Instruction/ maintenance manual of the product G400 Vermont Casting
Go to page of 20
OWNERS MANUAL GENTURY HEATING G400 VENTED GAS FIREPLAGE HEATER WARNING: lf the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal iniu.
,rrr2 S CENTURY HEATING INSTALLATION AND OPERATION INSTHUCTIONS PLEAilEREADTHTIMANUALBEF1RETNiTALLINGAND|JStNGYoUnyENTEDGAS FIREPLACE HEATER FOR YOUB SAFETY Do not store or use gasoline or otner flammable vaPorc and liquids in the vlcinitY of this or any other appliance.
1 (800) 668-5323 Monday to Friday, 9am to 5pm Eastern Standard time.
ffinsandguide|inesinthismanua|.Fai|ureto|o||owtheseinstructions exactly may resuliifri?i "i gas train Parts list F VP ffisdptlon otv' 8 S11265, 3/8" x 3" NiPPle Brass 1 ; Z)iaw l&a.
manual control wlth pressure regulator Filter Manual shut-off Flame Failure Device A= B= Q= I ,/A (r.i 6 D = Pressure Regulator E = Thermostat. F = Pilot Adjustment Outlets (2) Maximum TECHNTCAL SPEC|FICAT|ONS (EUROS|T VALVE) Inlets (2) 3/8 NPT Female 3/8 NPT Female Working Pressure 1/2 PSIG HIGH ELEVATION INSTALLANON A.
--- stove Parts llst (sEE PAGE 6) Koy# I 2 2 3 3 4 5 6 7 I I 9 10 11 12 13 14 15 16 17 18 19 otv. 1 1 1 1 2 1 3.8' 5.25' 1 3 2 2 2 1 1 1 1 1 1 1 1 1 Part llumbcr Dorcdptlon S41217 Stove Back.
ANY SAFETY SCREEN OR GUARD REMOVED FOR SERVICING AN APPLIANCE MUST BE REPLACED PRIOR TO OPERATING THE APPLIANCE. ''WARNING'' DO NOT OPERATE THE APPLIANCE WITH THE GLASS FRONT REMOVED, CRACKED OR BROKEN. REPLACEMENT OFTHE GLASS SHOUT D BE DONE BY A LICENSED OR QUALIFIED SERVICE PERSON.
FIG. A -a fan lnstallatlon instructlons (ipttonal fan klt #S3rr92l 1. Remove fan from carton. 2. Using four screws provided attach fan.to stove as shown above' ' Be sure to install rubber gromets as shown above' 3. Speed control switch is to be inserted into pedestal, as shown, and tighten until secure.
CIOTHING OR OTHER FLAMMABLE MATER'AIS SHOULD NOT BE PLACED O'V OR NEAR THE APPLIANCE. installation instructions GAS SPECIFICATIONS Manifold Pressure Minimum Inlet Pressure' Maximum lnlet Pressure Fl'U Input Rating (Max.) BTU Input Rating (Min.
temperature range The thermostat (#1 see berow drawing) is caribrated and set at the factory' (55-110"F) gas flow Maximum flow rate can be checked by cooling the thermostat bulb below room t.
yentlng Instaltailon guldeflnes PROPER INSTALLATION OF GAS VENTING IS AN IMPORTANT SAFETY AND APPLIANCE PERFOFMANCE CONCERN. IF YOU ARE NOT QUALIFIED, DO NOT ATTEMPT INSTALLATIONS Oi NCPNIRS OF GAS APPLIANCES, PIPTNG OR VENTING. flsted vents A listed gas vent is a factory made and listed system designed, and instalted exctusively toi iemoving p.
-l I I I i venting installation guldellnes WARN'NG! Installations should only be made by qualilied persons who are famillar wlth the safety procedures required for the Installation ol the Product' who arc equipped wlth the proper iools and testing instruments, and who have athleved Proper.
venting installation guidelines WARNING! Installations should only be made by qualified persons who are familiar with the salety procedures required for the installation of the product, who are equipped with the proper tools and testing instruments, and who have achieved proper certificaiion of licensing.
flltrlN I ErrttrNvs INSTr|UGTIONS 1. Periodic visual checks of the pilot should be conducted lo ensure that the flame is present excgpt when the valve control knob is in the "OFF" position. - 2. Periodically remove the logs from the grate assembly and vacuum any loose particles from the grate and burner areas.
F('r| V('U]| BEAD BEFORE SAFETY LIGHTING b. WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERIY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. This appliance has a piezo ignition pilot. When lighting the pilot, follow these instructions exacily.
- T}Io)UBLE SHOOTTNG. G4OO With proper instailation and maintenance, your new Gas Fireplace should provide yeaq of troubl+ tree dervice. lf you do experience a problem, refer to the trouble shooting- guide shown below. This guide will assiit a qualiiied servic'e persion in the diagnosis of problems and the correctlve action to be taken.
- TFOUBLE SHOOTING - G4('('- CORBECT.IVE AGTTON 1. Clean and adjust pilot flame for maximum flame impingement on thermocouple. 1. Allow unit to cool. Then repeat lighting instructions. 2. lf 1. above does not allow for ignition, check high limit switch.
'ENTTNG TROUBLE Most venting problems are caused by incorrect vent sizing, improper installation, or inadequate air supply. A preliminary check for a field problem might include: . Using a draft meter to determine if venting system draft meets manufacturer's specifica- tions.
DECORATIUE COLI.AR INSTALLATION Supplied with your G400 gas unit is a decorative collar you may wish to use to enable you to give your unit that "woodstove" look by hiding your venting inside regular 6" stove pipe. 1. I NSTALLATION I NSTRUCTIONS Center collar on vent opening and mark holes (3 places).
CFM Corporation 269 5 Meado wv al e Boule v ard Mississau ga , Ontari o L5 N 8A3 Canada (800) 668-5323 www .cfmco rp .com.
An important point after buying a device Vermont Casting G400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vermont Casting G400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vermont Casting G400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vermont Casting G400 you will learn all the available features of the product, as well as information on its operation. The information that you get Vermont Casting G400 will certainly help you make a decision on the purchase.
If you already are a holder of Vermont Casting G400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vermont Casting G400.
However, one of the most important roles played by the user manual is to help in solving problems with Vermont Casting G400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vermont Casting G400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
