Instruction/ maintenance manual of the product F5D8631-4 Belkin
Go to page of 102
User Manual F5D 8 631 - 4 N1 Wireless Modem Router.
T able of Contents 1. Introduction .................................................................. 1 Advantages of a Wireless Network ................................. 1 Placement of your N1 Wireless Modem Router ............... 3 2. Product Overview .
EN-2 Intr oduction EN-1 EN-2 EN-1 Thank you for purchasing the Belkin N1 Wireless Modem Router (the Modem Router). Following are two short sections—the first discusses the benefits of home networking, and the other outlines best practices that maximize your wireless home network range and performance.
EN-2 Intr oduction EN-2 2 1 3 4 5 6 7 8 9 1 0 section Revolutionary N1 Wireless Technology with MIMO (N1 MIMO) Your Belkin N1 Wireless Modem Router uses a new smart-antenna technology called Multiple Input Multiple Output (MIMO). N1 MIMO complies with the IEEE draft 802.
EN-4 EN-3 Intr oduction EN-4 EN-3 Intr oduction Placement of your N1 Wireless Modem Router Important Factors for Placement and Setup Your wireless connection will be stronger the closer your computer is to your Modem Router. Typical indoor operating range for wireless devices is between 100 and 200 feet.
EN-4 Intr oduction Intr oduction EN-4 Intr oduction 2 1 3 4 5 6 7 8 9 1 0 section 2. Avoid Obstacles and Interference Avoid placing your Modem Router near devices that may emit radio “noise,” such as microwave ovens.
EN-6 EN-5 Intr oduction EN-6 EN-5 Intr oduction • Experiment with more than one of the available channels, in order to find the clearest connection and avoid interference from neighboring cordless phones or other wireless devices.
EN-6 Intr oduction Intr oduction EN-6 Intr oduction 2 1 3 4 5 6 7 8 9 1 0 section F r ee T ech Support * You can find additional support information on our website www.belkin.com through the tech-support area. If you want to contact technical support by phone, please call the number you need from the list below*.
EN-8 EN-7 Pr oduct Overview EN-8 EN-7 Pr oduct Overview Product Features In minutes you will be able to share your Internet connection and network your computers. The following is a list of features that make your new Belkin N1 Wireless Modem Router an ideal solution for your home or small office network.
EN-8 Pr oduct Overview EN-8 2 1 3 4 5 6 7 8 9 1 0 section Integrated 10/100 4-Port Switch The Modem Router has a built-in, four-port network switch to allow your wired computers to share printers, data and MP3 files, digital photos, and much more. The switch features automatic detection so it will adjust to the speed of connected devices.
Pr oduct Overview Integr ated N1 Wireless Access Point N1 MIMO is an exciting new wireless technology based on the draft IEEE 802.11n specification. It employs MIMO (Multiple Input Multiple Output) smart-antenna technology that achieves data rates of up to 300Mbps.
Package Contents • Belkin N1 Wireless Modem Router • Quick Installation Guide • Belkin Setup Assistant Software CD • RJ11 Telephone Cord • RJ45 Ethernet Networking Cable • ADSL Microfilter* • Power Supply • User Manual in CD *ADSL microfilter varies by country.
EN-12 EN-11 Knowing your Modem Router EN-12 EN-11 Knowing your Modem Router The Modem Router has been designed to be placed on a desktop. All of the cables exit from the rear of the Modem Router for better organization and utility.
EN-12 Knowing your Modem Router EN-12 section 2 1 3 4 5 6 7 8 9 1 0 D. Modem Router/Power Status When you apply power to the Modem Router or restart it, a short period of time elapses while the Modem Router boots up. During this time, the “modem router” icon blinks.
EN-14 EN-13 Knowing your Modem Router EN-14 EN-13 H. Connec tio n to ADS L line - Gray This port is for connection to your ADSL line. Connect your ADSL line to this port. A RJ11 telephone cord is provided in the package. I. C onn ect io ns to Wir ed Com pu ter s - Yellow Connect your wired (non-wireless) computers to these ports.
