Instruction/ maintenance manual of the product T9700 Vision Fitness
Go to page of 43
.
T ABL E OF CONT ENTS SECT ION 1: M A INTEN AN CE PROCEDURE MAINTENANCE CHECK LIST TENSIONING T HE BEL T PROCED URE DECK RE-W AXING PROCEDURE CLEAN TH E GROOVES PROCEDURE LUBRIC.
SECTI ON 1 MAINTEN ANCE PROCEDU RE.
PREVENTIVE MAINTENANCE SCHEDULE VISION TREADMILL Item Daily Weekly Monthly Quarterly Biannual Annual Console Mounting Bolts Inspect Frame Clean Inspect Running Belt T op Clean (V acuum) Inspect #3 Car.
TENSIONING THE BEL T Caution: Over-tightening of the roller w ill severely shorten the life of the belt and may cause further damage to other compon ents. Running Bel t: If when you plant your foot on the belt, you can feel a slipping sensation then the belt has stretched and is slipping across the rollers.
DECK RE-W AXING PROCEDURE Frequency: Every 1 mont h. LUBE Name: DOW CORNING 350 SILICON Procedure: 1. Loosen the tension bolts at both ends. 2. Pull the belt w ith your lef t hand and apply the silicon in the deck w ith your right hand. (The volume of silicon applied is about 25C C.
CLEAN THE GROOVES PROCEDURE Frequency: Every 3 mont hs. Procedure: 1.Remove the drive belt and check the grooves in belt for dirt or dust and clean it. 2.Check the grooves in motor pulley for di r t or dust and clean it. 3Check the grooves in roller pulley for dirt or dust and clean it.
LUBRICA TING THE AIR SHOCK Frequency: Every 6 mont hs. Procedure: 1. Fold up the frame by using the deck-locking lever . 2. Add the lubricating oil on the shaf t of the air shock. 3. Lift the fra me up and down, repeating this several times to allow the l ubricati ng oil blend into air shock.
SECTI ON 2 WIRING DIA GRAM INSTRUC TION.
T9700( TM51D/E) MCB WIRING( FOR 1 10V / 22 0V) T1---- -Motor w ir e (black) T2---- -Motor w ir e (r ed) T3---- -D1 of on/off sw itch T4---- -D3 of on/off sw itch T5---- -20-pin con.
T9600HRT (COMFO R T)/T9 600HR T/T9500HR T/T9 450HR T/T935 0/T9300 MCB WIRING(F OR 1 10 V / 220V) T1---- -Motor w ir e (black) T2---- -Motor w ir e (r ed) T3---- -D1 of on/off sw itch T.
T9200/T9250 MCB WIRIN G(FOR 1 10V / 2 20V) T1---- -Motor w ir e (black) T2---- -Motor w ir e (r ed) T3---- -D1 of on/off sw itch T4---- -D3 of on/off sw itch T5---- -8-pin console .
SECTI ON 3 CONSOLE E NGIN EERING MODE GUIDE.
T9700(T M51D/E) TREADMILLS (for Soft w are V er . 2.5) Apply to : 1. VISION T9700/T9600 serise treadmail . 2. 2004 year T9700 serise treadmail. 3. 2004 year for ID How to enter into the engineering mode? 1. Press & Hold both “ELEV A TION UP” and “SPEED DOW N” a t the sam e time for 3-5 sec.
KEY BEHALE FUNCTION key name function SELECT To Store up the parameter SPEED UP Add this show parameter of speed and elevati on SPEED DOWN Decrease th is sho w parameter of speed and elevation STOP Pr.
P13 ELV DIR Change the inc line altitude 255 0 255 P14 ELV ERRS Change the al ti tude error switc h, 0=OFF, 1=ON 0 0 1 P15 SCROLL set the change display show le tter speed 7 1 255 P16 LUBE HRS Ac cumu.
