Instruction/ maintenance manual of the product Power Painter Wagner SprayTech
Go to page of 19
English Owner’s Manual Read this manual for complete instructions Table of Contents Safety Information ................................................... 2 What’s in the Box .................................................... 3 Before you Begin .
This symbol indicates a hazardous situation, which, if not not avoided could result in death or serious injury. HAZARD: INJECTION INJURY A high pressure stream of paint produced by this equipment can pierce the skin and underlying tissues, leading to serious injury and possible amputation.
3 English Important Safety Information · Read all safety information before operating the equipment. SAVE THESE INSTRUCTIONS. Grounding Instructions This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.
English 4 Before You Begin Important Preparation Tips: Selecting the Proper Spray Tip: • It is important to mix the material thoroughly before you begin. Do not shake the material to mix it. Always stir the material gently but thoroughly before use.
5 English Material Container Setup 1. Remove the material container from the pump housing by turning the pump housing ring counterclockwise. 7. Twist the pump housing ring to thread the container onto the pump housing. Plug in the unit. 3. Fill the container with the material to be used.
English 6 Remote Suction Set Setup (optional) 1. Remove the material container from the pump housing by turning the pump housing ring counterclockwise. 7. Submerge the suction tube assembly into the material container and attach the container clip (l) to the side to hold it securely.
7 English Flow Control Knob / Practice Spraying 1. Turn the ow knob fully counterclockwise to maximum. 3. Turn the ow knob clockwise until you have a good spray pattern. 2. Point the sprayer at a scrap piece of wood or cardboard, and pull the trigger to prime the sprayer.
English 8 Title Usage Overspray: Priming with the Remote Suction Set: 1. If you are using the remote suction set, you will need to prime the sprayer by removing air from the system. To prime: Make sure the sprayer is plugged in, and turn the ow control knob counterclockwise to maximum.
9 English Title Spraying Technique 1. Keep your arm moving at constant speed and keep the sprayer at a constant distance from the surface. The sprayer should be triggered at the beginning of the stroke and released at the end of the stroke. 2. Keep the sprayer at right angles to the surface.
English 10 Title Using the Quick Flush Lid (latex materials only) Cleaning the material container: 1. Unplug the sprayer. Pour the remaining material back into the original container. Remove the suction tube. 4. Slide the pump housing assembly off the sprayer.
11 English Title Using the Quick Flush Lid (latex materials only) Cleaning the Remote Suction Set: You will need a garden hose to complete the steps below. If you do not have a garden hose available, or if you used oil- based materials, follow the Cleanup for Oil-Based Materials instructions on page 12-13 .
English 12 Title Cleanup - Oil-based Materials Cleaning the Material container: 1. Unplug the sprayer. Pour the remaining material back into the original container.
13 English Cleanup - Oil-based Materials Cleaning the Remote Suction Set: 1. Make sure the sprayer is unplugged. 2. Remove the suction tube from the material container and submerge into a container of the solvent appropriate to the type of material you sprayed (warm, soapy water for latex-based materials; mineral spirits for oil-based materials.
English 14 Title Cleaning the Components - Oil-based materials Reassembly - all materials 1. Turn the spray tip counterclockwise until it is removed. Pull out the atomizer valve, being careful not to lose it. 1. Slide the spring onto the front end of the piston.
15 English Maintenance Replacement Parts 1. Turn the sprayer upside-down while the material container is removed. Squeeze a small amount of standard household oil into both the intake (a) and return (b) openings on the pump housing. Atomizer valve: The atomizer valve is shaped to cause the material to spin as it comes out of the sprayer.
English 16 Troubleshooting Problem A. Motor will not run. B. Motor has a low hum and does not spray. C. Motor operates properly but does not spray. D. Material spitting or globbing. E. Excessive fogging. F. Runs and sags in paint. G. Material drips from spray tip guard.
50 Parts list • Liste de pièces • Lista de piezas (i) (a) (g) (h) (j) (p) (q) (r) (m) (b) (c) (d) (e) (f) (k) (l) (n) (o).
51 Parts list • Liste de pièces • Lista de piezas Item Article Articulo Part No. Nº de piéce Pieza No. English Description Français Description Español Descripción Quantity Quantite Cantidad.
52 Warranty • Garantie • Garantía Wagner Spray Tech Corporation 1770 Fernbrook Lane Plymouth, Minnesota 55447 Telephone 1-800-328-8251 Copyright © Wagner Spray Tech Corporation. All rights reserved, including right of reproduction in whole or in part, in any form.
An important point after buying a device Wagner SprayTech Power Painter (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Wagner SprayTech Power Painter yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Wagner SprayTech Power Painter - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Wagner SprayTech Power Painter you will learn all the available features of the product, as well as information on its operation. The information that you get Wagner SprayTech Power Painter will certainly help you make a decision on the purchase.
If you already are a holder of Wagner SprayTech Power Painter, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Wagner SprayTech Power Painter.
However, one of the most important roles played by the user manual is to help in solving problems with Wagner SprayTech Power Painter. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Wagner SprayTech Power Painter along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
