Instruction/ maintenance manual of the product MF-105B Viper
Go to page of 29
Understanding and Using Your Moogerfooger MF-105B Bass MuRF TABLE OF CONTENTS Getting Started............................................3 Frequencies and Filters...............................5 The Bass MuRF’s Filters............................7 Envelope Generators.
Welcome to the world of Moogerfooger Analog Effects Modules! Your model MF-105B Bass MuRF is a rugged, profes- sional-quality instrument, designed to be equally at home on stage or in the studio.
GETTING STARTED Here are some simple instructions on how to quickly plug in and try out your MF-105B. 1. Unpack your MF-105B. Place it on a table while you become familiar with its features.
4. Connect an instrument cable from the LEFT/MONO jack to a line-level input on your amp or mixer. Turn the volume control on your amp down but not off. 5. Connect an instrument cable from your signal source to the AUDIO IN jack. You can feed virtually any instrument-level or line-level signal through your MF-105B.
instrument’s tone. You will hear the level of each of the 8 lters being turned up and down automatically in sequence by the Animation at a tempo determined by the RATE control. Note that changing the ENVELOPE control affects the shape that turns the lters up and down.
sound. Some types of lters (like the bass and treble controls on your sound system) have subtle, gentle effects on a sound’s timbre. Other types of lters have stronger and more dramatic effects, and are frequently used as vital elements in the music-making process.
The Bass MuRF’s FILTERS The Bass MuRF’s seven resonant lters have xed center frequencies and a shelving(lowpass) lter that has a xed cutoff frequency. These frequencies are shown on the legend underneath the lters’ sliders. Their frequencies are: 110 Hz(shelving lter), 160 Hz, 240 Hz, 350 Hz, 525 Hz, 775 Hz, 1.
3) Make sure the effect is on, and MIX is at 10. 4) Connect just the “left/mono” output to your amplication You may want to experiment with the panel controls and switches as we discuss each of the parameters. 5) Now, play a bright, sustained sound, preferably of low pitch into the Bass MuRF.
done two ways, depending on the position of the BANK slider switch. The switch, located below the PATTERN selector switch is labeled BANK A or B/LFO. When the slider is in the “A” position, the lters’ center frequencies can be shifted by an expression pedal (such as the Moog EP-1) or CV plugged into the LFO/SWEEP Jack.
ENVELOPE GENERATORS Now that we have explained the Bass MuRF’s lters, let’s proceed with some more denitions to explain the Animation function of the Bass MuRF. The term “Envelope” is used to describe the changes that occur to a musical sound, from its start to its end.
SEQUENCERS and PATTERN GENERATION A Sequencer is used to generate reoccurring rhythmic patterns, often by triggering sequences of notes in synthesizers or drum machines. However sequencers can be used for purposes other than triggering notes - they can be set up to create reoccurring changes of timbre as well.
The rows going from bottom to top are the individual lters. Illustrations of all the Patterns are in Appendix A, page 22. Return to the basic setting shown in gure 2, which features pattern 2. As you play your instrument through the Bass MuRF, pay attention to the sound of the effect and how it corresponds to gure 10.
and the transitions from lter to lter blurred, as the Attack and Decay become so long that the effect is crossfading from one lter to the next. 5) Finally, turn the ENVELOPE control up to 8. The effect now sounds “backwards” as the attack time is now smooth but fast, and the decay is abrupt.
THE AUDIO LEVEL CONTROLS AND MIXING The DRIVE control adjusts the signal level at the Bass MuRF’s circuit input. With this control you can set the right input level for virtually any instrument or line-level signal source. Turn this control counterclockwise for strong input signals, and clockwise for weaker sound sources.
Note that the odd-numbered lters are sent to the left channel, and the even-numbered lters are sent to the right channel. This allows for spreading a sound’s frequencies between two speakers, which adds a “spacious” feel.
MF-105B with external control signal sources in the Technical Information section on Pages 17 and 18. SOME TYPICAL SETUPS UPWARD STAIRCASE WITH RHYTHMIC VARIATION Here is a variation on the basic setting of gure 2 that shows off the abil- ity of the Bass MuRF to create rhythmic variations within the patterns.
TECHNICAL INFORMATION NOTE: The following information is intended for use by people who understand analog electronic circuitry and have enough practical experience to interconnect sophisticated electronic equipment correctly. X-FACTOR This setup shows off how long envelope times, in relation to the pattern’s rate, creates a morphing timbre.
The pedal cable should be shielded, with the shield connected to the sleeve terminal. See Figure 14. When connecting one or more pedal control input jacks to a source of external control voltage such as an analog synth or a MIDI-to-CV converter, you should use patch cords with tip-ring- sleeve phone plugs.
AUDIO PATH: The bypassed signal goes to the LEFT/ MONO output jack. Thus, when the Bass MuRF is bypassed, the signal at the LEFT/MONO output jack is the same as what your instrument is producing, and there is no signal at the right output jack. The MF-105B will not pass an audio signal unless power is applied to it.
MF-105B SPECIFICATIONS DESCRIPTION: Analog effects module incorporating two functions: 7 – band Resonant Filters and 1 - band Shelving (Lowpass) Filter and a 24- Pattern Sequencer triggering Volume Envelopes for 8 Filters. FRONT PANEL FEATURES: DRIVE rotary control - adjusts the gain of the audio input to the effect.
level; +8 dBm absolute maximum output level. Output impedance is 1,000 ohms. RATE, ENV, LFO/SWEEP, MIX, all of which are stereo ” jacks that accept Moogerfooger EP1 (or equivalent) expression pedals, or control voltages from two-circuit or three-circuit ” jacks.
APPENDIX A: THE Bass MuRF’s PATTERNS BANK A 1) No Animation 2) Upward Staircase 3) Repeater 4) X-Factor 5)Perpetual Motion.
10) Double Dip 9)Double X 8) Prime Number Rhythmicon 7) Rhythmicon 6) Arpeggiated Filters.
3) Down and Up 12) Slowbeat BANK B - with LFO 1) No Animation 2) Downward Staircase 11) Squiggly.
7) Arpeggiated Perpetual Motion 6) Asymmetry 5) Pyramid 4) Upward Cascade.
12) Big Beat 11) Breakbeat 10) Multi-groove 9)Folded Rhythmicon 8) Asymmetry 2.
APPENDIX B: Moog MuRF Pattern Step Adaptor (Sold separately) What it is: The MuRF Pattern Step Adaptor is a female to male 1/4” adaptor that attaches to your Moog (FS-1) footswitch cable and plugs into the tap/step input allowing the user to manually “step” through the patterns generated by the sequencer.
Notes:.
©2005 Moog Music Inc. MOOG MUSIC Inc. 2004-E RIVERSIDE DRIVE ASHEVILLE, NC 28804 Phone: (828) 251 0090 FAX: (828) 254 6233 Email: info@moogmusic.com WEB SITE: www.
An important point after buying a device Viper MF-105B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Viper MF-105B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Viper MF-105B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Viper MF-105B you will learn all the available features of the product, as well as information on its operation. The information that you get Viper MF-105B will certainly help you make a decision on the purchase.
If you already are a holder of Viper MF-105B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Viper MF-105B.
However, one of the most important roles played by the user manual is to help in solving problems with Viper MF-105B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Viper MF-105B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
