Instruction/ maintenance manual of the product WESY39200 Weider
Go to page of 33
USER'S MANUAL QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through assistance from our factory . TO A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR T OLL-FREE CUSTOMER HOT LINE.
2 T ABLE OF CONTENTS LIMITED W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 W ARNING: T o reduce the risk of serious injury , read the following important precautions before using the home gym system. 1. It is the responsibility of the owner to ensure that all users of the home gym system are adequately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 76 in. Width: 89 in. Length: 64 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms W arning Decal No.
5 ASSEMBL Y 1 8 11 51 27 1 4 3 1 51 5 1. Before beginning assembly , be sure that you have read and understand the infor- mation in the box above. Locate and open the parts bag labeled ÒFRAME ASSEMBL Y .Ó Press two 2Ó Square Outer Caps (51) onto the indicated locations on the Stabilizer (5).
6 2. Slide the Rear Upright (74) and the Leg Press Upright (56) onto the indicated 5/16Ó x 2 1/2Ó Carriage Bolts (1) in the Stabilizer (5). The high side of the brackets on the Rear Upright and Leg Press Upright should be on the side shown. Hand tighten four 5/16Ó Nylon Locknuts (3) onto the Carriage Bolts.
7 4. Press a 2Ó Square Inner Cap (27) into the end of the T op Frame (55). Press a 1 3/4Ó Square Inner Cap (44) into each end of the crossbar on the T op Frame.
8 7. Press a Weight T ube Bumper (64) into the end of a Weight T ube (63). Insert the Weight T ube into the front stack of Weights (25). Be sure that the pin on the Weight T ube is sit- ting in the pin grooves in the top Weight. Lubricate the inside of the holes in the T op Weight (65).
9 9. Attach the upper ends of the Short Weight Guides (73) to the T op Frame (55) with a 5/16Ó x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers (61), and a 5/16Ó Nylon Locknut (3). Attach the upper ends of the Long Weight Guides (62) to the T op Frame (55) with a 5/16Ó x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers (61), and a 5/16Ó Nylon Locknut (3).
10 12. Press a 1Ó Round Inner Cap (49) into one of the Press Arms (46). Press a 1 3/4Ó Square Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16Ó x 2 1/2Ó Bolts (22) and two 5/16Ó Nylon Locknuts (3).
11 15. See the inset drawing. Attach the Military Press Arm (84) to the Pivot Arm (80) with two 5/16Ó x 2 1/4Ó Bolts (33) and two 5/16Ó Nylon Locknuts (3). Press two 1 1/2Ó Square Inner Caps (32) into the indicated end of the Military Press Arm (84).
12 18. Wrap the High Cable (58) around a ÒVÓ-Pulley (50). Attach the ÒVÓ-Pulley and a Long Cable T rap (31) to the indicated bracket on the Front Upright (42) with a 3/8Ó x 2 1/2Ó Bolt (86) and a 3/8Ó Nylon Locknut (21). Be sure that the Long Cable T rap is positioned to hold the Cable in place.
13 22. See the inset drawing. Attach a 3 1/2Ó Pulley (15) and a Cable T rap (66) to the upper hole in a Long ÒUÓ-Bracket (57) with a 3/8Ó x 2Ó Bolt (12) and a 3/8Ó Nylon Locknut (21). Be sure that the Cable T rap is inside the Long ÒUÓ- Bracket.
14 25. Locate the Low Cable (23) and the bag labeled ÒLOW PULLEY .Ó Route the Low Cable under the 3 1/2Ó Low Pulley (76). Attach the Pulley and the 5/8Ó x 9/16Ó Spacer (7) to the Press Frame (17) with a 3/8Ó x 3 3/4Ó Bolt (88), 3/8Ó Flat W asher (9), and a 3/8Ó Nylon Locknut (21).
15 29. Attach the end of the Low Cable (23) to the Long ÒUÓ-Bracket (57) with a 1/4Ó Nylon Locknut (2) and a 1/4Ó Flat W asher (10). Y ou may need to lift the T op Weight (not shown) on the High Cable to get enough slack to attach the Low Cable to the Long ÒUÓ-Bracket.
