Instruction/ maintenance manual of the product DS-350 Wayne-Dalton
Go to page of 12
IMPORT A NT NOT ICE! ! Read the enclos ed instructions ca refully before attempting to install this door. Pay close attention to all w arnings a nd important safety notices.
2 CAUTION CAUTION WARNING IMPORTANT! HINT: NOTE: IMPORTA NT SA FETY NOTICES Read the enclos ed instructions ca refully before attempting installation. If there are any questions about any of the procedures, do not perform the w ork. Ins tead, have a qualified door agency do the installation or repairs.
3 INTRODUCTION This manual's main function is to assis t the installer in correctly mounting doors with due regard for safety , operation, and sound construction pra ctices.
4 STEP 1 UNPACKING DOORS Doors shipped by common ca rrier arrive at the job site packed in cardboard. Before removing the door from the packag ing, inspect the door and packa ging for visible signs of damage . If damage is noted, file a freight claim with the freight c ompany immediately .
5 STEP 3 INS TALLING MOUNTING ANG LES AND GUIDES Obtain the appropriate Bolt Line (BL) measurement from the chart below. Use Openin g Width l isted on packi ng slip. Any variation between the a ctual opening w idth and the width listed on the packing slip is to be ignore d.
6 Trim the top of eac h wear strip at a 45° angle as shown and clip onto the appropriate leg of each guide. Be sure that trimmed edges of the wear strips end just below the flare of the guides. Install the bottom bar stops wit h the same 5/ 16-18 x 5/8” truss head bolts and flange nuts used to assemble the guides (no washer).
7 side and position the door as close as possible to the door hea der. Be sur e that the door is able to r evolve without scraping aga inst door header or guides.
8 STEP 8 INSTALL SLIDE B OLT LOCKS I nstall slide bolt locks, if provided, as shown. I nstall the lift ha ndle to bottom bar angle at this time. STEP 9 L UBRICATE AND ADJUST THE GUIDES L ubricate the insides of the guides and wearstrips with weather resistant lubrica tin g spr ay .
9 Place a large pi pe wrench in position on the door axle as s hown and slightly loosen bot h ax le saddle castings. Pul l down on the wrench for m ore spring tension and let up on the wrench f or less spring tension. A s saddle cas tings are loosened, hold w re nch securel y .
10 REDUCED DRIVE CHAIN HOIST INSTALLATION INST RUCTIONS (if applicable) STEP 12 ALIGN THE SPROCKETS Feed the hand chain through the pocket wheel assembly (installed in step #4), around the cast iron hand c hain wheel, and conne ct the two end links.
11 Item Description Item Description 1 Top Sheets - Give Length 18 1/4-20 x 1” Slotted Screw, Washer & Ny lon Nut 2 Intermediate Sheets - Give L ength 19 Mounti ng Angle, Give Mounti ng Condit i.
12 Roll-Up Sheet Door LIMITED WARRANTY Wayne-Dalton Corp P.O. B ox 67- Mt. Ho pe, Ohio 4 4660 The Manu facturer warrants the ROLL-UP SHEET DOOR and hardware fittings for a perio d of ONE YEAR from the time o f delivery against any defects in workman ship or material.
An important point after buying a device Wayne-Dalton DS-350 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wayne-Dalton DS-350 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wayne-Dalton DS-350 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wayne-Dalton DS-350 you will learn all the available features of the product, as well as information on its operation. The information that you get Wayne-Dalton DS-350 will certainly help you make a decision on the purchase.
If you already are a holder of Wayne-Dalton DS-350, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wayne-Dalton DS-350.
However, one of the most important roles played by the user manual is to help in solving problems with Wayne-Dalton DS-350. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wayne-Dalton DS-350 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