EN-14 Connecting and Configuring your Modem Router EN-14 section 1 4 5 6 7 8 9 1 0 Ver ify the cont en ts of you r box. You sho uld have th e foll owi ng: • Belkin N1 Wireless Modem Router • RJ11 .
EN-16 EN-15 Connecting and Configuring your Modem Router EN-16 EN-15 Connecting and Configuring your Modem Router B. Retrieve the yellow RJ-45 cable that comes with your Modem Router. First connect it to any yellow port labeled “to Wired Computers” on the back of your Modem Router.
EN-16 Connecting and Configuring your Modem Router EN-16 section 2 1 3 4 5 6 7 8 9 1 0 Replacing an Existing Modem or Modem Router Follow these steps if you currently have a modem or a modem router that you will be replacing with your new Modem Router A.
EN-18 EN-17 Connecting and Configuring your Modem Router EN-18 EN-17 Connecting and Configuring your Modem Router A. Shut down any programs that are running on your computer at this time. Turn off any firewall or Internet-connection-sharing software on your computer.
EN-18 Connecting and Configuring your Modem Router EN-18 section 2 1 3 4 5 6 7 8 9 1 0 Select Country Select your country from the drop-down box. Click “Begin” to continue. Confirmation Screen Verify that you have completed all QIG steps by checking the box to the right of the arrow.
EN-20 EN-19 Connecting and Configuring your Modem Router EN-20 EN-19 Connecting and Configuring your Modem Router 1.2 Verifying Hardware Connections The Setup Assistant will now verify your hardware connection. 1.3 Naming your Wireless Network The Setup Assistant will display the default wireless network name or Service Set Identifier (SSID).
EN-20 Connecting and Configuring your Modem Router EN-20 section 2 1 3 4 5 6 7 8 9 1 0 1.5 Configuring the Modem Router The Setup Assistant will now configure your Modem Router by sending data to the Modem Router and restarting it. Wait for the on-screen instructions.
EN-22 EN-21 Connecting and Configuring your Modem Router EN-22 EN-21 Connecting and Configuring your Modem Router You can use the Setup Assistant to set up your other wired and wireless computers to connect to the Internet by clicking “Next”.
EN-22 Connecting and Configuring your Modem Router EN-22 section 2 1 3 4 5 6 7 8 9 1 0 1.7 Optional: Assistance Connecting Other Computers This optional step will help you to connect additional wired and wireless computers to your network. Follow the on-screen instructions.
EN-24 EN-23 Alter nate Setup Method EN-24 EN-23 Alter nate Setup Method See the QIG or Step 1: Hardware Connections from the previous section. See the section in this User Manual called “Manually Configuring Network Settings” for directions. Using your Internet browser, you can access the Modem Router’s Web-Based Advanced User Interface.
EN-24 Alter nate Setup Method EN-24 section 2 1 3 4 5 6 7 8 9 1 0 Logging into the Modem Router You will see the Modem Router’s home page in your browser window. The home page is visible to any user who wants to see it. To make any changes to the Modem Router’s settings, you have to log in.
EN-26 EN-25 Alter nate Setup Method EN-26 EN-25 Alter nate Setup Method 1. Qui ck -Na vig ati on Lin ks You can go directly to any of the Modem Router’s advanced UI pages by clicking directly on these links. The links are divided into logical categories and grouped by tabs to make finding a particular setting easier to find.
EN-26 Alter nate Setup Method EN-26 section 2 1 3 4 5 6 7 8 9 1 0 5. Int er net -St atu s Indi cat or This indicator is visible in all pages of the Modem Router, indicating the connection status of the Modem Router. When the indicator says “Connected” in blue, the Modem Router is connected to the Internet.
EN-28 EN-27 Alter nate Setup Method EN-28 EN-27 Alter nate Setup Method The “Internet/WAN” tab is where you will set up your Modem Router to connect to your Internet Service Provider (ISP).
