Instruction/ maintenance manual of the product 6600 Wayne-Dalton
Go to page of 22
IMPORT ANT NO TICES! The complete Installation Instructions and Owner’ s Manual are available at no charge from: Wayne-Dalton, a Division Of Overhead Door Corporation, P .
Important Safety Instructions DEFINITION OF KEY WORDS USED IN THIS MANUAL: W ARNING W ARNING INDICA TES A POTENTIALL Y HAZARDOUS SITUA TION WHICH; IF NOT AVOIDED , COULD RESUL T IN SEVERE OR FA T AL INJURY . CAUTION: PROPER TY DAMAGE OR INJURY CAN RESUL T FROM FAILURE TO FOLLOW INSTRUCTIONS.
Pull down rope (if included) Inside lift handles Cable drums RH/LH Torsion springs RH/LH Center bracket (as required) Center bracket bushing (as required) Lift handles Pull handles Stud plate (as requ.
NOTE: If nailing product at 40°F or below , pre-drilling is required. NOTE: Allow the weatherstrips to return to room temperature prior to nailing to jambs.
5 A. FLAG ANGLES (AS REQUIRED): A1. Quick Install (Q.I.) Flag Angles A2. Fully Adjustable (F .A.) Flag Angles B. JAMB BRACKETS (AS REQUIRED): B1. Quick Install (Q.I.) Jamb Brackets B2. Fully Adjustable (F .A.) Jamb Brackets C. TRACK ROLLERS: C1. Short Stem T rack Rollers C2.
INST ALLA TION Before installing your door , be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door . NOTE : Reference TDS 160 for general garage door terminology at www.
slot pattern in the 3rd hole set and (1) 1/4” - 20 x 9/16” track bolt and (1) 1/4” - 20 flange hex nut. Repeat for other side. F .A. jamb bracket 1/4”- 20 x 9/16” T rack bolt 1/4”- 20 Fla.
Strutting Schedule Door Height # Of Sections Solid Or Glazed Door Width 8’0” - 9’0” 10’0” 12’0” - 14’0” 15’0” - 18’0” 7’0” - 8’0” 4 Solid N/A 2” Strut, T op of top section 2” Struts, T op of T op, Lock and Bottom sections 2” Struts, T op of T op, Int.
Bottom section (2) 1/4” x 2-1/2” Carriage bolts Bottom rail Center rail Pull handle (2) 1/4”- 20 Flange hex nuts Backer plate Lift Handle(s) Tools Required: Power drill, 1/4” Drill bit, 7/16.
Vertical track assembly Jamb bracket Flag angle Flag angle lag screw locations 5/16” x 1-5/8” Lag screws Bottom section T rack rollers 12R F A 3/8” to 5/8” Spacing Bottom section Vertical trac.
5/16”-18 x 3/4” Carriage bolt (4) 1/4”-20 x 11/16” Self drilling screws T op fixture base T op fixture slide 5/16”-18 Hex nut End cap T op section Short stem track roller Top Section Tools Required: Hammer, Step ladder, Tape measure 15 Place the top section in the opening.
section. Align the bottom of the horizontal track with the top of the vertical track. Tighten the horizontal track to the Flag Angle / Angle Mount with (2) 1/4” - 20 x 9/16” track bolts and (2) 1/4” - 20 flange hex nuts.
T ypicall center bracket Vertical line Mounting surface Equal distance (top of door section to horizontal line) Horizontal line T ypicall center of end bearing bracket IF YOUR DOOR DID NO T COME WITH .
T orsion keyed shaft Center bearing Red cable drum (left hand side) Black cable drum (right hand side) Coupler halves Center coupler assembly (3) 3/8” - 16 x 1-3/4” Hex head screws and (3) 3/8” .
NOTE: If you have torsion keyed shaft(s), insert (1) key into the slot of both the cable drum and the slot in the torsion keyed shaft, as shown. Rotate the left hand drum and torsion shaft until counterbalance lift cable is taut.
7’3” 7-7/8 7’6” 8 7’9” 8-1/4 8’0” 8-3/4 Alternately inserting the winding rods into the holes of the spring winding cone, rotate the winding cone upward toward the ceiling, 1/4 turn at a time, until the required number of complete turns for your door height is achieved.
Vice clamp Horizontal tracks 2nd T rack roller Vice clamp 5/16”-18 x 1-1/4” Hex bolt must extend into the track to serve as a roller stop Perforated angle Sound framing members Horizontal track (3.
Door Arm Hookup Align hole in the door arm with holes in operator bracket tabs, as shown. Attach with 5/16” x 1-3/4” cotter pin and cotter ring, as shown.
Cleaning Y our Garage Door IMPORT ANT : DO NOT USE A PRESSURE WASHER ON YOUR GARAGE DOOR! While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time.
are properly protected against moisture or other contaminants. Wood doors, in a non-finished condition, must not be transported or stored where the wood surfaces can be exposed to moisture or other contaminants. Wood (Surface Preparation) All surfaces must be clean, free of dust and dirt and any other contamination.
Limited Lifetime warranty Model 6600 Wayne Dalton, a division of Overhead Door Corporation (“Seller”) warrants to the original purchaser of the Model 6600 (“Product”), subject to all of the te.
AFTER INST ALLA TION IS COMPLETE, F ASTEN THIS MANUAL NEAR GARAGE DOOR FOR EASY REFERENCE. PLEASE DO NO T RETURN THIS PRODUCT TO THE STORE Thank you for your pur chase. Please Do Not Return This Product T o The Store. Please call 1-866-569-3799 (Press Option 1) and follow the prompts to contact the appropriate customer ser vice agent.
An important point after buying a device Wayne-Dalton 6600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wayne-Dalton 6600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wayne-Dalton 6600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wayne-Dalton 6600 you will learn all the available features of the product, as well as information on its operation. The information that you get Wayne-Dalton 6600 will certainly help you make a decision on the purchase.
If you already are a holder of Wayne-Dalton 6600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wayne-Dalton 6600.
However, one of the most important roles played by the user manual is to help in solving problems with Wayne-Dalton 6600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wayne-Dalton 6600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
