Instruction/ maintenance manual of the product HX270E Vertex Standard
Go to page of 32
H X 2 7 0 E HX270E VHF/FM Marine Handheld T ransceiver Owner's Manual.
T ABLE OF CONTENTS 1. GENERAL INFORMA TION ........ 2 2. ACCESSORIES .......................... 3 2.1 P ACKING LIST ................................... 3 2.2 OPTIONS ............................................ 3 3. BA TTER Y .........................
HX270E Page 1 Congratulations on your purchase of the HX270E ! Whether this is your first portable marine VHF transceiver , or if you have other ST ANDARD HORIZON equipment, the ST ANDARD HORIZON orga.
HX270E Page 2 1. GENERAL INFORMA TION 1.1 INTRODUCTION The HX270E is a submersible, miniature 5-Watt portable two-way VHF ma- rine transceiver . The transceiver has all allocated USA, international, or Canadian channels. It has an emergency channel 16 which can be immedi- ately selected from any channel by pressing the 16/9 key .
HX270E Page 3 2. ACCESSORIES 2.1 P ACKING LIST When the package containing the transceiver is first opened, please check it for the following contents: • HX270E Transceiver • FNB-83 7.
HX270E Page 4 3. BA TTERY The FNB-83 is a high performance rechargeable battery providing high ca- pacity in a comp act package. 3.1 BA TTERY CHARGING If the radio has never been used, or its charge is depleted, it may be charged by connecting the NC-88 battery charger (see figure 2 on page 5).
HX270E Page 5 3.3 USING THE NC-88 BA TTERY CHARGER 1. Install the supplied FNB-83 battery pack on the rear of the HX270E . Ensure that the transceiver is switched off. 2. Plug the NC-88 Overnight Charger into the AC line outlet, then insert the cable plug into the jack located on the side panel of the CD-26 Charger Cradle.
HX270E Page 6 3.5 BA TTERY SAFETY Battery packs for your transceiver contain Ni-MH batteries. This type of bat- tery stores a charge powerful enough to be dangerous if misused or abused, especially when removed from the transceiver .
HX270E Page 7 HX2 70E VOL Figure 3 Controls and Connectors 4. CONTROLS AND INDICA TORS NOTE This section defines each control of the transceiver . For detailed oper- ating instructions, refer to section 5 of this manual. Refer to Figure 3 for the location of the following controls, indicators, and connections.
HX270E Page 8 4.1 CONTROLS AND CONNECTIONS Antenna Connector The supplied CA T460 flexible antenna is attached here. POWER SWITCH/VOLUME CONTROL T urns the transceiver on and off, and adjusts the volume. PUSH-TO-T ALK ( PTT ) SWITCH Activates transmission.
HX270E Page 9 DW KEY Press the DW key , scan for voice communications on the priority chan- nel and another selected channel until a signal is received on either channel (Dual W atch). Refer to section “5.8 DUAL W A TCH” for details. H/L KEY T oggles the transmitter power level between High (5 Watt s), Medium (2.
HX270E Page 10 4.2 INDICA TORS Figure 4 Indicators Channel Display The operating channel is shown on the LCD in both the transmission and reception modes. A Indicator Signifies ship-to-ship channels in USA or Canadian mode (whose counter- part in the International mode is a public correspondence (marine operator) channel).
HX270E Page 11 MEM Indicator The channel is in the transceiver ’s “Scan Memory .” Battery Indicator When the battery charge is almost depleted, a “ ” icon will appear on the display . When this icon appears, it is recommended that you charge the battery soon.
HX270E Page 12 HX270E × Installing the Quick Draw Belt Clip 1. Connect the hanger to the rear of the HX270E , with the notch point- ing directly up, using the supplied screw ( Figure 6-a ). Use only the screw included with the clip to mount the clip to the back of the transceiver! 2.
HX270E Page 13 5.2 RECEPTION 1. Turn the POWER/VOLUME CONTROL knob clockwise to turn the trans- ceiver on. 2. Press the SQL key , then press the [ T ] key until the SQL level is 00 . 3. Turn up the POWER/VOLUME CONTROL knob until the noise or audio from the speaker is at a comfort- able level.
