Instruction/ maintenance manual of the product 9600 Thermoguard Wayne-Dalton
Go to page of 8
P ART NO . 248438 TOP BRACKET FLAGANGLE HORIZONT AL TRACK VERTICAL TRACK CENTER HINGE #3 END HINGE BOTTOM BRACKET REAR SUPPORT ASSEMBL Y (NOT SUPPLIED) HORIZONT AL ANGLE ROLLER TL-2 JAMB BRACKET #2 EN.
IMPORT ANT SAFETY NOTICES Read these instructions carefully before attempting installation. If in question about any of the proce- dures, do not perform the work. Instead, have a qualified door agency do the installation or repairs. 1. W ear protective gloves during installation to avoid possible cuts from sharp metal edges.
IMPORT ANT! DOOR OPENING PREP ARA TION IS CRITICAL FOR PROPER DOOR INST ALLA TION. CHECK THE OPENING TOP , AND SIDES TO ENSURE IT IS LEVEL AND SQUARE. CORRECT IF NECESSARY BEFORE INST ALLING NEW DOOR. IMPORT ANT! IF INST ALLING A REPLACEMENT DOOR, CHECK THE OPENING SIZE AND NEW DOOR SIZE, MAKING SURE THEY MA TCH BEFORE REMOVING EXISTING DOOR.
FLA GANGLE (2) 5/16 x 1-5/8 LAG SCREW TOP SECTION NOTE: CABLE SHOULD BE BETWEEN TRACK AND DOOR AND BEHIND ROLLERS 10 8 TOP BRACKET (4) 1/4-20 x 5/8 SELF T APPING SCREWS 1 ST SET OF HOLES ON 9.
T H G I E H R O O D1 - L T2 - L T3 - L T " 0 ' 6 K C A R T " 4 6 ) m m 6 2 6 1 ( M O T T O BM O T T O BA / N " 5 ' 6 K C A R T " 9 6 ) m m 3 5 7 1 ( E L D D I MM O T T O .
Locate the center of the door and mark a vertical pencil line on the spring pad. Then measure the distance from the center of the mounting hole in the end bearing bracket to the top of the door . Using that same distance, mark a horizon- tal line on the spring pad, measuring up from the top of the door .
Permanently attach the vinyl weather stripping to both door jambs and the header . Now , lift the door and check it s balance. Unwind spring(s) if door lifts by itself or if it is hard to pull down. W ind spring(s) if door is difficult to lift or too easy to pull down.
SCREW EYE A T 48 TO 50 (1220 to 1270 mm) FROM FL OOR PULL ROPE TIE PULL ROPE TO BOTTOM BRACKET 19 T wist the No. 6 screw eye into the wood jamb approximately 48 to 50 (1220 to 1270 mm) from the floor . T ie the pull rope to the screw eye and to the bottom bracket as shown.
An important point after buying a device Wayne-Dalton 9600 Thermoguard (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wayne-Dalton 9600 Thermoguard yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wayne-Dalton 9600 Thermoguard - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wayne-Dalton 9600 Thermoguard you will learn all the available features of the product, as well as information on its operation. The information that you get Wayne-Dalton 9600 Thermoguard will certainly help you make a decision on the purchase.
If you already are a holder of Wayne-Dalton 9600 Thermoguard, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wayne-Dalton 9600 Thermoguard.
However, one of the most important roles played by the user manual is to help in solving problems with Wayne-Dalton 9600 Thermoguard. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wayne-Dalton 9600 Thermoguard along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
