Instruction/ maintenance manual of the product 3005G Vermont Casting
Go to page of 21
Assembl y and Owner’ s Manual Read all of these instructions and keep them in a safe place for future reference. Leave these instructions with the consumer . Gas Smok er CONSUMER / USER: ASSEMBLER / INST ALLER: If you smell gas: 1. Shut off gas to the appliance.
Congratulations and thank you for your purchase of your new Great Outdoors grill. W e are pleased that you have recognized the value of the design, function, and quality of components used in this product. We believe it is among the nest on the market.
3 continued... DO NOT use this smoker in a manner other than its intended purpose. It is NOT intended for commercial use. It is NOT intended to be installed or used in or on a recreational vehicle and/or boats. The smoker is not to be used as a heater .
4 Use caution when opening the door of the smoker while in operation. Keep hands, face, and body safe from hot steam or flare-ups. Protect your nose and mouth from smoke inhalation. DO NOT wear loose clothing while operating the smoker . T ie back long hair while operating the smoker .
Assembly Step 1 - Identifying the parts Check your package contents for these parts. If you are missing any parts, or if any parts are damaged, please call our toll-free customer service line to order parts.
Assembly Step 1 - Continued Check your package contents for these parts. If you are missing any parts, or if any parts are damaged, please call our toll-free customer service line to order parts. DO NOT RETURN YOUR SMOKER T O THE RET AILER - CALL US FIRST! 1-800-668-5323 6 LP tank and avoring hardwood not included.
Hardware: T ools needed: Assembly Step 2 7 HARDW ARE BAG Phillips Head Screwdriver 1. Set the cabinet assembly top side down. 2. 3. DO NOT yet insert the two bolts in the locations indicated. These two bolts will be used in the next assembly step. For each leg, line up the holes and insert the bolts.
Hardware: T ools needed: Assembly Step 3 Locate these parts: Phillips Head Screwdriver 1. Place the Control Panel Assembly between the front legs as shown. There are slots on the control panel that fit around the legs. The mounting tabs fit to the inside of the legs and line up with the bolt holes.
Hardware: T ools needed: Assembly Step 4 Locate these parts: Phillips Head Screwdriver 1. Set the burner assembly onto the cabinet as shown. IMPOR T ANT : The burner tube must slide properly onto the valve stem as shown below . 2. Secure the burner assembly with the three bolts from the inside of the cabinet.
Hardware: T ools needed: Assembly Step 5 Locate these parts: Phillips Head Screwdriver 3/8” Wrench 1. T urn the smoker upright. 2. Set the damper plate on top of the cabinet and line it up with the corresponding “butterfly” holes. One of the tabs will seat inside one of the holes.
Hardware: T ools needed: Assembly Step 6 Phillips Head Screwdriver 7/16” Wrench 1. Line up the carry handle with the corresponding holes on the side of the cabinet as shown. The handles must be positioned upright with the bolt holes on the bottom as shown.
Assembly Step 7 12 No tools or hardware are required for this step. 1. Insert the wood box rack into the bottom of the smoker . The feet of the rack sit in the four indentions in the bottom. 2. Set the wood chip box onto the rack. Make sure it is seated properly and securely in the center of the rack.
Assembly Step 8 13 No tools or hardware are required for this step. 1. Slide the water pan into the bottom rack position as shown. 2. Insert the cooking grids into any of the remaining rack positions as desired. For best access, the grid wires should run front to back as shown.
T ools needed: Phillips Head Screwdriver Assembly Step 9 Locate these parts: 1. Slide the handle washer onto the end of the door handle, followed by the handle spring as shown. 2. Feed the door handle into the hole through the front of the door panel.
15 No tools are required for this step. 1. Insert the name plate mounts and heat indicator prong through the mounting holes in the front of the door panel.
T ools needed: Assembly Step 1 1 16 Locate these parts: HARDW ARE BAG G Pliers Zip T ie OR Using the zip tie, secure the hose to the front leg as shown. Do not pull the zip tie tight - leave it just loose enough so that the hose can be adjusted if needed.
17 1 2 3 4 5 The instructions stated on gas cylinder tanks have to be followed when filling or transporting tanks. Failure to do so could result in problems relating to overfilling, excessive venting release of gas and to regulator freezing. . The knob on the LP tank must be closed.
18 LP T ank Not Included Cylinders must be filled before initial use. All handling, transport, filling and storage of LP gas cylinders must be in accordance with Cylinders must be suitably tied down during transport. Do not place any other items on top of cylinders at any time.
11 Operating Instructions Pre-Use Procedures Your smoker has been packaged with a retail store level point-of-purchase label that hangs on the front of the door panel. This label must be removed before use. To remove the label, simply cut or tear along the indicated line and pull the top portion of the label from behind the name plate.
Adding Wood / Charcoal To add wood chips before cooking, simply fill the wood chip box with your choice of flavoring hardwood chips. The amount and type of wood you use is entirely up to you. One full box is typically enough for several hours of smoking.
21 Lighting Procedure Igniter Lighting System: Match Lighting: 1. Check all connections for leaks using the “soapy water” test as explained on page 16. 2. Open the smoker cabinet door . 3. Check for any blockage to the venturi tube or burner . Remove any foreign objects or matter .
An important point after buying a device Vermont Casting 3005G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vermont Casting 3005G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vermont Casting 3005G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vermont Casting 3005G you will learn all the available features of the product, as well as information on its operation. The information that you get Vermont Casting 3005G will certainly help you make a decision on the purchase.
If you already are a holder of Vermont Casting 3005G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vermont Casting 3005G.
However, one of the most important roles played by the user manual is to help in solving problems with Vermont Casting 3005G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vermont Casting 3005G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
