Instruction/ maintenance manual of the product WESY38322 Weider
Go to page of 33
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if parts are missing, we will guarantee com- plete satisfaction through assis- tance from our factory . TO A VOID DELA YS, PLEASE CALL DIRECT T O OUR TOLL- FREE CUSTOMER HOT LINE.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORT ANT PRECAUTIONS 3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 77 in. Width: 81 in. Length: 59 in. Squat Knee Rest Low Pulley Station Lat Bar VKR* Arm *V ertical Knee Raise Weight Pin Adjustment Handle Butterfly Ar.
5 ASSEMBL Y Make sure that you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and masking tape.
1. Locate and open the parts bags labeled “FRAME ASSEMBL Y 1” and “FRAME ASSEMBL Y 2.” Press a 2” Square Inner Cap (105) into the open end of the Long Base (120). Insert eight 5/16” x 2 1/2” Carriage Bolts (1 10) up through the Long Base (120) and the Short Base (2) as shown.
4. Press a 1 1/2” Square Inner Cap (67) into the Butterfly Frame Stop (126). Attach the Butterfly Frame Stop (126) to the Butterfly Upright (3) with two 5/16” x 3 3/4” Bolts (92), two 5/16” W ashers (90), and two 5/16” Nylon Locknuts (86).
8 7. Press a 2” x 3” Inner Cap (58) into the top of the Squat Upright (4). Slide the Squat Upright ont o the two indicated 5/16” x 2 1/2” Car ria ge B olts (1 10) in the Long Base (120). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt.
9 9. Slide the Squat Slider (38) down onto the Squat Upright (4). 10. Insert the ends of two Weight Guides (42) into the indicated bracket on the Long Base (120). Slide two Weight Bumpers (49) onto the W eight Guides. Next, slide ten Weights (44) onto the W eight Guides.
10 14. Press a 2” x 2 1/2” Inner Cap (125) into the Butterfly Frame (47). Attach the tethers on the two “L”-pins (60) to the Butterfly Frame with a #8 x 3/4” Screw (98). Lubricate a 3/8” x 3” Bolt (107) with grease. Attach the Butterfly Frame (47) to the Butterfly T op Frame (7) with the Bolt and a 3/8” Nylon Locknut (87).
19. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.” Locate the VKR High Cable (74), which is 82 1/4” long and has an eyelet on one end and a thread- ed bolt on the other end.
12 20. Remove the preattached 3 1/2” Pulleys (78 [only one is shown]) from the Offset Double “U”- bracket (61). Wrap the V KR High Cable (74) under a 3 1/2” Pulley (78). Attach the Pulley to the Offset Double “U”-bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87).
13 24. Route the Lat Cable (88) over a 3 1/2” Pulley (78). Slide a plastic Long Cable T rap (102) onto a 3/8” x 1 3/4” Bolt (93). Attach the Pulley to the indicated bracket on the T op Frame (6) with the Bolt and a 3/8” Nylon Locknut (1 13). Make sure that the Long Cable T rap is turned to hold the Cable in the groove of the Pulley .
14 28. Wrap the Butterfly Cable (69) over a “V”-pulley (55). Attach the Pulley and a Long Cable T rap (102) to the indicated bracket on the Butterfly Upright (3) with a 3/8” x 2 1/2” Bolt (18) and a 3/8” Nylon Locknut (87). Make sure that the Long Cable T rap is turned to hold the Cable in the groove of the Pulley .
15 33 34 35 32. Locate the Leg Lever Cable (75), whi ch is 98 1 /2” long and has an eyelet on one end and a thread- ed pin on the other end. Route the eyelet end of the Cable through the Seat Upright (9) and attach it to the tab on the Leg Lever (10) with a 5/16” x 1” Shoulder Bolt (103) and a 5/16” Nylon Locknut (86).
16 36. Remove the preattached 3 1/2” Pulley (not shown) from the “U”-bracket (64). Attach the end of the Leg Lever Cable (75) to the “U”-bracket (64) with a 1/4” W asher (97) and a 1/4” Nylon Locknut (34). Note: Do not completely tighten the Nylon Locknut; it should be thread- ed only two turns onto the end of the Cable.
