Instruction/ maintenance manual of the product Meriva (2012) Vauxhall
Go to page of 225
0 - 1 Owner’s Manual Model Year 2013 Edition: June 2012 TS 1688-A-13 KTA-2690/5-VX-en VAUXHALL Meriva Owner’s Manual Model Year 2013 Edition: June 2012 TS 1688-A-13 KTA-2690/5-VX-en.
Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 19 Seats, restraints ........................... 34 Storage ........................................ 57 Instruments and controls .
2 Introduction Introduction.
Introduction 3 Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate.
4 Introduction Danger, Warnings and Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury.
Introduction 5.
6 In brief In brief Initial drive information Vehicle unlocking Press button c to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, push the touchpad switch under the tailgate moulding. Radio remote control 3 20, Central locking system 3 21, Load compartment 3 25.
In brief 7 Seat backrests Pull lever, adjust inclination and release lever. Allow the seat to engage audibly. Seat position 3 36, Seat adjustment 3 36. Seat height Lever pumping motion up = seat higher down = seat lower Seat position 3 36, Seat adjustment 3 36.
8 In brief Head restraint adjustment Press the button, adjust height and engage. To adjust horizontally, pull the head restraint forwards. It engages in several positions. To return to its rearmost position, pull fully forwards and release. Head restraints 3 34.
In brief 9 Exterior mirrors Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 28, Electric adjustment 3 28, Folding exterior mirrors 3 29, Heated exterior mirrors 3 29. Steering wheel adjustment Unlock the lever, adjust the steering wheel, then engage the lever and ensure it is fully locked.
10 In brief Instrument panel overview.
In brief 11 1 Power windows ..................... 30 2 Exterior mirrors ..................... 28 3 Cruise control ..................... 141 4 Side air vents ...................... 124 5 Turn and lane-change signals, headlight flash, low beam and high beam .
12 In brief Exterior lighting Turn light switch Auto = Automatic light control: Exterior lighting is switched on and off automatically m = activation or deactivation of the automatic light control 8 =.
In brief 13 Turn and lane-change signals lever up = right turn signal lever down = left turn signal Turn and lane-change signals 3 113, Parking lights 3 114. Hazard warning flashers Operated with the ¨ button. Hazard warning flashers 3 112. Horn Press j .
14 In brief Washer and wiper systems Windscreen wiper 2 = fast 1 = slow P = interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Windscreen wiper 3 79, Wiper blade replacement 3 163.
In brief 15 Push lever. Washer fluid is sprayed on the rear window and the wiper wipes a few times. Rear window wiper/washer 3 80. Climate control Heated rear window, heated exterior mirrors The heating is operated by pressing the Ü button. Heated rear window 3 32.
16 In brief Transmission Manual transmission Reverse: with the vehicle stationary, wait 3 seconds after depressing clutch pedal then press the release button on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection.
In brief 17 Starting the engine ■ Turn key to position 1 ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake ■ automatic transmission in P or N ■.
18 In brief Activate the anti-theft alarm system 3 27. ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. ■ Close the windows. ■ The engine cooling fans may run after the engine has been switched off 3 157.
Keys, doors and windows 19 Keys, doors and windows Keys, locks ................................... 19 Doors ........................................... 25 Vehicle security ............................ 26 Exterior mirrors ............................ 28 Interior mirrors .
20 Keys, doors and windows Radio remote control Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system ■ Power windows The radio remote control has an approximate range of up to 5 metres. It can be restricted by external influences.
Keys, doors and windows 21 Extend the key and open the unit. Replace the battery (battery type CR 2032), paying attention to the installation position. Close the unit and synchronise. Key with fixed key section Have the battery replaced by a workshop.
22 Keys, doors and windows The setting can be changed in the menu Settings in the Info-Display. Vehicle personalisation 3 105. The setting can be saved for the key being used. Memorised settings 3 21. Locking Close doors, load compartment and fuel filler flap.
Keys, doors and windows 23 Fault in radio remote control system Unlocking Manually unlock the driver's door by turning the key in the lock. Switch on the ignition and press the central locking button to unlock all doors, load compartment and fuel filler flap.
24 Keys, doors and windows Automatic locking Automatic locking after driving off The vehicle is locked automatically when exceeding a speed of 2 mph. Opening from outside is not possible. Additionally, opening of the rear doors from inside is not possible when the vehicle speed is above 2 mph.
Keys, doors and windows 25 9 Warning Use the child locks whenever children are occupying the rear seats. Using a key or suitable screwdriver, turn the child lock in the rear door to the horizontal position. The green LED will go out. The door cannot be opened from the inside.
26 Keys, doors and windows Closing Use one of the interior handles. Do not push the touchpad switch under the moulding whilst closing as this will unlock the tailgate again. Central locking system 3 21. General hints for operating tailgate 9 Warning Do not drive with the tailgate open or ajar, e.
Keys, doors and windows 27 Activating Press e on the radio remote control twice within 10 seconds. Anti-theft alarm system The anti-theft alarm system is operated in conjunction with the central locking system. It monitors: ■ Doors, tailgate, bonnet ■ Ignition Unlocking the vehicle deactivates the anti-theft alarm system.
28 Keys, doors and windows ignition on then off, then disconnect the vehicle's battery within 15 seconds. Immobiliser The system is part of the ignition switch and checks whether the vehicle is allowed to be started with the key being used. The immobiliser is activated automatically after the key has been removed from the ignition switch.
Keys, doors and windows 29 In position 0 no mirror is selected. Folding For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing.
30 Keys, doors and windows Automatic anti-dazzle Dazzle from following vehicles at night is automatically reduced. Windows Windscreen Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.
Keys, doors and windows 31 Power windows can be operated: ■ with ignition on ■ within 10 minutes of switching ignition off ■ within 5 minutes of opening or closing a door After switching off the ignition, window operation is disabled as soon as the vehicle is locked with the radio remote control.