T9600HR T(COMFOR T)/T9 600HR T/T95 00HR T/T9450HR T/ T9350/T9300 TREADMILLS ( fo r Software V er . 5.9 ) Appl y t o : 1. VISI ON T93 00/T9350/T9400/T9450/T9500 serise treadm ail. 2. 2004 y ear T9300/T9350/T9450/T9500/T9600 seri se treadmail. 3. 2004 y ear T9350/T9450/T9500 for ID How to enter into the engineering mode? 1.
KEY BEHALE FUNCTION key name function SELECT T o S tore up the parameter SPEED UP Add this show parameter of speed and elevation SPEED DOWN Decrease this show parameter of speed and elevation ELEV A T.
Appendix (1) SOU=SOURCES P ARAMETER SCO=SCOPE P ARAMETER P6 P0 P1 P2 P4 P5 MODEL Metric/ English SET SOU SCO SOU SCO SOU SCO SOU SCO SOU SCO English 0 41 2~70 363 250~511 189 100~270 69 1~150 217 130~.
Metric 9 29 2~70 348 250~511 179 100~270 63 1~150 177 130~255 English 24 29 2~70 348 250~511 179 100~270 63 1~150 177 130~255 Metric 34 29 2~70 348 250~511 179 100~270 63 1~150 177 130~255 English 10 .
Remarks : 1. If set address P6 model is T9450(Configuration Number 6/7/23/33) machine the address P1 1 will automatic set to 7,bec ause runnin g band the depth is 4.4mm. 2. If you want to the clean accum ulate ti me and distance, please press the "ELEV A TION UP and DOWN" for 5 sec of user mode.
T9200/T9250 TR EADMILLS ( fo r Soft w ar e V er . S706) How to enter into the engineering mode? 1. Press & Hold both “EL EV A TION UP” and “SPEED DOWN” at the same time for3-5 sec. Then, the dot vision display first will show VERSION ” foll ow show ENG 1 ” 2.
ENG1 Remark s: 1. If you want to the clean accum ulate time and distance, please enter engineering mode select “ENG1” enter , pl ease enter P9 (Acc umulate Tim e) or P10 (Accum ulate D istance) hold “ELEV A TION DOWN and SPEED UP” for 3 ~5 sec.
SECTI ON 4 MCB LED INSTRUCTIONS.
MC B L ED In dica tion Note: Use a multi-meter to test the pow er socket. 1 10v mode: 95 v 140v 220v mode: 21 0v 250v Note: F or MCB (Low er-board) Note: For PCB (Upper.
MC B L ED In dica tion Note: over 26 A mp s when lit Note: a control command from the PCB to the MCB Light- W hen lit, indicates the Hi gh Power Direct Current supply f or the m otor (B+) is online. T his light will remain lit f or a period of time after power has been removed from t he MCB.
MC B L ED In dica tion Note: the incline is being commanded up Note: the incline is being commanded dow n Light- Indicates th e PCB is commanding the incline motor to move up. If the User is commanding the incline to inc rease and this light is not lit, check cabling, verif y proper PCB o peration and replace it if either is defective.
PWM MCB LED C HA RT NO. AC +18V +1 1V MTR I-LIMIT PWM UP DN 1 OFF OFF OFF OFF OFF OFF OFF O FF 2 ON OFF OFF OFF OFF OFF OFF O FF 3 ON ON OFF ON OFF OFF OFF O FF 4 ON OFF ON OFF OFF OFF OFF O FF 5 ON O.
MCB LED-AIDED TR OUBLESHOOTING CHART NO. PROBLEM/RESUL T CORRECT IVE ACTION 1 No operation of MCB or PCB V erif y connections, power switch, circuit breaker and fuse 2 No operation of MCB or PCB Check fuse F1 3 PCB will not power up R eplace MCB 4 PCB will power up but t he MCB will not operate V erify adequate line vo ltag e.
SECTI ON 5 TROUBL ESHOOTINGS.
