Instruction/ maintenance manual of the product 7096A1 ML-104500 Vulcan-Hart
Go to page of 16
7000 SERIES GAS OVENS MODEL 7018A1 ML-104491 7088A1 ML-104492 7888A1 ML-104493 7086A1 ML-104494 7016A1 ML-104495 7066A1 ML-104496 7019A1 ML-104497 7099A1 ML-104498 7999A1 ML-104499 7096A1 ML-104500 7098A1 ML-104501 7988A1 ML-104502 7998A1 ML-104503 MODEL 7019A1 VULCAN-HART COMPANY, P.
— 2 — IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED.
— 3 — T ABLE OF CONTENTS MODEL 7000 SERIES OVEN CONFIGURATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Bake Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
— 4 — MODEL 7000 SERIES BAKE OVEN CONFIGURATIONS 7086A1 7016A1 7066A1 7018A1 7088A1 7888A1.
— 5 — MODEL 7000 SERIES ROAST OVEN CONFIGURATIONS 7019A1 7099A1 Model 7999A1 not shown. MODEL 7000 SERIES COMBINATION BAKE & ROAST OVEN CONFIGURATIONS 7096A1 7098A1 7988A1 Model 7998A1 not shown.
— 6 — Installation, Operation and Care of VULCAN 7000 SERIES BAKE AND ROAST OVEN KEEP THESE INSTRUCTIONS GENERAL The manufacturer suggests that you thoroughly read this entire manual and carefully follow all of the instructions provided. Your Vulcan 7000 Series Bake and Roast Oven is produced with quality workmanship and material.
— 7 — INST ALLA TION UNPACKING Immediately after unpacking, check for possible shipping damage. If the oven is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. There may be a large label located on the front of the oven which reads, "Remove this label before operation.
— 8 — ASSEMBLY Legs If oven is to be mounted on legs, assemble legs to the oven. Tip oven back and install two front legs with bolts through bottom of oven base frame. Tip oven forward, block up back and install rear legs. Remove shipping harnesses from the burner area.
— 9 — These ovens can be mounted interchangeably starting with the largest section on the bottom. The factory shipping tags will be marked accordingly.
— 10 — GAS CONNECTIONS All gas supply connections and any pipe joint compound used must be resistant to the action of propane gases. The oven is equipped for a 3 / 4 " gas pipe connection. Pipe gas supply to the oven. Make sure the pipes are clean and free of obstructions, dirt and piping compound.
— 11 — ELECTRICAL CONNECTIONS WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING: APPLIANCES EQUIPPED WITH A FLEXIBLE ELECTRIC SUPPLY CORD ARE PROVIDED WITH A THREE-PRONG GROUNDING PLUG.
— 12 — OPERA TION WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE OVEN. CONTROLS (Fig. 4) Burner Valve — when opened, allows gas to flow to the oven burner. To open valve, turn knob counterclockwise; to close valve, turn knob clockwise.
— 13 — LIGHTING AND SHUTTING DOWN PILOT 1. Turn on main gas supply. 2. Turn burner valve ON and purge air from line. Turn burner valve OFF. 3. Wait 5 minutes, then turn burner valve ON and depress ignition button. Using a lit taper, ignite oven pilot (Fig.
— 14 — PREHEATING Set thermostat knob to desired temperature and allow oven to preheat for approximately 15 minutes before loading. LOADING OVEN 1. When using 2- or 4-deck sections that have one control for two compartments, load both compartments simultaneously.
— 15 — CLEANING WARNING: TURN OVEN OFF AND UNPLUG THE ELECTRICAL CORD (IF APPLICABLE) BEFORE CLEANING. Clean interior and exterior of oven daily with warm water and detergent solution.
— 16 — MAINTENANCE WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE OVEN. REPLACING OPTIONAL LAMPS WARNING: TURN OVEN OFF AND UNPLUG ELECTRICAL CORD BEFORE REPLACING LAMPS. Lamps are located in the top of the oven, centered at the back.
An important point after buying a device Vulcan-Hart 7096A1 ML-104500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart 7096A1 ML-104500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart 7096A1 ML-104500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart 7096A1 ML-104500 you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart 7096A1 ML-104500 will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart 7096A1 ML-104500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart 7096A1 ML-104500.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart 7096A1 ML-104500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart 7096A1 ML-104500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
