Instruction/ maintenance manual of the product DEV1200 Viking
Go to page of 8
READ AND SA VE THESE INSTRUCTIONS MODEL DEV1200 EXTERIOR MOUNTED VENTILA TOR FOR USE WITH VIKING VCWH, VICH, DBCV, DICV, DCWH, DCWL, DCWN, DTWS AND DCIH RANGE HOODS. 30" TO 66" WIDE, 9" TO 18" HIGH. W ARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1.
11" dia. hole 22" Guide hole (centered between studs) 22" 29½" 29½" 14 11 / 16 " 11 13 / 16 " 11 13 / 16 " 17" W all Stud W all Stud 11" dia. hole 17" 1¼" dia. hole 1¼" dia. hole 3 " Ø Ø Ø Ø REMO VE SIDING REMO VE SIDING Guide hole (centered between studs) 1.
1. Remove the cover and screws. 2. Attach an appropriate U.L. approved cable connector in the hole at the rear of the wiring box. 3. Remove roofing nails from shingles around the TOP and SIDES of the cutout area only.Carefully lift the shingles to allow the back flashing sheet on the ventilator housing to fit under them.
GREEN WHITE BLACK BLACK WHITE GREEN BLACK WHITE GREEN ROUGH-IN PLA TE LEAD ROUGH-IN PLA TE LEAD WIRING BOX EXTERIOR VENTILA TOR BLACK BLACK BROWN CAP ACITOR WHITE BLUE BLACK GREEN / YELLOW M GROUND LINE IN 120 V AC 60 HZ 10 A MAX. 99043051D F20221 1. Run 10" round steel ductwork, from exterior ventilator to the installation location.
VEUILLEZ LIRE CES DIRECTIVES ET LES CONSERVER MODÈLE DEV1200 VENTILA TEUR MONTÉ À L ’EXTÉRIEUR A VERTISSEMENT OBSERVEZ LES DIRECTIVES CI-DESSOUS DE MANIÈRE À RÉDUIRE LES RISQUES D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURES CORPORELLES. 1.
1. Choisissez un emplacement sur le mur extérieur. Assurez- vous qu’aucun poteau mural, tuyau ou câble ne passe au niveau de l’ouverture. 2. De l’intérieur, tracez un point de repère et percez un avant-trou centré entre les poteaux muraux .
1. Retirez le couvercle et les vis. 2. Fixez un connecteur de câble homologué U.L.dans l’ouverture à l’arrière du boîtier de câblage. 3. Retirez seulement les clous à toiture des bardeaux qui se trouvent sur le DESSUS et sur les CÔTÉS de la surface de découpe.
GREEN WHITE BLACK BLACK WHITE GREEN BLACK WHITE GREEN ROUGH-IN PLA TE LEAD ROUGH-IN PLA TE LEAD WIRING BOX EXTERIOR VENTILA TOR BLACK BLACK BROWN CAP ACITOR WHITE BLUE BLACK GREEN / YELLOW M GROUND LINE IN 120 V AC 60 HZ 10 A MAX.
An important point after buying a device Viking DEV1200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Viking DEV1200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Viking DEV1200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Viking DEV1200 you will learn all the available features of the product, as well as information on its operation. The information that you get Viking DEV1200 will certainly help you make a decision on the purchase.
If you already are a holder of Viking DEV1200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Viking DEV1200.
However, one of the most important roles played by the user manual is to help in solving problems with Viking DEV1200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Viking DEV1200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