32 Keys, doors and windows Press and hold c button to open windows. Press and hold e button to close windows. Release button to stop window movement. Overload If the windows are repeatedly operated within short intervals, the window operation is disabled for some time.
Keys, doors and windows 33 If the sun visors have integral mirrors, the mirror covers should be closed when driving. A ticket holder is located on the back of the sun visor. Roof Moonroof Do not affix any stickers to the roof. Do not cover the vehicle using a tarpaulin.
34 Seats, restraints Seats, restraints Head restraints ............................ 34 Front seats ................................... 36 Rear seats ................................... 41 Seat belts ..................................... 43 Airbag system .
Seats, restraints 35 Horizontal adjustment To adjust horizontally, pull the head restraint forwards. It engages in several positions. To return to its rearmost position, pull fully forwards and release.
36 Seats, restraints Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. ■ Sit with buttocks as far back against the backrest as possible. Adjust the distance between the seat and the pedals so that legs are slightly angled when pressing the pedals.
Seats, restraints 37 Seat positioning Pull handle, slide seat, release handle. Seat backrests Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly.
38 Seats, restraints Seat inclination Lever pumping motion up = front end higher down = front end lower Lumbar support Adjust lumbar support using the four- way switch to suit personal requirements. Moving support up and down: push switch up or down. Increasing and decreasing support: push switch forwards or backwards.
Seats, restraints 39 Armrest Detachable armrest The armrest contains a storage compartment. Storage compartment 3 59. Installing armrest Press the rear button and insert the rear guide pins into the upper guide rails. Release the button. Lower the armrest at the front.
40 Seats, restraints Moving armrest Pull the front handle slightly and move the armrest to the desired position. Release the handle. Move the armrest until it engages audibly. If a cupholder is installed in the lower guide rail, make sure that the frame of the cupholder is in the initial position.
Seats, restraints 41 Rear seats Seat adjustment 9 Warning Only drive with the outer seats engaged in the guide rails. 9 Warning Never adjust seats while driving as they could move uncontrollably. The rear outboard seats can be individually moved forward or backward.
42 Seats, restraints Pull handle and slide the seat transversely backward into position 1 . The seat is automatically guided inward. Release handle and allow seat to engage in position. Moving seats to position 2 Pull handle and slide the seat transversely forwards into position 2 .
Seats, restraints 43 Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position. Therefore the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip.
44 Seats, restraints Three-point seat belt Fastening seat belt Withdraw the belt from the retractor, guide it untwisted across the body and insert the latch plate into the buckle. Tighten the lap belt regularly whilst driving by pulling the shoulder belt.
Seats, restraints 45 Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving. Removing seat belt To release belt, press red button on belt buckle. Seat belts on the rear seats The centre rear seat is equipped with a particular three-point seat belt.
46 Seats, restraints Push the top latch plate into the retainer. Fold over locked together latch plates against the seat belt. Insert in the seat belt holder in the roof with the lower latch plate pointing forward.
Seats, restraints 47 Each airbag is triggered only once. Have deployed airbags replaced by a workshop. Furthermore, it might be necessary to have the steering wheel, the instrument panel, parts of the panelling, the door seals, handles and the seats replaced.
48 Seats, restraints Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The side airbag system consists of an airbag in each front seat backrest. This can be identified by the word AIRBAG . The side airbag system is triggered in the event of a side impact of a certain severity.
Seats, restraints 49 9 Warning Keep the area in which the airbag inflates clear of obstructions. The hooks in the roof frame are only suitable for hanging up light articles of clothing, without coat hangers.
50 Seats, restraints If the control indicator V illuminates for approx. 60 seconds after the ignition is switched on, the front passenger airbag system will inflate in the event of a collision. If both control indicators are illuminated at the same time, there is a system failure.
Seats, restraints 51 Three-point seat belt Top-Tether When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system. Always comply with local or national regulations.
52 Seats, restraints Notice Do not stick anything on the child restraint systems and do not cover them with any other materials. A child restraint system which has been subjected to stress in an accident must be replaced.
Seats, restraints 53 Child restraint installation locations Permissible options for fitting a child restraint system Weight and age class On front passenger seat On rear outboard seats On rear centre seat activated airbag deactivated airbag Group 0: up to 10 kg or approx.
54 Seats, restraints 1 = Only if front passenger seat airbag system is deactivated. If the child restraint system is being secured using a three- point seat belt, move seat height adjustment to uppermost position and ensure that vehicle seat belt runs forwards from the upper anchorage point.
Seats, restraints 55 IL = Suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories. The ISOFIX restraint system must be approved for the specific vehicle type.
56 Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. ISOFIX mounting brackets are indicated by a label on the backrest.
Storage 57 Storage Storage compartments ................ 57 Load compartment ....................... 69 Roof rack system ......................... 75 Loading information ..................... 75 Storage compartments Glovebox The glovebox features a pen holder and a coin holder.
58 Storage Fold the frame out of initial position before using. Notice If the cupholder is installed in the lower guide rail and the detachable armrest in the upper guide rail, make sure that the frame is folded back into the initial position before moving one of the parts.
Storage 59 Front storage A storage compartment is located next to the steering wheel. Underseat storage Lift drawer at recessed edge and pull out. Maximum load: 3 kg. To close, push the drawer in and engage. Armrest storage Storage in the detachable armrest Push button and fold the armrest lid upwards.
60 Storage Rear carrier system The rear carrier system (Flex-Fix system) allows bicycles to be attached to a pull-out carrier integrated into the vehicle floor. The transportation of other objects is not permitted. The maximum load of the rear carrier system is 40 kg.
Storage 61 will not engage correctly, do not fit objects to the system and slide the system back. Seek the assistance of a workshop. Install the tail lamps First remove the rear ( 1 ), then the front ( 2 ) tail lamp from the recesses. Open out the lamp support on the back of the tail lamp completely.
