Instruction/ maintenance manual of the product 36L77R Vulcan-Hart
Go to page of 20
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791 SER VICE AND P AR TS MANUAL FOR ECONOLINE SERIES GAS REST AURANT RANGES MODELS: 36L77R, 36FL77R, 60L77R, 60FL77R, 160L.
– 2 – ECONOLINE SERVICE AND PARTS IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.
– 3 – ECONOLINE SERVICE AND PARTS SER VICE AND P AR TS MANU AL ECONOLINE SERIES GAS REST A URANT RANGE - INDEX PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE Your Vulcan Econoline Range is produced with quality workmanship and material. Proper installation, usage and maintenance of your range will result in many years of satisfactory performance.
– 4 – ECONOLINE SERVICE AND PARTS WARNING: THE RANGE AND ITS PARTS ARE HOT. BE VERY CAREFUL WHEN OPERATING, CLEANING OR SERVICING THE RANGE. CONTROLS (FIG. 1) Thermostat Dial — allows operator to regulate oven temperature from low to 500 ° F. Open Top Burner Valve Knob — regulates gas flow to top burners.
– 5 – ECONOLINE SERVICE AND PARTS Open Top Pilots 1. Remove all top section cover plates and griddles. 2. Turn main gas supply ON (all burner valve knobs should be in OFF position). 3. Begin from the left range top side. Light each indi- vidual pilot from front to rear across the entire range top section.
– 6 – ECONOLINE SERVICE AND PARTS Pilot Burner Adjustment (Grayson Safety Valve Shown) 1. Remove pilot adjusting cap. 2. Adjust pilot key to provide properly sized flame.
– 7 – ECONOLINE SERVICE AND PARTS THERMOSTAT (BJWA) To Adjust By-Pass Flame (Minimum Burner Flame): When oven reaches the temperature at which the dial is set, the oven control cuts down the flow of gas to the amount required to keep the oven at that temperature.
– 8 – ECONOLINE SERVICE AND PARTS OVEN CONTROL RECALIBRATION NOTE: Do not recalibrate oven control until the by-pass flame has been adjusted. The oven is a precision instrument. It is carefully cali- brated at the factory so that the dial settings match the actual oven temperatures.
– 9 – ECONOLINE SERVICE AND PARTS ORIFICE DATA OPEN TOP GRIDDLE BROILER OVEN GRIDDLE INPUT AT SEA LEVEL 15,000 15,000 10,000 35,000 PER BURNER (BTU'S) GAS TYPE NAT/PROP NAT/PROP NAT/PROP NAT/PROP SEA LEVEL TO 48/57 48/57 54/62 34/51 2000 FT. 2000 FT.
– 10 – ECONOLINE SERVICE AND PARTS TR OUBLESHOO TING OVEN PROBLEM PROBABLE CAUSES Too much bottom heat. 1. Insufficient heat input. 2. Overactive flue. Uneven bake. 1. Too low temperture. 2. Improper operation. Side burning. 1. Improper bypass setting.
– 11 – ECONOLINE SERVICE AND PARTS REPLA CEMENT P ARTS LIST ECONOLINE GAS RESTAURANT RANGE REPLACEMENT PARTS LIST AND PHOTOS REPLACEMENT PARTS ORDERING The following information must accompany a replacements parts order or it cannot be filled. A. Model and style or serial number.
– 12 – ECONOLINE SERVICE AND PARTS PART NO. ITEM NO. DESCRIPTION 36L77R 60L77R 160L77R 260L77R 1 PILOT BRACKET 413302-1 413302-1 413302-1 413302-1 +2 REAR BURNER ASSEMBLY (NAT) 409643-G7 409643-G7.
– 13 – ECONOLINE SERVICE AND PARTS PART NO. ITEM NO. DESCRIPTION 36L77R 60L77R 160L77R 260L77R 6 BURNER VALVE HANDLE 413157-1 413157-1 14 LIGHTER VALVE 404193-2 404193-2 +15 BROILER BURNER VALVE (.
– 14 – ECONOLINE SERVICE AND PARTS PART NO. ITEM NO. DESCRIPTION 36L77R 60L77R 160L77R 260L77R 8 BRICK SET 407065-G1 407065-G1 407065-G1 14 PILOT VALVE (NS) 404193-2 404193-2 404193-2 18 THERMO. BULB - SHIELD (NS) 411655-2 411655-2 411655-2 19 THERMO.
– 15 – ECONOLINE SERVICE AND PARTS ITEM NO. DESCRIPTION PARTS NO. 36L77R 60L77R 160L77R 260L77R 92 RIGHT DOOR POST HANDLE 413416-1 1212 92A LEFT DOOR POST HANDLE 413416-2 1212 93 BELL CRANK PIN RS.
– 16 – ECONOLINE SERVICE AND PARTS PART NO. ITEM NO. DESCRIPTION 36L77R 60L77R 160L77R 260L77R +74 PILOT (NATURAL) 412787-1 412787-1 412787-1 412787-1 PILOT (PROPANE) 412787-2 412787-2 412787-2 41.
– 17 – ECONOLINE SERVICE AND PARTS PART NO. ITEM NO. DESCRIPTION 36L77R 60L77R 160L77R 260L77R 27 BELL CRANK 403956-1 403956-1 403956-1 403956-1 31 TURNBUCKLE & HOOKS 417865-1 417865-1 417865-.
– 18 – ECONOLINE SERVICE AND PARTS PART NO. ITEM NO. DESCRIPTION 36L77R 60L77R 160L77R 260L77R 33 SPLASHER BACK ASSEMBLY 413223-G1 413223-G3 413223-G3 413223-G5 SPLASHER BACK ASSEMBLY (SS) 413223-.
THIS P AGE INTENTIONALL Y LEFT BLANK.
THIS P AGE INTENTIONALL Y LEFT BLANK.
An important point after buying a device Vulcan-Hart 36L77R (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vulcan-Hart 36L77R yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vulcan-Hart 36L77R - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vulcan-Hart 36L77R you will learn all the available features of the product, as well as information on its operation. The information that you get Vulcan-Hart 36L77R will certainly help you make a decision on the purchase.
If you already are a holder of Vulcan-Hart 36L77R, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vulcan-Hart 36L77R.
However, one of the most important roles played by the user manual is to help in solving problems with Vulcan-Hart 36L77R. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vulcan-Hart 36L77R along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
