Instruction/ maintenance manual of the product 8000 Wayne-Dalton
Go to page of 8
Wayne-Dalton Corp . P .O. Box 67 Mt. Hope, OH 44660 www .wayne-dalton.com WINDLO AD POST W ayneMark™8000, 8100 INST ALLA TION INSTRUCTIONS © Copyright 2007 Wayne-Dalton Corp. Rev3 6/26/2007 307330 See garage door owner ’ s manual for warranty information.
2 HALF HINGE (2) # 130352 HEADER LOCK BRACKET (2) # 141092 TOP PLA TE EXTENSION (1) # 305205 TOP STRAP BRACKET (1) # 305206 WINDLOAD POST ASSEMBL Y # 305207 - (7’) # 305332 - (8’) STRAPS (8) # 307.
Required T ools 3 JR. “A” Frame Installation IMPOR T ANT! Refer to the windload specifi cation draw- ings (supplied) for windload post location(s). Place the “A” frame brackets below the center hinges of each intermediate section, fasten with (2) 1/4-20 x 1 1/16” self drilling screws (see Fig.
Bottom Bracket Installation Locate the bottom bracket assembly and align it to the bottom of the post. Secure the bottom bracket to the bottom of the windload post using (4) 1/4-20 x 1 1/16” self-drilling screws. (see Fig. 3 ) NOTE: The bottom of the windload post is fl ush while the top is offset .
T op Plate Extension Installation Locate the top plate extension and top strap bracket. Place the top strap bracket onto the top plate extension and adjust so that the holes in the top strap bracket align with the corresponding door model holes in the top plate extension.
6 Install side lock on the second section from the bottom of the door . Square side lock assembly with door sec- tion and hole in vertical track. The side lock should be spaced approximately 1/8” from the section edge. Secure the side lock to the section with (4) 1/4-20 x 1 1/16” self drilling screws.
Slide the windload post(s) into storage header bracket(s) and secure the bottom strap(s) to the half hinge(s) using the 3-1/2” carriage bolt and wing nut. Place all remaining wing nuts and carriage bolts into the remaining straps for storage. Insert plastic plug into hole in fl oor .
3 2 1 W indload Label Locations Attaching the Installation Decals After the installation is complete, locate in a obviously visible location on the inside of the garage door and the post(s) and place the provided installation labels and tag(s) onto the door and post(s) for future reference.
An important point after buying a device Wayne-Dalton 8000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wayne-Dalton 8000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wayne-Dalton 8000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wayne-Dalton 8000 you will learn all the available features of the product, as well as information on its operation. The information that you get Wayne-Dalton 8000 will certainly help you make a decision on the purchase.
If you already are a holder of Wayne-Dalton 8000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wayne-Dalton 8000.
However, one of the most important roles played by the user manual is to help in solving problems with Wayne-Dalton 8000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wayne-Dalton 8000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
