Instruction/ maintenance manual of the product GCO2C ML-114571 Vulcan-Hart
Go to page of 20
GCO2D & GCO2C GAS CONVECTION OVENS MODEL GCO2D M L-114569 GCO2C M L-114571 INST ALLA TION & OPERA TION MANU AL MODEL GCO2D VULCAN-HART DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC WWW.VULCANHART.COM P.O. BOX 696 LOUISVILLE, KY 40201-0696 FORM 30975 Rev.
– 2 – IMPORT ANT FOR Y OUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED.
– 3 – INST ALLA TION, OPERA TION AND CARE OF GCO2D & GCO2C GAS CONVECTION O VENS KEEP THIS MANUAL FOR FUTURE REFERENCE GENERAL Model GCO2D Gas Convection Oven is a single cavity oven, featuring a solid state temperature control and 1-hour dial timer.
– 4 – INSTALLATION CODES AND STANDARDS In the United States of America: 1. State and local codes. 2. National Fuel Gas Code, ANSI/Z223.1/NFPA #54 (latest edition). Copies may be obtained from The American Gas Association, Inc., Accredited Standards Committee Z223 @ 400 N.
– 5 – Assembling the Legs to the Single Oven The 4" (10 cm) or 6" (15 cm) legs are packed inside the oven during shipment and must be installed on the bottom of the oven. Place the oven on its left side, being careful to avoid scratching the finish.
– 6 – LEVELING Once the oven is in its permanent position, place a carpenter's level on the oven rack. If the oven is installed on legs, turn the adjustable feet in or out to level oven front-to-back and side-to-side.
– 7 – GAS CONNECTION Gas supply connections and any pipe joint compound must be resistant to the action of propane gases. The oven is provided with a regulator integral to the gas solenoid valve, and requires no regulator external to the device. A gas shutoff valve is supplied with each oven and is located at the bottom of the control panel.
– 8 – PL-52225 ON HEAT IGNITION TIMER ON OFF GAS VALVE GAS VALVE THERMOSTAT TO SHUT OVEN OFF PLACE MASTER SWITCH IN "OFF" POSTION TURN GAS VALVE OFF TO SHUT OVEN OFF PLACE MASTER SWITCH .
– 9 – LIGHTING THE GCO2D OVEN Open the manual valve. Turn the MASTER switch ON and turn the thermostat to its maximum setting. Both the ON and HEAT lights should be lit.
– 10 – CONTROLS — MODEL GCO2C Built before October 1999 (Fig. 6) Fig. 6 THERMOSTAT CONTROL Temperature Display (When not timing product). Displays set cook temperature while the light in the Roast Button is lit. Will be overridden to display actual cavity temperature for 8 seconds when Thermometer Button is pushed.
– 11 – Roast Button Light (If On and not timing product, indicates the roast mode is selected). • The displayed temperature settings will be for the roast temperature except when the Thermometer Button is lit. • Rotating the Thermostat Knob will change the roast set temperature.
– 12 – Gentle Bake Button Selects the gentle bake time setting. A roast time must first be set. The gentle bake time can then be set at the roast time value or less. The gentle bake time will be the portion of roast time to operate in the gentle bake mode.
– 13 – BEFORE FIRST USE Before using the oven for the first time, it must be "burned in" to release any odors that might result from heating the new surfaces in the chamber. 1. Using a clean damp cloth, wipe the inside of the oven, including the racks.
– 14 – 1 2 SET PRIMARY SECONDARY MENU SELECT MODE R & H READY OVEN HEA TING OVEN POWER ROAST & HOLD ON ON NO IGNITION OFF OFF COOL OVEN MENU RACK 3 4 5 PL-53543 6 5 ST ART STOP 4 3 2 1 CONTROLS — MODEL GCO2C Built after October 1999 Always displays [HR:Min] when setting the time.
– 15 – MANUALLY SETTING THE TEMPERATURE AND COOK TIME To Set the Temperature • Press the SET button. Press the TEMPERATURE button; StPt displays to indicate Setpoint. • Use the Up and Down Arrow keys to increase or decrease the displayed Temperature value.
– 16 – Always Set the Temperature Before Setting the Time • Press the SET button. Press the TEMPERATURE button; StPt displays. Use the Up and Down Arrow keys to increase or decrease the Temperature. To save, press the SET button again. At startup, the display will initially show a GROWING BAR .
– 17 – ROAST AND HOLD OPERATION — GCO2C OVEN Roast and Hold cooks the product in two stages. During First Stage Cooking, the oven temperature is regulated by the Roast thermostat for the amount of time set on the Timer. After the lapsed time counts down to 00:00, Second Stage Cooking begins.
– 18 – CLEANING Disconnect the electrical power to the machine and follow lockout / tagout procedures. Clean outside of the oven daily by wiping with a clean damp cloth. Clean porcelain oven interior daily with soap or detergent and water. Rinse thoroughly and wipe dry with a soft clean cloth.
– 19 – FOR BEST RESULTS Product to be cooked should be centered on the oven rack, and the racks should be spaced evenly inside the oven. It is best not to rotate the product or open the door during the cooking cycle. Preheat the oven to 50 F° (28 C°) higher than desired cooking temperature.
– 20 – FORM 30975 Rev. D (12-07) PRINTED IN U.S.A. MAINTENANCE The oven and its parts are hot. Use care when operating, cleaning or servicing the oven. Disconnect the electrical power to the machine and follow lockout / tagout procedures. LUBRICATION The fan motor comes with sealed bearings and requires no lubrication.
An important point after buying a device Vulcan-Hart GCO2C ML-114571 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart GCO2C ML-114571 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart GCO2C ML-114571 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart GCO2C ML-114571 you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart GCO2C ML-114571 will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart GCO2C ML-114571, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart GCO2C ML-114571.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart GCO2C ML-114571. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart GCO2C ML-114571 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
