Instruction/ maintenance manual of the product ST250 Vision Fitness
Go to page of 16
Assembly Guide ST250 LEG PRESS.
2 T o avoid possible damage to this Leg Press, please follow these assembly steps in the correct order . Before proceeding, find yo ur new Leg Press’ serial number located on the back of the base tube (1b), and enter here: Refer to this number when calling for ser vice, and enter this serial number on your W arranty Card and in your own records.
3 5 STEP 3 STEP 2 STEP 4 STEP 6 STEP 7 STEP 8 STEP 1 STEP.
4 19mm Wrench 6mm L-Shaped Wrench (2) TOOLS & P AR TS INCLUDED P AR TS BOX Color-coded Hardware Bags Owner’ s Guide Assembly Guide W arranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench.
5 ORANGE BAG BLUE BAG HARDW ARE INCLUDED M10 x 1.5P Nut Quantity: 12 10.5 x 18 x 2T Flat W asher Quantity: 16 M10 x 1.5P x 60L Carriage Bolt Quantity: 2 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 8 M10 x 1.5P x 100L Bolt Quantity: 4 M10 x 1.5P Nut Quantity: 3 M10 x 1.
6 PINK BAG GREEN BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 2 M10 x 1.5P Nut Quantity: 2 M6 x 1P x 15L Bolt Quantity: 3 90mm Shaft Quantity: 1 10.5 x 30 x 2T Flat W asher Quantity: 2 165mm Shaft Quantity: 1 SW6.1 x 12.2 x 1.5T Spring W asher Quantity: 3 6.
7 BLACK BAG 15x33L Shoulder Bolt Quantity: 1 U Bracket Quantity: 1 M12 Slotted Bolt Quantity: 1 M10 x 1.5P Nut Quantity: 1 10.5 x 18 x 2T Flat W asher Quantity: 1 SW10.
8 1 STEP • If you aren’t adding any weight plates to the stack, skip this step and proceed to Step 2. • Y our unit is equipped to handle 21-ten pound plates (20 plates and the header plate).
9 1b 1a 1d 1c 1e 1e 2 STEP • Attach the connecting brace (1a) to the empty holes on the left floor support of the base unit ( ST200 ). Connect with two carriage bolts (M10x1.5Px60L), two fl at (10. 5x18x2 T) & s p r i n g (SW10.2x18.4x2.5T) washers, and two nuts (M10x1.
10 3 STEP • Lay the seatback (2a) face down. Mate the seatback support (2b) to 2a. Make sure the holes of 2b are pointing up towards the top of the seatback. Securely fasten four bolts (M10x1.5Px30L) into the seatback using a 6mm L-shaped wrench. Thread the pull pin partially into the opening of 1b.
11 4 STEP • Insert the lever ar m (3a) into the triangular structure at the front of 1b. When the holes are lined up, insert the 90mm shaft along with a flat (17 x25x 1.5 T) washer through the lower end of 3a and fasten with a flat (10.5x30x2T) washer and a bolt (M10x1.
12 5 STEP • If you already have the base unit assembled with cable #2 and are adding the leg press to it, follow this instruction, other wise proceed to Step 6: Unscrew the nuts and bolt that attaches cable #2 to the rear termination tube (6b of base unit), using a 19mm wrench.
13 6 STEP • Attach the pulley structure (U) to the bottom rear floor support of the base unit with three bolts (M6x1Px15L), three f l a t (6.4x14x1T), and three spring (SW6.
14 7 STEP • Begin routing cable #6 with the end opposite the steel ball end. Feed the cable over pulley R, under S, around T , and under U. Unscrew the nut from the slotted bolt (M12). With the threads of the bolt facing up, slide cable #6 through it and reattach the nut.
15 8 STEP • Attach the decals according to the diagram below . DECALS PINCH POINT SAFETY DECAL PLACEMENT.
500 South CP Avenue • P .O. Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 www .visionfitness.com © 2005 Vision Fitness.
An important point after buying a device Vision Fitness ST250 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vision Fitness ST250 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vision Fitness ST250 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vision Fitness ST250 you will learn all the available features of the product, as well as information on its operation. The information that you get Vision Fitness ST250 will certainly help you make a decision on the purchase.
If you already are a holder of Vision Fitness ST250, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vision Fitness ST250.
However, one of the most important roles played by the user manual is to help in solving problems with Vision Fitness ST250. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vision Fitness ST250 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
