Instruction/ maintenance manual of the product GCO2C Vulcan-Hart
Go to page of 20
GCO2D & GCO2C GAS CONVECTION OVENS MODEL GCO2D ML-114569 GCO2C ML-114571 VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 FORM 30975 Rev.
– 2 – IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED.
– 3 – T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 4 – Installation, Operation, and Care of GCO2D & GCO2C GAS CONVECTION OVENS KEEP THIS MANUAL FOR FUTURE USE GENERAL The GCO2D Gas Convection Oven is a single cavity oven and features a solid state thermostat, 1-hour dial timer, and five racks as standard equipment.
– 5 – INSTALLATION CODES AND STANDARDS In the United States, Vulcan gas ovens must be installed in accordance with: 1) State and local codes; 2) National Fuel Gas Code, ANSI-Z223.
– 6 – REAR OF TOP OVEN KNOCK OUT WELDED PLATE FOR FLUE EXTENSION INSTALLATION BOTTOM LOCATING STUDS PL-52992 FRONT OF TOP OVEN ASSEMBLING STACKED OVENS Determine which oven will be on the bottom and place it on its left side, being careful to avoid scratching the finish.
– 7 – Do not turn the power supply on until after the gas connections have been made and checked for leaks. A T A D L A C I R T C E L EA T A D L A C I R T C E L E A T A D L A C I R T C E L E A T A.
– 8 – PL-52225 ON HEAT IGNITION TIMER ON OFF GAS VALVE GAS VALVE THERMOSTAT TO SHUT OVEN OFF PLACE MASTER SWITCH IN "OFF" POSTION TURN GAS VALVE OFF TO SHUT OVEN OFF PLACE MASTER SWITCH .
– 9 – LIGHTING THE GCO2D OVEN Open the manual valve. Turn the MASTER switch ON and turn the thermostat to its maximum setting. Both the ON and HEAT lights should be lit.
– 10 – CONTROLS — MODEL GCO2C Built before October 1999 (Fig. 6) Fig. 6 THERMOSTAT CONTROL Temperature Display (When not timing product). Displays set cook temperature while the light in the Roast Button is lit. Will be overridden to display actual cavity temperature for 8 seconds when Thermometer Button is pushed.
– 11 – Roast Button Light (If On and not timing product, indicates the roast mode is selected). • The displayed temperature settings will be for the roast temperature except when the Thermometer Button is lit. • Rotating the Thermostat Knob will change the roast set temperature.
– 12 – Gentle Bake Button Selects the gentle bake time setting. A roast time must first be set. The gentle bake time can then be set at the roast time value or less. The gentle bake time will be the portion of roast time to operate in the gentle bake mode.
– 13 – BEFORE FIRST USE Before using the oven for the first time, it must be "burned in" to release any odors that might result from heating the new surfaces in the chamber. 1. Using a clean damp cloth, wipe the inside of the oven, including the racks.
– 14 – 1 2 SET PRIMARY SECONDARY MENU SELECT MODE R & H READY OVEN HEA TING OVEN POWER ROAST & HOLD ON ON NO IGNITION OFF OFF COOL OVEN MENU RACK 3 4 5 PL-53543 6 5 ST ART STOP 4 3 2 1 CONTROLS — MODEL GCO2C Built after October 1999 Always displays [HR:Min] when setting the time.
– 15 – MANUALLY SETTING THE TEMPERATURE AND COOK TIME To Set the Temperature • Press the SET button. Press the TEMPERATURE button; StPt displays to indicate Setpoint. • Use the Up and Down Arrow keys to increase or decrease the displayed Temperature value.
– 16 – Always Set the Temperature Before Setting the Time • Press the SET button. Press the TEMPERATURE button; StPt displays. Use the Up and Down Arrow keys to increase or decrease the Temperature. To save, press the SET button again. At startup, the display will initially show a GROWING BAR .
– 17 – ROAST AND HOLD OPERATION — GCO2C OVEN Roast and Hold cooks the product in two stages. During First Stage Cooking, the oven temperature is regulated by the Roast thermostat for the amount of time set on the Timer. After the lapsed time counts down to 00:00, Second Stage Cooking begins.
– 18 – The convection oven is a bit faster than conventional deck-type ovens; temperature settings are lower and cook times are shorter. Since recipes and foods are subject to many variations and tastes, the guidelines regarding times and temperatures in this manual are SUGGESTIONS ONLY.
– 19 – FOR BEST RESULTS Product to be cooked should be centered on the oven rack, and the racks should be spaced evenly inside the oven. It is best not to rotate the product or open the door during the cooking cycle. Preheat the oven to 50 F ° (28 C ° ) higher than desired cooking temperature.
– 20 – FORM 30975 Rev. C (Aug. 2000) PRINTED IN U.S.A. MAINTENANCE WARNING : THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING, OR PERFORMING ANY MAINTENANCE. WARNING : DISCONNECT THE ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE OVEN BEFORE PERFORMING ANY MAINTENANCE .
An important point after buying a device Vulcan-Hart GCO2C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart GCO2C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart GCO2C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart GCO2C you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart GCO2C will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart GCO2C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart GCO2C.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart GCO2C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart GCO2C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
