Instruction/ maintenance manual of the product 9100 Wayne-Dalton
Go to page of 9
www .wayne-dalton.com W indload P ost 9100/9600/9900 9100/9600/9900 9100/9600/9900 9100/9600/9900 9100/9600/9900 Installation Instructions © Copyright 2002 W ayne-Dalton Corp. New 1/6/2002 305214 See garage door owner’s manual for warranty information.
2 Packaged Part s NOTE: The quantities below represent a single post for a single car garage. Double car doors require (2) post s. The quantities for the parts below (with the exception of SLIDE LOCKS) are doubled for double car doors.
Required T ools 3 J-Strut Inst allation IMPOR T ANT! Refer to the option code drawing (supplied) for windload post location(s). Place the 12” J-struts onto the lower rib of each door panel and center over the required position per the option code drawing.
Bottom Bracket Inst allation Locate the bottom bracket assembly and align it to the bottom of the post. Secure the bottom bracket to the bottom of the windload post using (4) 1/4-20 x 1 1/16” self-drilling screws. (see Fig. 3 ) NOTE: The bottom of the windload post is flush while the top is offset.
T op Plate Extension Inst allation Locate the top plate extension and top strap bracket. Place the top strap bracket onto the top plate extension and adjust so that the holes in the top strap bracket align with the corresponding door model holes in the top plate extension.
6 Install slide lock on the second section of the door . Secure the lock to the section with (4) 1/4-20 x 1 1/16” self drilling screws. Square lock assembly with door section and hole in vertical track. The slide lock should be spaced approximately 1/8” from the section edge.
Measure the distance from the top of the windload post to the center of the bottom strap (see Fig. 14 ). Use that measurement for the displacement between the center of the extra header lock bracket and half-hinge tube. Position the half-hinge on the bottom mounting block and secure the half-hinge using (2) 5/16” x 1-5/8” lag screws.
Att aching the Inst allation Decals After the installation is complete, locate an easily visible location on the inside of the garage door and the post(s) and place the provided installation decals onto the door and post(s) for future reference. IMPOR T ANT! DECALS MUST BE A TT ACHED T O BOTH DOOR AND POST(S).
3 2 1 9 W indload Label Locations 1 Applied by Installer - One (1) Emergency High Wind Situations T ags (161384) per post -T ags are to be applied to post(s) when stored on wall for constant reminder to consumer . 2 3 Applied by Installer - One (1) Florida Windload Inst allation Label (305213) -Only on doors specified with one or more posts.
An important point after buying a device Wayne-Dalton 9100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wayne-Dalton 9100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wayne-Dalton 9100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wayne-Dalton 9100 you will learn all the available features of the product, as well as information on its operation. The information that you get Wayne-Dalton 9100 will certainly help you make a decision on the purchase.
If you already are a holder of Wayne-Dalton 9100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wayne-Dalton 9100.
However, one of the most important roles played by the user manual is to help in solving problems with Wayne-Dalton 9100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wayne-Dalton 9100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