62 Storage Lock the rear carrier system Swivel the right clamping lever ( 1 ) first, followed by the left clamping lever ( 2 ), until a resistance is noticeable. The rear carrier system is locked when the clamping levers are swivelled by approx. 50°.
Storage 63 Unfold pedal crank recesses Fold one or both pedal crank recesses upwards until the diagonal support engages. Remove the pedal crank mounts from the pedal crank recesses. Adapting the rear carrier system to a bicycle Press the release lever and withdraw the wheel recesses.
64 Storage Push the release lever on the strap retainer and remove the strap retainer. Prepare the bicycle for attachment Notice The maximum width for the pedal crank is 38.3 mm and the maximum depth is 14.4 mm. Rotate the left pedal (without a chain cog) vertically downwards.
Storage 65 If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1 ). Put on the bicycle. The pedal crank here must be placed in the pedal crank recess opening as shown in the illustration. Caution Make sure that the pedal does not touch the surface of the rear end carrier.
66 Storage Place the wheel recesses such that the bicycle is more or less horizontal. Here, the distance between the pedals and the tailgate should be at least 5 cm. Both bicycle tyres must be in the wheel recesses. Align the bicycle in the longitudinal direction of the vehicle: Slightly loosen the pedal mount.
Storage 67 Removing a bicycle from the rear carrier system Undo strap retainers on both bicycle tyres. Hold on to the bicycle, loosen the attachment screw for the pedal bearing mount, then lift the pedal bearing mount to remove it.
68 Storage Press release lever and slide in wheel recesses all the way as far as they will go. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down. 9 Warning Risk of pinching. Remove number plate and fold down the number plate holder.
Storage 69 Push the release lever up and hold. Lift the system slightly and push it into the bumper until it engages. Release lever must return to original position. 9 Warning If the system cannot be correctly engaged, please seek the assistance of a workshop.
70 Storage Pull the handle on the front side of the backrest and fold down the backrest onto the seat cushion. The seat is lowered automatically. The backrests can also be folded from the load compartment. Pull the handle on the back side of the backrest and fold down the backrest.
Storage 71 Removing the cover Unhook retaining straps from tailgate. Lift cover at the rear and push it upwards at the front. Remove the cover. Stowing the cover Unhook retaining straps from tailgate. Lift cover at the rear and push it upwards out of the side guides at the front.
72 Storage Double load-bay floor The double load-bay floor can be inserted in the load compartment in two positions: ■ directly above the cover for the spare wheel well or the rear floor cover, ■ in the upper openings in the load compartment. To remove, lift the load-bay floor using the recess and pull backwards.
Storage 73 Installation There are two installation openings in the roof frame: suspend rod of net at one side, push to the front and engage. Extend rod, suspend at other side, push to the front and engage. Suspend hooks of net tensioning belts in lashing eyes in the floor behind the front seats.
74 Storage Roll the upper net rod down to approximately over the middle. Place the upper net rod over the tensioning straps next to the lower net rod. The hooks on the upper net rod must point away from the lower net rod. Fasten Velcro tape tightly about the net next to the length adjusters.
Storage 75 Depending on the vehicle, a box is located under the driver's seat. Pull handle and fold down the cover. Maximum load: 1.5 kg. Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended.
76 Storage ■ Use the hook at the left sidewall of the load compartment for hanging up carrier bags. Pull out the hook. Maximum load: 3 kg. ■ Secure loose objects in the load compartment to prevent them from sliding. ■ When transporting objects in the load compartment, the backrests of the rear seats must not be angled forward.
Instruments and controls 77 Instruments and controls Controls ....................................... 77 Warning lights, gauges and indi‐ cators ........................................... 84 Information displays ..................... 95 Vehicle messages .
78 Instruments and controls Heated steering wheel Activate heating by pressing * button. Activation is indicated by the LED in the button. The recommended grip areas of the steering wheel are heated quicker and to a higher temperature than the other areas.
Instruments and controls 79 Windscreen wiper/washer Windscreen wiper 2 = fast 1 = slow P = interval wiping § = off For a single wipe when the windscreen wiper is off, press the lever down. Do not use if the windscreen is frozen. Switch off in car washes.
80 Instruments and controls Adjustable sensitivity of the rain sensor Turn the adjuster wheel to adjust the sensitivity: low sensitivity = turn adjuster wheel downwards high sensitivity = turn adjuster wheel upwards Keep the sensor free from dust, dirt and ice.
Instruments and controls 81 Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times. Do not use if the windscreen is frozen. Switch off in car washes. The rear window wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged.
82 Instruments and controls Set date and time Press the CONFIG button. The menu Settings is displayed. Select Time & Date . Selectable setting options: ■ Set time : Changes the time shown on the display. ■ Set date : Changes the date shown on the display.
Instruments and controls 83 A further 12 volt power outlet is located in the rear console. Do not exceed the maximum power consumption of 120 watts. With ignition off, the power outlets are deactivated. Additionally the power outlets are deactivated in the event of low battery voltage.
84 Instruments and controls Warning lights, gauges and indicators Instrument cluster In some versions, the needles of the instruments briefly rotate to the end position when the ignition is switched on. Speedometer Indicates vehicle speed. Odometer The bottom line displays the recorded distance in miles.
Instruments and controls 85 Fuel gauge Displays the fuel level or gas level in the tank depending on the operation mode. Control indicator i illuminates if the level in the tank is low. Refuel immediately if it flashes. During liquid gas operation, the system automatically switches over to petrol operation when gas tanks are empty 3 85.
86 Instruments and controls Caution If engine coolant temperature is too high, stop vehicle, switch off engine. Danger to engine. Check coolant level. Service display The engine oil life system lets you know when to change the engine oil and filter.
Instruments and controls 87 Depending on the equipment the position of the control indicators may vary. When the ignition is switched on, most control indicators will illuminate briefly as a functionality test.