EN-28 Alter nate Setup Method EN-28 section 2 1 3 4 5 6 7 8 9 1 0 Connection Type From the “Connection Type” page, you can select one of these five connection types based on the instruction provid.
EN-30 EN-29 Alter nate Setup Method EN-30 EN-29 Alter nate Setup Method Setting your ISP Connection Type to PPPoE or PPPoA PPPoE (Point-to-Point Protocol over Ethernet) is the standard method of connecting networked devices. It requires a user name and password to access the network of your ISP for connecting to the Internet.
EN-30 Alter nate Setup Method EN-30 section 2 1 3 4 5 6 7 8 9 1 0 7. Dis con nec t afte r of x minu tes of no acti vit y - Checking the box and enter the number of minute that you want the modem router to auto disconnect after no activity. After this time has been exceeded, the connection will be terminated.
EN-32 EN-31 Alter nate Setup Method EN-32 EN-31 Alter nate Setup Method Setting your Connection Type to Dynamic IP (1483 Bridged) This connection method bridges your network and ISP’s network together. The Modem Router will obtain IP address automatically from your ISP’s DHCP server.
EN-32 Alter nate Setup Method EN-32 section 2 1 3 4 5 6 7 8 9 1 0 Setting your ISP Connection Type to Static IP (IPoA) This connection type is also called “Classical IP over ATM” or “CLIP”, which your ISP provides a fixed IP for your Modem Router to connect to the Internet.
EN-34 EN-33 Alter nate Setup Method EN-34 EN-33 Alter nate Setup Method Setting your Connection Type to Modem Only (Disable Internet Sharing) In this mode, the Modem Router simply acts as a bridge passing packets across the DSL port. It requires additional software to be installed on your computers in order to access the Internet.
EN-34 Alter nate Setup Method EN-34 section 2 1 3 4 5 6 7 8 9 1 0 Setting Custom Domain Name Server (DNS) Settings A “Domain Name Server” is a server located on the Internet that translates Universal Resource Locaters (URLs) like “www.belkin.com” to IP addresses.
EN-36 EN-35 Using the Web-Based Advanced User Interface EN-36 EN-35 Using your Internet browser, you can access the Modem Router’s Web-Based Advanced User Interface. In your browser, type “192.168.2.1” (do not type in anything else such as “http://” or “www”) then press the “Enter” key.
EN-36 Using the Web-Based Advanced User Interface EN-36 section 2 1 3 4 5 6 7 8 9 1 0 Changing LAN Settings All settings for the internal LAN setup of the Modem Router can be viewed and changed here. 1. IP Ad dre ss The “IP address” is the internal IP address of the Modem Router.
EN-38 EN-37 Using the Web-Based Advanced User Interface EN-38 EN-37 Using the Web-Based Advanced User Interface 4. IP Pool The range of IP addresses set aside for dynamic assignment to the computers on your network. The default is 2–100 (99 computers).
EN-38 Using the Web-Based Advanced User Interface EN-38 section 2 1 3 4 5 6 7 8 9 1 0 Viewing the DHCP Client List Page You can view a list of the computers (known as clients), which are connected to your network.
EN-40 EN-39 Using the Web-Based Advanced User Interface EN-40 EN-39 Using the Web-Based Advanced User Interface Changing the Wireless Network Name (SSID) To identify your wireless network, a name called the SSID is used. The SSID is your network name.
EN-40 Using the Web-Based Advanced User Interface EN-40 section 2 1 3 4 5 6 7 8 9 1 0 Changing the Wireless Channel There are a number of operating channels from which you can choose—in the United Kingdom (and most of Europe) and Australia, there are 13.
EN-42 EN-41 Using the Web-Based Advanced User Interface EN-42 EN-41 Using the Web-Based Advanced User Interface Using the Broadcast SSID Feature No te : Th is ad va n ce d fe at ur e sh ou l d b e e mp lo y ed by ad va n ce d us er s o nl y . F or se cu r it y, yo u ca n c ho o se no t t o b ro a dc a st yo ur ne t wo rk ’ s S SI D .
