. a soupe] de bicarbonate dans 1 litre [l pinte] d’eau tiede).
Contr6le du fonctionnement Pour la mise en marche de I’appareil. placer le commutateur a la position de MARCHE d (ON) et ouvrir le robinet d’arrivee d’eau. REMARUUE : Position de gauche OFF = ARRET, position mediane ON = MARCHE, position de droite CLEAN = NETTOYAGE.
An important point after buying a device Whirlpool 2180913 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Whirlpool 2180913 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Whirlpool 2180913 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Whirlpool 2180913 you will learn all the available features of the product, as well as information on its operation. The information that you get Whirlpool 2180913 will certainly help you make a decision on the purchase.
If you already are a holder of Whirlpool 2180913, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Whirlpool 2180913.
However, one of the most important roles played by the user manual is to help in solving problems with Whirlpool 2180913. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Whirlpool 2180913 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