HX270E Page 14 5.3 TRANSMISSION NOTE Never key the transceiver without an antenna connected, as this may cause damage to the transceiver . 1. Perform steps 1 through 7 of the RECEPTION discussion above. 2. Before transmitting, monitor the channel and make sure it is clear .
HX270E Page 15 5.5 USA, CANADIAN, AND INTERNA TIONAL BANDS 1. T o change the operating band (channel set) of the transceiver , hold down the 16/9 key and press the DW key . The band will change from USA, to International, and to Canadian with each press.
HX270E Page 16 5.7 PROGRAMMABLE PRIORITY SCAN The priority scanning feature allows the radio to scan while also keeping watch on a particularly important “priority channel.” The following channels can be set as the priority channel: 16, 09, and Preset Channels 1 through 8 (Preset Channels are described in section 5.
HX270E Page 17 5.9 EMERGENCY (CHANNEL 16 USE) Channel 16 is known as the Hail and Distress Channel. An emergency may be defined as a threat to life or property . In such instances, be sure the transceiver is on and set to CHANNEL 16. Then use the following proce- dure: 1.
HX270E Page 18 Prior to making contact with another vessel, refer to the channel chart s in this manual, and select an appropriate channel for communications after initial contact. For example, Channels 68 and 69 of the U.S. VHF Charts are some of the channels available to non-commercial (recreational) boaters.
HX270E Page 19 5.13 PRESET CHANNELS (1 ~ 8): INST ANT ACCESS Eight user-assigned channels can be programmed for instant access. 5.13.1 Programming 1. Hold down the PRESET key , and press the [ S ] or [ T ] key (repeatedly , if necessary) until the desired channel number (from among the regular operating channels) is displayed.
HX270E Page 20 5.15 SETUP MODE The HX270E ’s Setup Mode allows a number of the HX270E operating pa- rameters to be custom-configured for your operating requirements. The Setup Mode is easy to activate and set, using the following procedure: 1. T urn the radio off.
HX270E Page 21 Key Continuous Off Normal S pecial 5.15.1 bEP (K EY B EEP ) Function : Enable/Disable the Keypad beeper . A vailable V alues : ON/OFF Default : ON 5.
HX270E Page 22 TROUBLESHOOTING CHART 6. MAINTENANCE The inherent quality of the solid-state components in ST ANDARD HORIZON radios will provide many years of continuous use.
HX270E Page 23 MEMO.
HX270E Page 24 VHF MARINE CHANNEL CHART CH TX RX Remarks 01 156.050 160.650 Duplex 02 156.100 160.700 Duplex 03 156.150 160.750 Duplex 04 156.200 160.800 Duplex 05 156.250 160.850 Duplex 06 156.300 Simplex 07 156.350 160.950 Duplex 08 156.400 Simplex 09 156.
HX270E Page 25 The following channels may be fitted to your radio. These are only licensed for use in the countries indicated. No attempt should be made to use them in any other country . Designation Tx Rx Country M 157.850 157.850 UK M2 161.425 161.425 UK 31 157.
HX270E Page 26 8. SPECIFICA TIONS 8.1 General Frequency range : 156 MHz - 163.275 MHz (Marine Band) Channel S teps: 25 kHz Frequency stability : ± 5 ppm (–30 °C to +60 °C) Emission type : 16K0G3E Antenna impedance : 50 Ohms Supply voltage : 7.2 VDC Current consumption : 200 mA (Receive) 40 mA (S tandby , Saver Off) TX: 1.
HX270E Page 27 MEMO.
HX270E Page 28 MEMO.
.
Copyright 2005 VERTEX ST ANDARD CO., L TD. All rights reserved. No portion of this manual may be reproduced without the permission of VERTEX ST ANDARD CO., L TD. Printed in Japan VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.
An important point after buying a device Vertex Standard HX270E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vertex Standard HX270E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vertex Standard HX270E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vertex Standard HX270E you will learn all the available features of the product, as well as information on its operation. The information that you get Vertex Standard HX270E will certainly help you make a decision on the purchase.
If you already are a holder of Vertex Standard HX270E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vertex Standard HX270E.
However, one of the most important roles played by the user manual is to help in solving problems with Vertex Standard HX270E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vertex Standard HX270E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