EN-42 Using the Web-Based Advanced User Interface EN-42 section 2 1 3 4 5 6 7 8 9 1 0 Yo u m ay us e ei th er th e Pu sh Bu t to n C on f ig u ra ti o n ( PB C) me t ho d or PI N me th o d t o a ll ow a d ev i ce ac c es s t o y ou r wi re le s s n et w or k.
EN-44 EN-43 Using the Web-Based Advanced User Interface EN-44 EN-43 Using the Web-Based Advanced User Interface WPA2 Requirements IMPORTANT: In order to use WPA2 security, all your computers and wireless client adapters must be upgraded with patches, driver, and client utility software that supported WPA2.
EN-44 Using the Web-Based Advanced User Interface EN-44 section 2 1 3 4 5 6 7 8 9 1 0 3. For “Encryption Technique”, select “TKIP”, “AES”, or “TKIP+AES”. This setting will have to be identical on the wireless clients that you set up. 4.
EN-46 EN-45 Using the Web-Based Advanced User Interface EN-46 EN-45 Using the Web-Based Advanced User Interface Setting WPA-PSK 1) From the “Security Mode” drop-down menu, select “WPA-PSK (no server)”. 2) For “Encryption Technique”, select “TKIP” or “AES”.
EN-46 Using the Web-Based Advanced User Interface EN-46 section 2 1 3 4 5 6 7 8 9 1 0 Setting WEP Encryption Note to Mac users: The “Passphrase” option will not operate with Apple ® AirPort ® . To configure encryption for your Mac computer, set the encryption using the manual method described in the next section.
EN-48 EN-47 Using the Web-Based Advanced User Interface EN-48 EN-47 Using the Web-Based Advanced User Interface Using a Hexadecimal Key A hexadecimal key is a mixture of numbers and letters from A–F and 0–9. 64-bit keys are 10 digits long and can be divided into five two-digit numbers.
EN-48 Using the Web-Based Advanced User Interface EN-48 section 2 1 3 4 5 6 7 8 9 1 0 Using the Access Point Mode Note: This advanced feature should be employed by advanced users only. The Modem Router can be configured to work as a wireless network access point.
EN-50 EN-49 Using the Web-Based Advanced User Interface EN-50 EN-49 Using the Web-Based Advanced User Interface Setting MAC Address Control The MAC address filter is a powerful security feature that allows you to specify which computers are allowed on the wireless network.
EN-50 Using the Web-Based Advanced User Interface EN-50 section 2 1 3 4 5 6 7 8 9 1 0 Setting up a Deny Access List The “Deny Access” list lets you specify computers that you DO NOT want to access the network. Any computer in the list will not be allowed access to the wireless network.
EN-52 EN-51 Using the Web-Based Advanced User Interface EN-52 EN-51 Using the Web-Based Advanced User Interface Configuring the Firewall Your Modem Router is equipped with a firewall that will protect.
EN-52 Using the Web-Based Advanced User Interface EN-52 section 2 1 3 4 5 6 7 8 9 1 0 Configuring Internal Forwarding Settings The Virtual Servers function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Modem Router to your internal network.
EN-54 EN-53 Using the Web-Based Advanced User Interface EN-54 EN-53 Using the Web-Based Advanced User Interface Setting Client IP Filters The Modem Router can be configured to restrict access to the Internet, e-mail, or other network services at specific days and times.
EN-54 Using the Web-Based Advanced User Interface EN-54 section 2 1 3 4 5 6 7 8 9 1 0 Enabling the Demilitarized Zone (DMZ) The DMZ feature allows you to specify one computer on your network to be placed outside of the firewall.
EN-56 EN-55 Using the Web-Based Advanced User Interface EN-56 EN-55 Using the Web-Based Advanced User Interface Setting up the Modem Router’s Dynamic DNS Update Client You must register with DynDNS.org’s free update service before using this feature.
EN-56 Using the Web-Based Advanced User Interface EN-56 section 2 1 3 4 5 6 7 8 9 1 0 Blocking an ICMP Ping Computer hackers use what is known as “pinging” to find potential victims on the Internet. By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there.