16 32. Wrap the Military Press Cable (72) around a 3 1/2Ó Pulley (15). Attach the Pulley and a Cable T rap (66) to the Pivot Arm (80) with the 3/8Ó x 5Ó Bolt (101). Be sure the Bolt is on the side shown, and that the Cable T rap is positioned to hold the Cable in place.
17 CABLE ASSEMBL Y 35. Locate the Leg Press Cable (78). Attach the end of the Leg Press Cable to the Long ÒUÓ- Bracket (57) with a 1/4Ó Nylon Locknut (2) and a 1/4Ó Flat W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing.
18 39. Attach the Front Backrest (41) to the Front Upright (42) with two 1/4Ó x 2 1/2Ó Screws (43) and two 1/4Ó Flat W ashers (10). 40. Press a 1 1/2Ó Square Inner Cap (32) into the Front Seat Frame (36). Insert a 1/4Ó x 2Ó Carriage Bolt (38) through the center hole in the Seat Plate (37).
19 SEA T ASSEMBL Y 43. Press two 3/4Ó Round Inner Caps (34) into each Pad T ube (28). Insert a Pad T ube (28) into the Front Seat Frame (36). Slide a Foam Pad (30) onto each end of the Pad T ube. Insert the other Pad T ube (28) into the Leg Lever (29).
20 SEA T ASSEMBL Y 44. Remove the adhesive backing from the CLUB WEIDER ¨ 16.4ST decal and apply it to the Front Upright (42) under the ÒWEIDERÓ nameplate as shown. 45. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in HOW T O USE THE HOME GYM SYSTEM, beginning on page 21 of this manual.
21 HOW T O USE THE HOME GYM SYSTEM The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise.
22 A TT ACHING AND REMOVING THE SEA T T o attach the Seat (13), set the bracket on the Front Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Seat Frame to the Front Upright with the 5/16Ó x 2 3/4Ó Carriage Bolt (14), 3/16Ó Flat W asher (8) and the Seat Knob (40).
23 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. ÒT opÓ refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
24 TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately . The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent.
25 CABLE DIAGRAMS The cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), the Military Press Cable (72), and the Leg Press Cable (78). Use the diagrams to be sure that the four cables and the cable traps have been assembled correctly .
26 Military Press Cable (72) Leg Press Cable (78) Rear Weight StackÑ 1 2 3 4 6 5 7 8 Ball End 3 2 4 Ñ Rear Seat Frame 1 Ñ Long ÒUÓ-Bracket Military Press Cable (72) and Leg Press Cable (78).
27 NOTES.
5/16" Nylon Locknut (3) 1/4" Flat W asher (10) 5/16" Flat W asher (8) 3/8" Flat W asher (9) 1/4" x 2 1/2" Screw (43) 3/8" Nylon Locknut (21) 1/4" x 2" Mach.
1" Retainer (69) 3/8" x 3 1/2" Bolt (16) 1/4" x 3/4" Screw (18) 5/16" x 5" Bolt (68) 3/8" x 3 3/4" Bolt (88) 3/8" x 8" Bolt (59) Cable Clip (53) .
1" Round Inner Cap (49) 1" Round Cover Cap (70) 3/4" Round Inner Cap (34) 1/2" x 3/4" Spacer (61) 5/16" x 2" Eyebolt (35) 1 1/2" Square Inner Cap (32) 1 3/4&quo.
P ART LISTÑModel No. WESY39200 R0900A Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
60 27 21 15 55 12 11 8 15 12 44 88 15 58 21 44 21 3 61 62 24 3 58 71 2 65 63 64 25 26 19 21 9 3 3 49 6 22 46 46 16 3 9 15 21 59 23 21 17 27 1 4 10 43 41 42 21 3 50 31 86 70 69 69 70 21 47 44 45 44 45 .
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
An important point after buying a device Weider WESY39200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Weider WESY39200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Weider WESY39200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Weider WESY39200 you will learn all the available features of the product, as well as information on its operation. The information that you get Weider WESY39200 will certainly help you make a decision on the purchase.
If you already are a holder of Weider WESY39200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Weider WESY39200.
However, one of the most important roles played by the user manual is to help in solving problems with Weider WESY39200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Weider WESY39200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
