Instruction/ maintenance manual of the product ST200 Vision Fitness
Go to page of 20
Assembly Guide ST200 FUNCTIONAL TRAINER.
2 T o avoid possible damage to this Functional T rainer , please follow these assembly steps in the correct order . Before proceeding, find your new Functional T rainer serial number located on the ba.
3 2 STEP 1 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 STEP 8 STEP 9 STEP.
4 19mm Wrench 6mm L-Shaped Wrench TOOLS & P AR TS INCLUDED P AR TS BOX Color-coded Hardware Bags Owner’ s Guide Assembly Guide W arranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench.
5 ORANGE BAG BLUE BAG HARDW ARE INCLUDED SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 4 10.5 x 18 x 2T Flat W asher Quantity: 8 M10 x 1.5P Nut Quantity: 6 M10 x 1.5P x 60L Bolt Quantity: 4 M10 x 1.5P x 25L Bolt Quantity: 2 M6 x 1P x 15L Bolt Quantity: 2 M10 x 1.
6 PINK BAG GREEN BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 2 M10 x 1.5P Nut Quantity: 2 M10 x 1.5P x 60L Bolt Quantity: 2 M10 x 1.5P x 25L Bolt Quantity: 8 SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 6 10.5 x 18 x 2T Flat W asher Quantity: 4 M10 x 1.
7 BLACK BAG YELLOW BAG HARDW ARE INCLUDED 10.5 x 18 x 2T Flat W asher Quantity: 6 M10 x 1.5P Nut Quantity: 4 M10 x 1.5P x 60L Bolt Quantity: 2 M6 x 1P x 50L Bolt Quantity: 2 M12 Slotted Bolt Quantity: 3 6.4 x 14 x 1T Flat W asher Quantity: 2 M6 x 1P Nut Quantity: 2 Karabiner Quantity: 5 SW10.
8 RED BAG HARDW ARE INCLUDED SW10.2 x 18.4 x 2.5T Spring W asher Quantity: 10 M10 x 1.5P x 25L Bolt Quantity: 10.
9 1d 1b 1e 1c 1a 1 STEP • Lay the back side of the rear vertical upright (1a) down onto the floor . The threaded bolt ends will be pointing up. Place the center floor support (1b) over the threaded ends. Attach a flat (10.5x18x2T) and spring (SW10.2x18.
10 2 STEP • Thread pull pins par tially onto 2a (Qty . 1) and 2c (Qty . 2). • Lay the front center vertical (2f) on the floor . Slide the seat suppor t structure (2a) over the open end of 2f. NOTE: Y ou must pull the pull pin out (2b) and hold it when sliding over 2f.
11 3 STEP • Place the top front structure (3a) on top of 2f and attach with two bolts (M10x1.5Px60L), two flat (10.5x18x2T) washers, and two nuts (M10x1.5P). Tighten fasteners with a 6mm L-shaped wrench and a 17mm wrench. • Attach the seat (3b) up through the bottom of 2a with four bolts (M10x1.
12 4 STEP • Place the bottom of the left oval upright (4a) onto the protruding bolts of 1d. NOTE: Make sure the 27 holes of 4a are on the outside. Mate the hole in the top of 4a with the top hole of 3a. Attach and tighten one flat (10x30x2T) & spring (SW10.
13 5 STEP • If you are adding 15 weight plates to the base unit, proceed as follows. If you are adding 20 weight plates, the steel tube spacer (5a) will not be used. • Place two rubber weight plate bumpers (5b) over the 0.75” holes of 5a. Place 5a over the holes of 1b.
14 6 STEP Wrap one end of cable #1 around pulley A. On the right side of the unit, place it through pulleys B, C, D of 6a, and E. Remove the nuts from 2 slotted bolts (M12) (see diagram below). With the threads pointing down on the slotted bolt (M12), slide the end of cable #1 through it.
15 7 STEP If assembling just the base unit ( ST200 ), proceed as follows. If assembling with the leg press ( ST250 ), refer to Step 5 of the leg press assembly guide. Slide the small steel end of cable #2 through pulleys F and G. Remove the nuts from the slotted bolt (M12).
16 8 STEP • Remove the slotted bolts (8a) located on the inside of the right and left handles of uprights 4a & 4b. Remove the nuts from the bolts. Slide the small steel end of cable #3 through pulleys H & I. Continue through pulleys J thru P .
17 9 STEP • Place the rear hole of the left decorative cover (9a) over the threaded post on the left side of structure 5e. Loosely attach a spring (SW10.2x18.4x2.5T) washer and a bolt (M10x1.5Px25L). Thread two bolts (M10x1.5Px25L) and two spring (SW10.
18 General Warning/Safet y Decal Placement Weight Plate Sticker Placement 10 STEP • Attach the decals according to the diagram below . DECALS.
19.
500 South CP Avenue • P .O. Box 280 • Lake Mills. WI 53551 toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373 www .visionfitness.com © 2005 Vision Fitness.
An important point after buying a device Vision Fitness ST200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vision Fitness ST200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vision Fitness ST200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vision Fitness ST200 you will learn all the available features of the product, as well as information on its operation. The information that you get Vision Fitness ST200 will certainly help you make a decision on the purchase.
If you already are a holder of Vision Fitness ST200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vision Fitness ST200.
However, one of the most important roles played by the user manual is to help in solving problems with Vision Fitness ST200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vision Fitness ST200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