EN-58 EN-57 Using the Web-Based Advanced User Interface EN-58 EN-57 Using the Web-Based Advanced User Interface Restarting the Modem Modem Router Sometimes it may be necessary to restart or reboot the Modem Router if it begins working improperly. Restarting or rebooting the Modem Router will NOT delete any of your configuration settings.
EN-58 Using the Web-Based Advanced User Interface EN-58 section 2 1 3 4 5 6 7 8 9 1 0 Restoring Factory Default Settings Using this option will restore all of the settings in the Modem Router to the factory (default) settings. It is recommended that you back up your settings before you restore all of the defaults.
EN-60 EN-59 Using the Web-Based Advanced User Interface EN-60 EN-59 Using the Web-Based Advanced User Interface Saving a Current Configuration You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed.
EN-60 Using the Web-Based Advanced User Interface EN-60 section 2 1 3 4 5 6 7 8 9 1 0 2. A window will open that allows you to select the location where you want to save the configuration file. Select a location. You can name the file anything you want, or use the default name “Config”.
EN-62 EN-61 Using the Web-Based Advanced User Interface EN-62 EN-61 Using the Web-Based Advanced User Interface Restoring a Previous Configuration This option will allow you to restore a previously saved configuration. 1. Click “Browse”. A window will open that allows you to select the location of the configuration file.
EN-62 Using the Web-Based Advanced User Interface EN-62 section 2 1 3 4 5 6 7 8 9 1 0 2. You will be asked if you want to continue. Click “OK”. 3. A reminder window will appear. It will take up to 60 seconds for the configuration restoration to complete.
EN-64 EN-63 Using the Web-Based Advanced User Interface EN-64 EN-63 Using the Web-Based Advanced User Interface Updating the Firmware From time to time, Belkin may release new versions of the Modem Router’s firmware. Firmware updates contain feature improvements and fixes to problems that may have existed.
EN-64 Using the Web-Based Advanced User Interface EN-64 section 2 1 3 4 5 6 7 8 9 1 0 Downloading a New Version of Firmware If you click the “Check Firmware” button and a new version of firmware is available, you will see a screen similar to the one below: 1.
EN-66 EN-65 Using the Web-Based Advanced User Interface EN-66 EN-65 Using the Web-Based Advanced User Interface 2. When the save is complete, you will see the following window. Click “Close”. 3. The download of the firmware is complete. To update the firmware, follow the next steps in “Updating the Modem Router’s Firmware”.
EN-66 Using the Web-Based Advanced User Interface EN-66 section 2 1 3 4 5 6 7 8 9 1 0 3. The “Update Firmware” box will now display the location and name of the firmware file you just selected. Click “Update”. 4. You will be asked if you are sure you want to continue.
EN-68 EN-67 Using the Web-Based Advanced User Interface EN-68 EN-67 Using the Web-Based Advanced User Interface Changing System Settings The “System Settings” page is where you can enter a new administrator password, set the time zone, enable remote management, and turn on and off the NAT function of the Modem Router.
EN-68 Using the Web-Based Advanced User Interface EN-68 section 2 1 3 4 5 6 7 8 9 1 0 Setting the Time and Time Zone The Modem Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server. This allows the Modem Router to synchronize the system clock to the global Internet.
EN-70 EN-69 Using the Web-Based Advanced User Interface EN-70 EN-69 Using the Web-Based Advanced User Interface The second method is to allow a specific IP address only to remotely manage the Modem Router.
EN-70 Using the Web-Based Advanced User Interface EN-70 section 2 1 3 4 5 6 7 8 9 1 0 Enabling/Disabling UPnP UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your Belkin Modem Router.
EN-72 EN-71 Manually Configuring Network Settings EN-72 EN-71 Set up the computer that is connected to the cable or DSL modem FIRST using these steps. You can also use these steps to add computers to your Modem Router after the Modem Router has been set up to connect to the Internet.
