Instruction/ maintenance manual of the product VPC9132 Vista
Go to page of 12
Protos 3 Series Cameras Installation Instructions Read these instructions first! VPM8030 VPM8032 VPM8130 VPM8132 VPM8120 VPM8122 VPC9030 VPC9032 VPC9130 VPC9132 VPC9032/CM VPC9132/CM.
2 Installation Instructions INTRODUCTION Read all of these instructions. Use them to install your camera and have them available for its lifetime. If you have any problems, contact your agent. Note that not all cameras have all of the features described in this manual.
3 Installation Instructions PRODUCT SAFETY Installation and servicing is only to be carried out by suitably qualified and experienced personnel. Mains cameras contain hazardous voltages. Do not remove covers as there is a risk of injury or death by electric shock.
4 Installation Instructions CAUTIONS In order to avoid damaging the camera note the following points: 1) The camera has threaded mounting points on the top and bottom of the case. Only use a standard, photographic, mounti ng-bolt with a 1/4 20 UNC thread.
5 Installation Instructions CONTROLS A N D SWITCHES On the side of the camera is a hinged flap. The hinged flap covers various adjustment controls and function switches.
6 Installation Instructions CONTROLS A N D SWITCHES (4) Electronic Iris (EI) The Electronic Iris (EI) compensates for excessive light level by automatically adjusting the shutter speed. The electronic iris should be ON when using fixed or manual iris lenses.
7 Installation Instructions CONTROLS A N D SWITCHES output for a typical scene. The level should not be adjusted unless absolutely necessary . (1 1a) Supply V oltage T erminals This terminal accept s an 1 1-40 VDC or 14-30 V AC at 50Hz (CCIR/P AL) or 60Hz (EIA/NTSC) power source.
8 Installation Instructions LENS SELECTION Suitable lens types are C and CS mount in fixed iris, manual iris, auto iris or direct drive versions. Sizes are shown below . Cameras are factory set for CS mount lenses. If using a C mount lens, rotate either of the back focus screws approximately 30 turns anticlockwise before fitting the lens.
9 Installation Instructions FOCUS ADJUSTMENT Auto Iris and Direct Drive Lenses Fully open the iris by covering the lens with a suitable neutral density (ND) filter. Set the lens focus to infinity . View an image greater than 7 feet (2 meters) away . Focus the image using the back focus screw.
10 Installation Instructions.
11 Installation Instructions.
HB-PROTOS3D-6 Issue 6 04/02 Norbain SDL Limited Norbain House, Eskdale Road, Winnersh Triangle, Wokingham, Berkshire RG41 5TS Norbain SDL Limited reserve the right to make changes to the product and s.
An important point after buying a device Vista VPC9132 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vista VPC9132 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vista VPC9132 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vista VPC9132 you will learn all the available features of the product, as well as information on its operation. The information that you get Vista VPC9132 will certainly help you make a decision on the purchase.
If you already are a holder of Vista VPC9132, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vista VPC9132.
However, one of the most important roles played by the user manual is to help in solving problems with Vista VPC9132. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vista VPC9132 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