17 40. Wrap the VKR Low Cable (72) under a 3 1/2” Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 41. Route the VKR Low Cable (72) under the indicated stack of Weights (44).
18 44. Wrap the VKR Low Cable (72) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable T rap (68) between the lower set of holes in the “U”-bracket (64) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure that the Cable T rap is turned to hold the Cable in the groove of the Pulley .
19 48. Wrap the Squat Cable (73) under a 3 1/2” Pulley (78). Attach the Pulley and a Cable T rap to the sec- ond set of holes from the top in the indicated brack- et on the Long Base (120) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87).
20 52. Press two 3/4” x 1 1/2” Inner Caps (1 16) and a 1 1/4” Square Inner Cap (1 17) into the Seat Bracket (1 1). Attach the Seat (16) to the Seat Bracket (1 1) with two 1/4” x 3/4” Screws (1 14), a 1/4” x 1 1/2” Screw (99), and a 1/4” W asher (97).
21 56 57 58 11 4 11 4 12 17 56. Attach the Squat Arm (32) to the Squat Bracket (37) with two 3/8” x 2 1/2” Carriage Bolts (106), two 3/8” W ashers (91), and two 3/8” Nylon Locknuts (87).
22 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for various exercises.
23 ADJUSTING THE SQUA T ARM, SEA T , OR BUTTERFL Y BACKREST T o adjust the height of the Squat Arm (32), first turn the Adjustment Handle (65) on the Squat Bracket (37) counterclockwise several turns to loosen it. Next, pull the Handle and slide the Squat Bracket up or down to the desired position.
24 WEIGHT RESIST ANCE CHART The chart below shows the approximate weight resistance at each weight station. “T op” refers to the 10-pound top weight. The other numbers refer to the 10-pound weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
25 TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi- ately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent.
26 CABLE DIAGRAMS The cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia- grams on this page and the following page show the proper routing of the cables. The numbers in the diagrams show the routes of the cables.
27 Leg Lever Cable (75) VKR Low Cable (72) 1 1 3 2 4 5 6 7 9 2 3 4 8.
Cable Clip (83) 3 1/2" Pulley (78) (Not shown to scale) "V" Pulley (55) (Not shown to scale) 4 1/2" Pulley (1 19) (Not shown to scale) 3/8" x 3 3/4" Bolt (122) 3/8" .
3/8" x 2" Bolt (100) 3/8" x 1 3/4" Bolt (93) #10 x 1" Screw (14) 3/8" x 2 1/2" Bolt (18) 5/16" x 2 3/4" Bolt (85) 3/8" x 2 3/4" Bolt (101) 3/8&qu.
1 1/4" Square Inner Cap (1 17) 1" Round Inner Cap (29) 1 1/2" x 2” Inner Cap (21 2" Square Inner Cap (105) 1 1/2" Square Inner Cap (67) 2" x 3” Inner Cap (58) 3/4” .
P ART LIST—Model No. WESY38322 R1 102B Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 2 1/2” W asher 2 1 Short Base 3 1 Butterfly Upright 4 .
4 6 5 7 3 2 8 9 10 1 1 12 13 15 16 17 109 109 19 19 20 20 21 21 20 20 20 22 21 23 24 25 26 27 27 28 29 29 28 36 36 36 36 30 31 32 33 33 1 1 1 1 1 1 1 1 1 1 1 1 35 37 38 39 39 40 40 40 42 42 43 43 46 4.
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
An important point after buying a device Weider WESY38322 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Weider WESY38322 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Weider WESY38322 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Weider WESY38322 you will learn all the available features of the product, as well as information on its operation. The information that you get Weider WESY38322 will certainly help you make a decision on the purchase.
If you already are a holder of Weider WESY38322, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Weider WESY38322.
However, one of the most important roles played by the user manual is to help in solving problems with Weider WESY38322. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Weider WESY38322 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