EN-72 Manually Configuring Network Settings EN-72 section 2 1 3 4 5 6 7 8 9 1 0 3. Next to “Configure” (2) , if “Manually” is selected, your Modem Router will need to be set up for a static IP connection type. Write the address information in the table below.
EN-74 EN-73 Manually Configuring Network Settings EN-74 EN-73 Manually Configuring Network Settings Manually Configuring Network Settings in Mac OS X 1. Click on the “System Preferences” icon. 2. Select “Network” (1) from the “System Preferences” menu.
EN-74 Manually Configuring Network Settings EN-74 Manually Configuring Network Settings section 2 1 3 4 5 6 7 8 9 1 0 Manually Configuring Network Settings 4. Select the “TCP/IP” tab (3) . Next to “Configure” (4) , you should see “Manually” or “Using DHCP”.
EN-76 EN-75 Manually Configuring Network Settings EN-76 EN-75 Manually Configuring Network Settings Manually Configuring Network Settings in Windows 2000, NT, or XP 1. Click “Start”, “Settings”, then “Control Panel”. 2. Double-click on the “Network and dial-up connections” icon (Windows 2000) or the “Network” icon (Windows XP).
EN-76 Manually Configuring Network Settings EN-76 Manually Configuring Network Settings section 2 1 3 4 5 6 7 8 9 1 0 Manually Configuring Network Settings Manually Configuring Network Settings in Windows 98 or Me 1. Right-click on “My Network Neighborhood” and select “Properties” from the drop-down menu.
EN-78 EN-77 Recommended Web Browser Settings EN-78 EN-77 Recommended Web Browser Settings In most cases, you will not need to make any changes to your web browser’s settings. If you are having trouble accessing the Internet or the advanced web-based user interface, then change your browser’s settings to the recommended settings in this section.
EN-78 Recommended Web Browser Settings EN-78 section 2 1 3 4 5 6 7 8 9 1 0 4. Make sure there are no check marks next to any of the displayed options: “Automatically detect settings”, “Use automatic configuration script”, and “Use a proxy server”.
EN-80 EN-79 T roubleshooting EN-80 EN-79 T roubleshooting Setup Assistant CD does not automatically start. If the CD-ROM does not start the Setup Assistant automatically, it could be that the computer is running other applications that are interfering with the CD drive.
EN-80 T roubleshooting EN-80 section 2 1 3 4 5 6 7 8 9 1 0 2. Unplug power to the Modem Router for 10 seconds, and then plug the power back into the Modem Router.
EN-82 EN-81 T roubleshooting EN-82 EN-81 T roubleshooting • The Setup Assistant completed installation, but my web browser doesn’t work. • I am unable to connect to the Internet. The “modem” LED on my Modem Router is off, and the “internet” LED is blinking.
EN-82 T roubleshooting EN-82 section 2 1 3 4 5 6 7 8 9 1 0 • The Setup Assistant completed installation, but my web browser doesn’t work. • I am unable to connect to the Internet. The “modem” LED on my Modem Router is on, and the “internet” LED is blinking.
EN-84 EN-83 T roubleshooting EN-84 EN-83 T roubleshooting • The Setup Assistant completed, but my web browser doesn’t work. • I am unable to connect to the Internet. The “modem” LED on my Modem Router is blinking, and the “internet” LED is solid.
EN-84 T roubleshooting EN-84 section 2 1 3 4 5 6 7 8 9 1 0 I can’t connect to the Internet wirelessly. If you are unable to connect to the Internet from a wireless computer, please check the following items: 1. Look at the lights on your Modem Router.
EN-86 EN-85 T roubleshooting EN-86 EN-85 T roubleshooting I can’t connect to the Internet wirelessly, but my network name is listed. If the name of your network is listed in the “Available Networks” list, please follow the steps below to connect wirelessly: 1.
EN-86 T roubleshooting EN-86 section 2 1 3 4 5 6 7 8 9 1 0 • My wireless network performance is inconsistent. • Data transfer is sometimes slow. • Signal strength is poor. • Difficulty establishing and/or maintaining a Virtual Private Network (VPN) connection.
