Instruction/ maintenance manual of the product UC241N Vermont Casting
Go to page of 14
Decorative Gas Appliance For Installation In Solid Fuel Burning Fireplaces 331 1243 7/04 Rev . 1 Certified to ANSI Z21.1 1.2A Standard D E S I G N C E R T I F I E D W ARNING If the information in this manual is not followed exactly , a fire or explosion may result causing property damage, personal injury or loss of life.
2 331 1243 A TTENTION This unvented gas log heater has been certified by CSA and tested to conform to ANSI Z21.1 1.2 Gas Fired Room Heaters. Check local codes before installing this log heater . In some areas of the country , unvented gas log heaters are restricted.
3 331 1243 CARBON MONOXIDE POISONING MA Y LEAD TO DEA TH When used without fresh air , vent free gas logs may give off carbon monoxide, an odorless, poisonous gas. Some people such as pregnant women, people with heart or lung disease and persons at high altitudes are more affected by carbon monoxide than others.
4 331 1243 Provisions for Adequate Combustion and V entilation Air This heater shall not be installed in a “ CONFINED SP ACE” or unusually tight construction unless provi- sions are provided for adequate combustion and ventilation air . The NA TIONAL FUEL GAS CODE, ANSI Z223.
5 331 1243 Fireplace Spacing Requirements The illustration in Figure 2 shows spacing requirements for your room with a hood installed (not included). W ithout a hood, you must maintain a minimum of 32” between the top opening of the firebox and the bottom of a mantel which protrudes out 12”.
6 331 1243 A TTENTION: This heater is clean burning. It requires no outside venting. There is no heat loss out a vent or up a chimney . Heat is generated by realistic flames. This heater is designed for vent-free operation with flue damper closed. State and local codes in some areas prohibit the use of vent-free heaters.
7 331 1243 • If the fireplace has glass doors, remove the glass doors and frame assembly or the upper door track. • If the upper door track has been removed, follow the instructions for Figure 3. If the upper door track remains, skip Figure 3 and follow the instructions for Figure 4.
8 331 1243 Connection to Gas Supply 1. Place the burner assembly (grate and control package) in the fireplace. Center the assembly front to back and side to side. 2. Install the gas supply fitting to the gas supply pipe. Use pipe thread sealing compound, or T eflon tape, on the iron pipe threads only .
9 331 1243 Guidelines After your installer does the test burn, the log set should be operated either with the chimney open or , in the absence of a chimney , with a window open approxi- mately 1-2 inches. This operation should last for about 2-3 hours to cure the logs and dissipate any residual fumes from the new unit.
10 331 1243 Thermostatic Control The thermostat control knob can be set to any comfort level between “HI” and “LO”. The thermostat will gradually modulate the heat output and flame height from higher to lower settings in order to maintain the comfort level you select.
11 331 1243 Oxygen Depletion System For your safety , this appliance is equipped with an oxygen depletion system. This system senses the oxygen in the firebox and switches off the gas supply before the amount of oxygen falls below safe levels. (Fig. 12) Pilot ODS Sensor Flame Thermocouple Piezo Ignitor FP1505 Fig.
12 331 1243 UC/UE181, UC/UE241 Series Unvented Gas Log Heaters Ref. Description UC/UE181 UC/UE241 1a. Log Assembly - 2 Larger Bottom Logs 4312759 4312760 1b. Log Åssembly - 3 Smaller T op Logs 4312761 4312762 2. Bag of Lava Rock (2 lbs.) (2 per Heater) 20000198 20000198 3.
13 331 1243 Failure to follow all instructions in this owner ’s manual will also void this warranty . CFM Home Products will not be liable for incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you.
2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3 800-668-5323 CFM Home Products.
An important point after buying a device Vermont Casting UC241N (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vermont Casting UC241N yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vermont Casting UC241N - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vermont Casting UC241N you will learn all the available features of the product, as well as information on its operation. The information that you get Vermont Casting UC241N will certainly help you make a decision on the purchase.
If you already are a holder of Vermont Casting UC241N, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vermont Casting UC241N.
However, one of the most important roles played by the user manual is to help in solving problems with Vermont Casting UC241N. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vermont Casting UC241N along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