No display on console Possible caus es: 1. Breaker is damage d. 2. ON/OFF sw itch is damaged. 3. MCB is da maged. 4. 6-pin console cable is damaged. 5. PCB is damaged. Fix: 1. ( refer to “MCB LED la y out & i ndication”……SECTION 6) V erify if LED 1 15vAC(AC) is lit.
Running speed is not stable Possible caus es: 1. A C power voltage is too low . 2. T ension of drive belt or running belt is too loose. 3. P oor adjustment of MCB. 4. M CB is damaged. 5. M otor is damaged. Fix: 1. Check the power volt age by using volt age-meter to see if it is w ithin 120 V 15% or 230V 15 %.
T readmill starts to run by itself Possible caus es: 1. T he console cable is broken. 2. P CB is out of order . 3. M CB is out of order . Fix: 1. Replace the console cable w ith a new one. 2. Replace the PCB. 3. Replace the MCB. All or some of the keys on console do not work Possible caus es: 1.
Noises generated under motor cover Possible caus es: 1. The running belt tension is adjusted too tight. 2. The bearing of front roller is not installed correctly . 3. Dirty grooves of drive belt. 4. The motor is damaged. Fix: 1. Adjust the belt tension so that the belt does not start slippin g and then check if the noise has disappeared.
T readmill will not start Possible caus es: 1. MCB is da maged. 2. 8-pin console cable is damaged. 3. PCB is damaged. 4. Motor is damaged. Fix: Open motor cover , v erify wire connection MTR1 and MTR2 on the MCB then plug in the power cord and turn on the power switch.
Incline function does n ot work Possible caus es: 1. The 8-pin console cable is damaged . 2. Incline motor is damaged. 3. PCB is damaged. 4. MCB is damaged.
Heart-Rate-Con trol fu n ction does no t work Possible caus es: 1. Tr ansmitter does not cont act w ith us er's che st ver y well. 2. Tr ansmitter(Polar-bel t) is at low battery statu s. 3. Tr ansmitter(Polar-bel t) is damaged. 4. Heart-rate-control board is damaged.
Error Messages on the Console T9 700 (TM51D/E) Err or code definition Error Definition E4 Inc line motor parameter over the set E5 Incline motor not to move ment E6 Incline motor the signal not answer E7 Speed over the 2. 0 mph km/h Error Message "E4" : Please enter the engineer mode to execute the AUTO-CA L MODE.
T9600HR T (COMFOR T)/T9600HR T/T950 0HRT /T9450HR T/T9350/ T9300 Error code definition Error Definition E4 Incline motor para m et er over the set E5 Incline motor not to m ove m ent E6 Incline motor .
T9200/T9250 Error code d efinition Erro r code def inition Error Definition E2 Incline motor problem Erro r Mes sage " E2" : 1. Please check the incline m otor cable whe ther to inset MCB. 2. Check the console signal whether tra nsmission to MCB, y ou can refer to MCB LED UP and DOWN.
Revision: 1.0 Date: 1999-09- 01 SECTI ON 6 SOFTW AR E UPGRADE PROC EDURE.
Revision: 1.0 Date: 1999-09- 01 VISION SERI ES TRE A DMI LL SO FT WA RE UPGRADE SOP A. Service T ools & A cce ssories: 1. Computer (Notebook is preferred) 2.
Revision: 1.0 Date: 1999-09- 01 B. Step s : 2. Connection cable s & s hort pin is ready. 3. Turn ON t he power s w itch. 4. Find out the software version file in the computer and then actuate/open the file b y “click” the mouse twice. 5. The computer wi ll be turned into DOS mode, and run the ins tallation work.
An important point after buying a device Vision Fitness T9700 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vision Fitness T9700 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vision Fitness T9700 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vision Fitness T9700 you will learn all the available features of the product, as well as information on its operation. The information that you get Vision Fitness T9700 will certainly help you make a decision on the purchase.
If you already are a holder of Vision Fitness T9700, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vision Fitness T9700.
However, one of the most important roles played by the user manual is to help in solving problems with Vision Fitness T9700. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vision Fitness T9700 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center