EN-88 EN-87 T roubleshooting EN-88 EN-87 T roubleshooting I am having difficulty setting up Wired Equivalent Privacy (WEP) security on my Belkin Modem Router. 1. Log into your Modem Router. Open your web browser and type in the IP address of the Modem Router.
EN-88 T roubleshooting EN-88 section 2 1 3 4 5 6 7 8 9 1 0 I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin client card. The client card must use the same key as the Modem Router. For instance, if your Modem Router uses the key 00112233445566778899 AABBCC, then the client card must be set to the exact same key.
EN-90 EN-89 T roubleshooting EN-90 EN-89 T roubleshooting Do Belkin products support WPA? Not e: To use WPA security, all your clients must be upgraded to drivers and software that support it. At the time of this FAQ publication, a security patch download is available, for free, from Microsoft.
EN-90 T roubleshooting EN-90 section 2 1 3 4 5 6 7 8 9 1 0 I am having difficulty setting up Wireless Protected Access (WPA) security on a Belkin wireless client card for a home network.
EN-92 EN-91 T roubleshooting EN-92 EN-91 T roubleshooting I am NOT using a Belkin client card for a home network andI am having difficulty setting up Wireless Protected Access (WPA) security.
EN-92 T roubleshooting EN-92 section 2 1 3 4 5 6 7 8 9 1 0 3. Under the “Wireless Networks” tab, click the “Configure” button and you will see the following screen. 4. For a home or small business user, select “WPA-PSK” under “Network Administration”.
EN-94 EN-93 T roubleshooting EN-94 EN-93 T roubleshooting Belkin Wirel ess Comparison Chart Wireless Technology G (802.11g) G Plus MIMO (802.11g with MIMO MRC) N MIMO (draft 802.
EN-94 T roubleshooting EN-94 section 2 1 3 4 5 6 7 8 9 1 0 Fre e T ec h S up p o r t * * Na ti on a l ca ll r at es m ay a pp l y w w w. b el k in .c o m You can find additional support information on our website www.belkin. com through the tech-support area.
EN-96 EN-95 Information EN-96 EN-95 Information Caution: Exposure to Radio Frequency Radiation. The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized.
EN-96 Information EN-96 section 2 1 3 4 5 6 7 8 9 1 0 Canada-Industry Canada (IC) The wireless radio of this device complies with RSS 139 & RSS 210 Industry Canada. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B conforme á la norme NMB-003 du Canada.
EN-98 EN-97 Information EN-98 EN-97 Information Belkin Corporation Limited Lifetime Product Warranty What this warranty covers. Belkin Corporation warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship.
EN-98 Information EN-98 section 2 1 3 4 5 6 7 8 9 1 0 Belk in Cor por ati on res erv es the right to revie w the dam age d Belk in pro duct . All cost s of shi ppin g the Be lkin produ ct to Bel kin Corpo rat ion for insp ect ion sh all be bor ne sol ely by the purc hase r.
Information EN-99 section 2 1 3 4 5 6 7 8 9 1 0 dofc f5d8631.do c EC Declaration of Conformity to R&TTE Directive 1999/5/EC CE! Manufacturer : BELKIN LTD, EXPRESS BUSINESS PARK, SHIP TON WAY ,RUSH.
P75256ea-A N1 Wireless Modem Router © 2007 Belkin International, Inc. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. Mac, Mac OS, Apple, and AirPort are trademarks of Apple Computer, Inc., registered in the U.
An important point after buying a device Belkin F5D8631-4 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Belkin F5D8631-4 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Belkin F5D8631-4 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Belkin F5D8631-4 you will learn all the available features of the product, as well as information on its operation. The information that you get Belkin F5D8631-4 will certainly help you make a decision on the purchase.
If you already are a holder of Belkin F5D8631-4, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Belkin F5D8631-4.
However, one of the most important roles played by the user manual is to help in solving problems with Belkin F5D8631-4. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Belkin F5D8631-4 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
