Instruction/ maintenance manual of the product WM1500 HTD-TE Vinotemp
Go to page of 21
WINE-MATE Cooling Unit Use & Care Manual WM1500 HTD, HTD-TE WM2500 HTD, HTD-TE V V i i n n o o t t e e m m p p I I n n t t e e r r n n a a t t i i o o n n a a l l C C o o r r p p .
- 1 - Important Safety Information • DO NOT PLUG IN UNTIL 24 HOURS AFTER DELIVERY. • DO NOT USE A GROUND FAUL T INTERRUPTER (GFI). • A DEDICATED 15 AMPCIRCUIT IS HIGHLY RECOMMENDED.
- 2 - TABLE OF CONTENTS Feature Description…………………………….……………..3 Installation Instruction……………………………………….
- 3 - Feature Description • WM1500HTD, HTD-TE and WM2500HTD, HTD-TE cooling units are designed and used to provide a subtle temperature between 50~65 °F for suitable space at a normal environment. • The refrigerated space will mainta in humidity of 50~70% RH even when the environment becomes dry and humid.
- 4 - Fig. 1.2 DIMENSIONS (in) The dimensions and capacity are specified as follows: Model Exhaust Cooling Capacity, CFM 55°F/75°F Bottle Capacity 55°F/75°F Electrical Weight 1500htd Rear Exhaust .
- 5 - Installation Instruction 1. Cabinet Location • Place the wine cabinet in a properly ventilated location. Otherwise, heat exhausted by the cooling unit will build up and it will not operate properly. • The exhaust area must not be clos ed space and must be ventilated.
- 6 - Fig. 2.2 COOLING UNIT MOUNTING Fig. 2.3 MOUNTING CUTOUT & GASKET LIPS (LOCATED AT THE CABINET).
- 7 - Fig. 2.3 TOP EXHAUST GASKET (LOCATED ON THE COOLING UNIT) • Cut a rectangular inside opening at the rear of the cabinet with the 1/4” clearance inwards to the width and height of the cooling unit. By not going through, leave 1/2” lip inside at the wa ll to place the gaskets (see Fig.
- 8 - Temperature Control & Humidity Adjustment 1. Temperature Setting • Set the temperature at 55 ° F for the optimum aging of wine • On initial start-up, the time required to reach the desired temperature will vary, depending on the quantit y of bottles, temperature setting and surrounding temperature.
- 9 - 2) Alarm Signals 2.1 Code Description 2.2 Alarm Recovery Probe alarms P1”, start a few seconds afte r the fault in the re lated probe; they automatically stop a few seconds afte r the probe restarts normal operation. Check connections before replacing the probe.
- 10 - 3.2 How to change the set-point 1. Push the SET key for more than 3 seconds to change the Set point value; 2. The value of the set point will be di splayed and the “°C” or “°F” LED starts blinking; 3. To change the Set value, push the keys or arrows within 10s.
- 11 - 7) Manual Defrost Push the DEF key for more than 2 se conds and a manual defrost will start..
- 12 - Care Guide I. Component Identification Fig. 4.1 Exploded View.
- 13 - II. Condenser Coil Cleaning • The condenser coil is on the ambient air intake side of the cooling unit. • Clean the condenser coil regularly .
- 14 - Troubleshooting This Troubleshooting Chart is not prepared to replace the training required for a professional refrigeration servic e person, not is it comprehensive Troubleshooting Chart Complaint Possible Causes Response 1.Unit not running a.
- 15 - blinking and beeping, temperature high or not cooling and running continually b. Room too large c. Ambient temperature too high d. Exhaust restricted e. Malfunctioning fans f. Improper evaporator or condenser airflow g. Dir ty Condens er h. Iced evaporator i.
- 16 - g. Capillary tube blockage system leakage g. Check fo r low side pressure 11.Water leak a. High humidity b. Air leak in wine cellar c. Evaporator air flow re striction d. Water passages restricted e. Drip tray leak a. Use drain line b. Check for any air leak c.
- 17 - Wiring Diagram Fig. 6.1 WIRING DIAGRAM Fig. 6.2 CALLING FE ATURE WIRING DIAGRAM.
- 18 - Customer Support If you still have problems, please contact us at: Vinotemp International 17631 South Susana Road Rancho Dominguez, CA 90221 Tel: (310) 886-3332 Fax: (310) 886-3310 Email: info@vinotemp.
- 19 - Warranty Thank you for choosing a Vinotemp cooling unit. Please enter the complete model and se rial numbers in the space provided: Model____________________ ____________________ _________________ Serial No._________________ ____________________ _________________ Attach your purchase receipt to this owner’s manual.
- 20 - is determined to be faulty and is within the twelve month warranty period VINOTEMP will, at its discret ion, repair or replace the unit and return it free of charge to the original retail customer. If the unit is found to be in good working order, or beyond the initial twelve month period, it will be returned freight collect.
An important point after buying a device Vinotemp WM1500 HTD-TE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vinotemp WM1500 HTD-TE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vinotemp WM1500 HTD-TE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vinotemp WM1500 HTD-TE you will learn all the available features of the product, as well as information on its operation. The information that you get Vinotemp WM1500 HTD-TE will certainly help you make a decision on the purchase.
If you already are a holder of Vinotemp WM1500 HTD-TE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vinotemp WM1500 HTD-TE.
However, one of the most important roles played by the user manual is to help in solving problems with Vinotemp WM1500 HTD-TE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vinotemp WM1500 HTD-TE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