88 Instruments and controls Control indicators in the instrument cluster.
Instruments and controls 89 Control indicators in the centre console Turn signal O illuminates or flashes green. Illuminates briefly The parking lights are switched on. Flashes A turn signal or the hazard warning flashers are activated. Rapid flashing: failure of a turn signal light or associated fuse, failure of turn signal light on trailer.
90 Instruments and controls 9 Warning Have the cause of the fault remedied immediately by a workshop. Belt pretensioners, airbag system 3 43, 3 46. Airbag deactivation V illuminates yellow. Illuminates for approx. 60 seconds after the ignition is switched on.
Instruments and controls 91 Brake and clutch system Brake and clutch fluid level & illuminates red. The brake and clutch fluid level is too low 3 160. 9 Warning Stop. Do not continue your journey. Consult a workshop. Operate pedal - illuminates or flashes yellow.
92 Instruments and controls Upshift [ illuminates green or is shown as a symbol in the Driver Information Centre with Uplevel-Display when upshifting is recommended for fuel saving reasons. Variable effort steering c illuminates yellow. Fault in variable effort steering system.
Instruments and controls 93 Continue driving until % extinguishes. If possible do not allow engine speed to drop below 2000 rpm. Illuminates The diesel particle filter is full. Start cleaning process as soon as possible. Flashes The maximum filling level of the filter is reached.
94 Instruments and controls Additionally a warning message is displayed on vehicles with Midlevel- and Uplevel-Display. Catalytic converter 3 132. Bleeding the diesel fuel system 3 163. Immobiliser d flashes yellow. Fault in the immobiliser system. The engine cannot be started.
Instruments and controls 95 9 Warning Stop your journey immediately! Follow the instructions as described in paragraph "Fault in the automatic locking system" before continuing your journey 3 24.
96 Instruments and controls Selecting menus and functions The menus and functions can be selected via the buttons on the turn signal lever. Press the MENU button to switch between the menus or to return from a submenu to the next higher menu level. Turn the adjuster wheel to highlight a menu option or to set a numeric value.
Instruments and controls 97 ◆ Unit1 : Great Britain ◆ Unit2 : United States ◆ Unit3 : Europe ■ Tire Pressure System : 3 180 ■ Remaining Oil Life : 3 86 ■ Speed Warning : If exceeding the p.
98 Instruments and controls Graphic-Info-Display indicates: ■ time 3 81 ■ outside temperature 3 81 ■ date 3 81 ■ Infotainment system, see description for Infotainment system in the Infotainmen.
Instruments and controls 99 Selecting with the Infotainment system Select a function via the Infotainment system buttons. The menu of the selected function is displayed.
100 Instruments and controls Vehicle messages on the Midlevel-Display The vehicle messages are displayed as code numbers. No. Vehicle message 2 No radio remote control detected, depress clutch pedal for a restart 3 Engine coolant level low 4 Air conditioning off 5 Steering wheel is locked No.
Instruments and controls 101 No. Vehicle message 55 Diesel particle filter is full 3 131 56 Tyre pressure imbalance on front axle 57 Tyre pressure imbalance on rear axle 58 Tyres without TPMS sensors .
102 Instruments and controls ■ Brakes ■ Drive systems ■ Ride control systems ■ Cruise control ■ Object detection systems ■ Lighting, bulb replacement ■ Wiper/washer system ■ Doors, win.
Instruments and controls 103 The warning message or warning code will disappear after the engine has been started two times running without voltage drop. If the battery cannot be recharged, have the cause of the fault remedied by a workshop. Trip computer The menus and functions can be selected via the buttons on the turn signal lever.
104 Instruments and controls The information of the two trip computers can be reset separately, making it possible to display different trip distances. To reset, press the SET/CLR button for a few seconds. On vehicles with reset knob, hold the reset knob depressed for a few seconds with the ignition on.
Instruments and controls 105 Vehicle personalisation The vehicle's behaviour can be personalised by changing the settings in the Info-Display. Some of the personal settings for different drivers can be memorised individually for each vehicle key.
106 Instruments and controls Time Date See Clock 3 81. Radio settings See description for Infotainment system in the Infotainment system manual. Phone settings See description for Infotainment system in the Infotainment system manual. Vehicle settings ■ Climate and air quality Auto fan speed : Modifies the fan regulation.
Instruments and controls 107 Personal settings in the Colour-Info-Display Press the CONFIG button. The menu Settings is displayed. The following settings can be selected by turning and pressing the mu.
108 Instruments and controls ■ Comfort settings Chime volume : Change the volume of warning chimes. Rear auto wipe in reverse : Activate or deactivate automatic switching on of the rear window wiper when reverse gear is engaged. ■ Park assist / Collision detection Park assist : Activate or deactivate the ultrasonic parking assist.
Lighting 109 Lighting Exterior lighting .......................... 109 Interior lighting ........................... 114 Lighting features ........................ 116 Exterior lighting Light switch Turn light switch: AUTO = automatic light control: Exterior lighting is switched on and off automatically depending on external lighting conditions.
110 Lighting Automatic light control When the automatic light control function is switched on and the engine is running, the system switches between daytime running light and low beam depending on the lighting conditions. Daytime running light Daytime running light increases visibility of the vehicle during daylight.
Lighting 111 0 = front seats occupied 1 = all seats occupied 2 = all seats occupied and load compartment laden 3 = driver's seat occupied and load compartment laden. Headlights when driving abroad The asymmetrical headlight beam extends visibility at the edge of the road at the passenger side.
112 Lighting 3. Switch on ignition. 4. After approx. 5 seconds the control indicator f starts flashing and an acoustic signal sounds. Control indicator f 3 94. Every time the ignition is switched on, f flashes as a reminder for approx. 4 seconds. For deactivation operate the same procedure as described above.
Lighting 113 Turn and lane-change signals lever up = right turn signal lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated.
114 Lighting Parking lights When the vehicle is parked, the parking lights on one side can be activated: 1. Switch off ignition. 2. Move turn signal lever all the way up (right parking lights) or down (left parking lights). Confirmed by a signal and the corresponding turn signal control indicator.
Lighting 115 On vehicles with light sensor the brightness can only be adjusted when the exterior lights are on and the light sensor detects night conditions. Interior lights During entry and exit of the vehicle, the front and rear courtesy lights automatically switch on and then off after a delay.
116 Lighting Lighting features Centre console lighting Spotlight incorporated in the interior lighting comes on when the low beam is switched on. Entry lighting Welcome lighting The exterior lights, instrument panel light and interior lights are switched on for a short time by pressing the unlocking button c on the radio remote control twice.
Lighting 117 Activation, deactivation and duration of this function can be changed in the menu Settings in the Info-Display. Vehicle personalisation 3 105.
118 Climate control Climate control Climate control systems ............. 118 Air vents ..................................... 124 Maintenance .........
Climate control 119 Notice If the settings for demisting and defrosting are selected, an Autostop will be inhibited. If the settings for demisting and defrosting are selected while the engine is in an Autostop, the engine will restart automatically. Stop-start system 3 129.
120 Climate control ■ Set fan speed to highest level. ■ Open all vents. Demisting and defrosting the windows V ■ Press button V : fan automatically switches to higher speed, the air distribution is directed towards the windscreen. ■ Switch cooling n on.
Climate control 121 The preselected temperature is automatically regulated. In the automatic mode the fan speed and air distribution automatically regulate the air flow. The system can be manually adapted via the use of air distribution and air flow controls.
122 Climate control If the minimum temperature is set, the climate control system runs at maximum cooling, if cooling n is switched on. If the maximum temperature is set, the climate control system runs at maximum heating. Notice If the temperature is set to Lo or Hi , an Autostop will be inhibited.
Climate control 123 s = to windscreen and front door windows M = to head area via adjustable air vents K = to foot well All combinations are possible. Return to automatic air distribution: Deactivate corresponding setting or press button AUTO . Cooling Activate or deactivate with the n button.
124 Climate control Auxiliary heater Air heater Quickheat is an electric auxiliary air heater which automatically warms up the passenger compartment more quickly. Air vents Adjustable air vents To open the vent, turn the adjuster wheel to the right. Adjust the air amount at the vent outlet by turning the adjuster wheel.
Climate control 125 Maintenance Air intake The air intake in front of the windscreen in the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow. Pollen filter Cabin air filtration A particle filter cleans the cabin air from dust, soot, pollen and spores.
126 Driving and operating Driving and operating Driving hints ............................... 126 Starting and operating ............... 127 Engine exhaust .......................... 131 Automatic transmission .............. 133 Manual transmission ..
Driving and operating 127 Starting and operating New vehicle running-in Do not brake unnecessarily hard for the first few journeys. During the first drive, smoke may occur because of wax and oil evaporating off the exhaust system. Park the vehicle in the open for a while after the first drive and avoid inhaling the fumes.
128 Driving and operating Diesel engine: turn the key to position 2 for preheating until control indicator ! extinguishes. Turn the key briefly to position 3 and release: an automatic procedure operates the starter with a short delay as long as the engine is running, see Automatic Starter Control.
Driving and operating 129 Stop-start system The stop-start system helps to save fuel and to reduce the exhaust emissions. When conditions allow, it switches off the engine as soon as the vehicle is at a low speed or at a standstill, e.g. at a traffic light or in a traffic jam.
130 Driving and operating ■ The stop-start system is not manually deactivated ■ the bonnet is fully closed ■ the driver's door is closed or the driver's seat belt is fastened ■ the b.
Driving and operating 131 ■ the driver's seat belt is unfastened and the driver's door is opened ■ the engine temperature is too low ■ the battery is discharged ■ the brake vacuum is.
132 Driving and operating take up to 25 minutes. Typically it needs between 7 and 12 minutes. Autostop is not available and fuel consumption may be higher during this period. The emission of smells and smoke during this process is normal. Under certain driving conditions, e.
Driving and operating 133 rectified by a workshop as soon as possible. In an emergency, driving can be continued for a short period, keeping vehicle speed and engine speed low. Automatic transmission The automatic transmission permits automatic gearshifting (automatic mode) or manual gearshifting (manual mode).
134 Driving and operating Without brake pedal applied, the control indicator j illuminates. If the selector lever is not in P when the ignition is switched off, the control indicator j and P flash. To engage P or R , press the release button. The engine can only be started with the lever in position P or N .
Driving and operating 135 In manual mode no automatic shifting to a higher gear takes place at high engine revolutions. Electronic driving programmes ■ Following a cold start, the operating temperature programme increases engine speed to quickly bring the catalytic converter to the required temperature.
136 Driving and operating 5. Insert a screwdriver into the opening as far as it will go and move the selector lever out of P or N . If P or N is engaged again, the selector lever will be locked in position again. Have the cause of the power supply interruption remedied by a workshop.
Driving and operating 137 Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when the brake pedal is depressed firmly.
138 Driving and operating Parking brake Electrical parking brake Applying when vehicle is stationary Pull switch m for approx. half a second, the electrical parking brake operates automatically with an adequate force. For maximum force, e.g. parking with trailer or on inclines, pull switch m twice.
Driving and operating 139 Control indicator m flashes: electrical parking brake is not fully applied or released. When continuously flashing, release electrical parking brake and retry applying. Brake assist If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking).
140 Driving and operating 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Adapt speed to the road conditions. Control indicator b 3 92. Deactivation TC can be switched off when spinning of drive wheels is required: press button b briefly.
Driving and operating 141 ESC is reactivated by pressing the b button again. If the TC system was previously disabled, both TC and ESC are reactivated. ESC is also reactivated the next time the ignition is switched on. Cruise control The cruise control can store and maintain speeds of approx.
142 Driving and operating Increase speed With cruise control active, hold thumb wheel turned to RES/+ or briefly turn to RES/+ repeatedly: speed increases continuously or in small increments. Alternatively accelerate to the desired speed and store by turning to RES/+ .
Driving and operating 143 parking assist the system consists of four additional ultrasonic parking sensors in the front bumper. Control indicator r 3 92. Activation When reverse gear is engaged, the system is activated automatically. The front parking assist can also be activated at a low speed by pressing the r button.
144 Driving and operating Caution Performance of the sensor can be reduced when sensors are covered, e.g. by ice or snow. Performance of the parking assist systems can be reduced due to heavy loading. Special conditions apply if there are taller vehicles involved (e.
Driving and operating 145 Caution Use of fuel that does not comply to EN 228 or E DIN 51626-1 or equivalent can lead to deposits or engine damage and loss of warranty. Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage.
146 Driving and operating Pressing the LPG button switches between petrol and liquid gas operation as soon as the required parameters (coolant temperature, gas temperature and minimum engine speed) have been reached.
Driving and operating 147 Turn the thumb wheel clockwise. If no further gas odour is perceptible when the manual shut-off valve is closed, the vehicle can be used in petrol mode. If the gas odour persists, do not start the engine. Have the cause of the fault remedied by a workshop.
148 Driving and operating The fuel filler flap can only be opened if the vehicle is unlocked. Pull flap at the recess and open. To open, turn the cap slowly to the left. The fuel filler cap can be retained in the bracket on the fuel filler flap. For refuelling, fully insert the pump nozzle and switch it on.
Driving and operating 149 Fit the required adapter. ACME Adapter: Screw the nut of the filling nozzle onto the adapter. Press locking lever on filler nozzle down. DISH (Italy) filler neck: Place the filler nozzle into the adapter. Press locking lever on filler nozzle down.
150 Driving and operating ACME adapter: Belgium, Germany, Ireland, Luxembourg, Switzerland Bayonet adapter: Netherlands, Norway, Spain, United Kingdom EURO adapter: Spain DISH (Italy) adapter: Bosnia-.
Driving and operating 151 General information The official fuel consumption and specific CO 2 emission figures quoted relate to the EU base model with standard equipment. Fuel consumption data and CO 2 emission data are determined according to regulation R (EC) No.
152 Driving and operating Trailer towing Trailer loads 9 Warning Vehicles with engine A13DTE: Use of towing equipment is permissible for attaching compatible bicycle carriers only. Do not use towing equipment for trailer towing. The permissible trailer loads are vehicle and engine-dependent maximum values which must not be exceeded.
Driving and operating 153 Stowage of the detachable coupling ball bar The bag with the coupling ball bar is stowed in the rear stowage compartment on the floor. Stick the strap through the lashing eye and tighten the strap to secure the bag. Fitting the detachable coupling ball bar Disengage and fold down the socket.
154 Driving and operating Pull out rotary knob and turn clockwise as far as it will go. Inserting the coupling ball bar Insert the tensioned coupling ball bar in the opening and push firmly upwards until it audibly engages. The rotary handle snaps back into its original position resting against the coupling ball bar without a gap.
Driving and operating 155 ■ The coupling ball bar must be firmly engaged in the opening. ■ The coupling ball bar must be locked and the key removed. 9 Warning Towing a trailer is permitted only when a coupling ball bar is fitted correctly. If the coupling ball bar does not engage correctly, seek the assistance of a workshop.
156 Vehicle care Vehicle care General Information ................... 156 Vehicle checks ........................... 157 Bulb replacement ....................... 164 Electrical system ........................ 173 Vehicle tools ........................
Vehicle care 157 ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery.
158 Vehicle care 9 Danger The ignition system use extremely high voltage. Do not touch. Bonnet Opening Pull the release lever and return it to its original position. Press the safety catch and open the bonnet. Secure the bonnet support. If the bonnet is opened during an Autostop, the engine will be restarted automatically for safety reasons.
Vehicle care 159 Different dipsticks are used depending on engine variant. When the engine oil level has dropped to the MIN mark, top up engine oil. We recommend the use of the same grade of engine oil that was used at last change. The engine oil level must not exceed the MAX mark on the dipstick.
160 Vehicle care If the cooling system is cold, the coolant level should be above the filling line mark. Top up if the level is low. 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. To top up use a 1:1 mixture of approved coolant concentrate mixed with clean tap water.
Vehicle care 161 The brake fluid level must be between the MIN and the MAX marks. When topping up, ensure maximum cleanliness as contamination of the brake fluid can lead to brake system malfunctions. Have the cause of the loss of brake fluid remedied by a workshop.
162 Vehicle care An AGM battery can be identified by the label on the battery. We recommend the use of an original Vauxhall battery. Notice Using an AGM battery different from the original Vauxhall battery might result in a lower performance of the stop-start system.
Vehicle care 163 ■ See the Owner's Manual for further information. ■ Explosive gas may be present in the vicinity of the battery. Diesel fuel system bleeding If the tank has been run dry, the diesel fuel system must be bled. Switch on the ignition three times for 15 seconds at a time.
164 Vehicle care Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Replace headlight bulbs from within the engine compartment.
Vehicle care 165 3. Detach the bulb from the bulb holder and replace the bulb. 4. Insert the bulb holder into the reflector. 5. Fit the cap and rotate clockwise. High beam 1. Rotate the cap 2 anticlockwise and remove it. 2. Detach the plug from the bulb.
166 Vehicle care 2. Detach bulb from the bulb holder and replace it. 3. Insert the bulb holder into the reflector and rotate clockwise. Front turn signal 1. Rotate the bulb holder anticlockwise and remove it. 2. Rotate bulb anticlockwise and remove from bulb holder.
Vehicle care 167 Low beam/High beam 1. Rotate the cap 1 anticlockwise and remove it. 2. Push the bulb holder downwards and withdraw the bulb holder from the reflector. 3. Detach the bulb from the bulb holder and replace the bulb. 4. Insert the bulb holder into the reflector.
168 Vehicle care 2. Press catch and withdraw the bulb holder from the reflector. 3. Remove and replace the bulb. 4. Press catch and insert the bulb holder into the reflector. 5. Fit the cap and rotate clockwise. Cornering light 1. Rotate protective cover 2 anticlockwise and remove.
Vehicle care 169 1. Turn the bulb holder anticlockwise and remove it from the reflector. 2. Disengage the bulb holder from the plug connector by pressing the retaining lug. 3. Remove and replace the bulb holder with bulb. 4. Attach the plug connector.
170 Vehicle care 3. Carefully withdraw the light assembly from retaining pins and remove. Make sure that the cable duct remains in position. 4. Detach the wiring plug from the bulb carrier. 5. Unlatch the four retaining lugs and remove the bulb carrier.
Vehicle care 171 2. Press the retaining lug and remove the bulb carrier downwards. 3. To replace the reverse light bulb ( 1 ), remove and replace the bulb To replace the tail light bulb ( 2 ), push the bulb slightly into the socket, rotate anticlockwise, remove and replace the bulb.
172 Vehicle care Interior lights Courtesy light, reading lights Have bulbs replaced by a workshop. Load compartment light Have bulbs replaced by a workshop. Puddle lights 1. Disengage the housing at the bottom and remove it. 2. Press the retaining lug and withdraw the connector.
Vehicle care 173 Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. There are three fuse boxes in the vehicle: ■ in the front left of the engine compartm.
174 Vehicle care Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. Engine compartment fuse box The fuse box is in the front left of the engine compartment. Disengage the cover, lift it upwards and remove. After having changed defective fuses close the fuse box cover and press until it engages.
Vehicle care 175 No. Circuit 1 Starter 2 – 3 Fuel filter, cooling 4 Horn 5 Terminal 30 6 Engine control module, trans‐ mission control unit 7 Fog light 8 Engine cooling 9 Engine cooling 10 Vacuum pump 11 Ignition, preheating 12 Headlamp levelling 13 Air conditioning system, terminal 15 14 Transmission control unit 15 High beam right No.
176 Vehicle care No. Circuit 22 Electrical parking brake 23 Tyre repair kit 24 Fuel pump 25 ABS 26 Heated rear window 27 ABS 28 Interior fan 29 Cigarette lighter 30 Air conditioning system 31 Front po.
Vehicle care 177 No. Circuit 1 Radio 2 Display, instrument, telephone 3 Radio 4 Ignition switch, immobiliser 5 Windscreen washer, rear screen washer 6 Central locking system, tailgate 7 Central lockin.
178 Vehicle care No. Circuit 1 Adaptive forward lighting 2 – 3 – 4 – 5 – 6 Rear power window, right 7 Adaptive forward lighting 8 Trailer module, Trailer socket 9 Seat, lumbar support, left 10.
Vehicle care 179 Vehicles with tyre repair kit To open the compartment, disengage the cover and open it. The vehicle tools are in the right-hand compartment in the load compartment, together with the tyre repair kit. Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible.
180 Vehicle care Tyre designations E.g. 195/65 R 15 91 H 195 = Tyre width, mm 65 = Cross-section ratio (tyre height to tyre width), % R = Belt type: Radial RF = Type: RunFlat 15 = Wheel diameter, inches 91 = Load index e.
Vehicle care 181 System initialisation After tyre pressure correction or wheel change, the system must be initiated: 1. Apply electrical parking brake. 2. Press the MENU button to select the Vehicle Information Menu . 3. Turn the adjuster wheel to select Tire Pressure System .
182 Vehicle care Changing tyre and wheel size If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogramme the speedometer as well as the nominal tyre pressure and make other vehicle modifications. After converting to a different tyre size, have the label with tyre pressures replaced.
Vehicle care 183 Tyre damage exceeding 4 mm or that is at the tyre's sidewall near the rim cannot be repaired with the tyre repair kit. 9 Warning Do not drive faster than 50 mph. Do not use for a lengthy period. Steering and handling may be affected.
184 Vehicle care 3. Position the sealant bottle on the bracket. Make sure that the bottle does not fall. 4. Unscrew valve cap from defective tyre. 5. Screw tyre inflation hose to valve. 6. Screw air hose onto compressor connection. 7. Switch on ignition.
Vehicle care 185 12. Push catch on bracket to remove sealant bottle from bracket. Screw the tyre inflation hose to the free connection of the sealant bottle. This prevents sealant from escaping. Stow tyre repair kit in load compartment. 13. Remove any excess sealant using a cloth.
186 Vehicle care ■ If the ground on which the vehicle is standing is soft, a solid board (max. 1 cm thick) should be placed under the jack. ■ No people or animals may be in the vehicle when it is jacked-up. ■ Never crawl under a jacked-up vehicle.
Vehicle care 187 3. Ensure the jack is positioned correctly with the vehicle jacking points. Lifting the vehicle onto a lifting platform: Position the rear arm of the lifting platform at the underbody. Position the front arm of the lifting platform at the underbody.
188 Vehicle care Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping. Attach wheel wrench and with the jack correctly aligned rotate wheel wrench until wheel is clear of the ground.
Vehicle care 189 The spare wheel is located in the load compartment beneath the floor covering. It is secured with a wing nut. The spare wheel well is not designed for all permissible tyre sizes.
190 Vehicle care ■ Take the extension bar from the tool box and screw it on the bolt. ■ Store the damaged wheel and secure it by turning the wing nut clockwise. The floor cover can be placed on the projecting wheel. Remove the extension bar before fitting the spare wheel in the well after renewing or repairing the defective wheel.
Vehicle care 191 Jump starting Do not start with quick charger. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle.
192 Vehicle care 3. Connect the black lead to the negative terminal of the booster battery. 4. Connect the other end of the black lead to a vehicle grounding point, such as the engine block or an engine mounting bolt. Connect as far away from the discharged battery as possible, however at least 60 cm.
Vehicle care 193 Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the towing eye. The towing eye must only be used for towing and not for recovering the vehicle.
194 Vehicle care Screw in the towing eye as far as it will go until it stops in a horizontal position. The lashing eye at the rear underneath the vehicle must never be used as a towing eye. Attach a tow rope – or even better a tow bar – to the towing eye.
Vehicle care 195 If using a vehicle wash, comply with the vehicle wash manufacturer's instructions. The windscreen wiper and rear window wiper must be switched off. Remove antenna and external accessories such as roof racks etc. If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out.
196 Vehicle care Clean rims with a pH-neutral wheel cleaner. Rims are painted and can be treated with the same agents as the body. Paintwork damage Rectify minor paintwork damage with a touch-up pen before rust forms. Have more extensive damage or rust areas repaired by a workshop.
Vehicle care 197 Caution Close Velcro fasteners as open Velcro fasteners on clothing could damage seat upholstery. The same applies to clothing with sharp-edged objects, like zips or belts or studded jeans. Plastic and rubber parts Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body.
198 Service and maintenance Service and maintenance General information ................... 198 Recommended fluids, lubricants and parts ..............
Service and maintenance 199 Make sure that the Service and Warranty Booklet is completed correctly as continuous proof of service is essential if any warranty or goodwill claims are to be met, and is also a benefit when selling the vehicle.
200 Service and maintenance Select the appropriate engine oil based on its quality and on the minimum ambient temperature 3 203. Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty.
Technical data 201 Technical data Vehicle identification .................. 201 Vehicle data ............................... 203 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is stamped on the identification plate and on the floor pan, under the floor covering, visible under a cover.
202 Technical data Identification plate The identification plate is located on the rear right-hand door frame. Information on identification label: 1 = Manufacturer 2 = Type approval number 3 = Vehicl.
Technical data 203 Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries ( except Belarus, Moldova, Russia, Serbia, Turkey) Only I.
204 Technical data International service schedule Required engine oil quality All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines.
Technical data 205 All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (i.
206 Technical data Engine data Sales designation 1.4 1.4 1.4 1.4 1.3 Engine identifier code A14XER A14NEL B14NEL A14NET A13DTC Number of cylinders 4 4 4 4 4 Piston displacement [cm 3 ] 1398 1364 1364 .
Technical data 207 Sales designation 1.3 1.7 1.7 1.7 1.7 Engine identifier code A13DTE A17DT A17DTC A17DTS A17DTI Number of cylinders 4 4 4 4 4 Piston displacement [cm 3 ] 1248 1686 1686 1686 1686 Eng.
208 Technical data Engine A13DTE A17DT A17DTC A17DTS A17DTI Maximum speed 6) [mph] Manual transmission 104 – 113 122 – Automatic transmission – 107 – – 111 6) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload.
Technical data 209 Vehicle weight Kerb weight, basic model without any optional equipment Engine Manual transmission Automatic transmission without/with air conditioning [kg] A14XER 1361/1376 – A14N.
210 Technical data Kerb weight, basic model with all optional equipment Engine Manual transmission Automatic transmission without/with air conditioning [kg] A14XER –/1571 – A14NEL –/1613 – B14.
Technical data 211 Vehicle dimensions Length [mm] 4288 Width without exterior mirrors [mm] 1812 Width with two exterior mirrors [mm] 1994 Height (without antenna) [mm] 1615 Length of load compartment .
212 Technical data Capacities Engine oil Engine A14XER A14NEL B14NEL A14NET A13DTC including Filter [l] 4.0 4.0 4.0 4.0 3.5 between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 Engine A13DTE A17DT A17DTC A17DTS A17DTI including Filter [l] 3.5 5.4 5.4 5.4 5.4 between MIN and MAX [l] 1.
Technical data 213 Tyre pressures Comfort with up to 3 people ECO with up to 3 people With full load Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) A14XER 195/65 R15, 230/2.
214 Technical data Comfort with up to 3 people ECO with up to 3 people With full load Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) A14NET 205/55 R16, 230/2.
Technical data 215 Comfort with up to 3 people ECO with up to 3 people With full load Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) A17DT, A17DTC, A17DTS, A17DTI 195/65 R15 11)12) , 250/2.
216 Technical data Towing hitch installation dimensions.
Customer information 217 Customer information Vehicle data recording and pri‐ vacy ........................................... 217 Vehicle data recording and privacy Event data recorders Data storag.
218 Customer information When using the vehicle, situations may occur in which these technical data related to other information (accident report, damages on the vehicle, witness statements etc.) may be associated with a specific person - possibly, with the assistance of an expert.
Customer information 219.
220 Index A Accessories and vehicle modifications .......................... 156 Active head restraints .................. 35 Adaptive brake light .................... 137 Adaptive forward lighting .......... .................................. 94, 112, 166 Adjustable air vents .
221 Child restraints.............................. 50 Child restraint systems ................ 50 Cigarette lighter ........................... 83 Climate control ............................. 15 Climate control, service .............. 125 Climate control systems .
222 Fuse box ..................................... 174 Fuses ......................................... 173 G Gauges ......................................... 84 General information ................... 151 Glovebox .....................................
223 Odometer ..................................... 84 Oil ............................................... 158 Oil, engine .......................... 199, 203 Oil pressure .................................. 93 Outside temperature .................... 81 Overrun cut-off .
224 Towing ................................ 151, 192 Towing another vehicle ............. 193 Towing a trailer ........................... 152 Towing equipment ..................... 152 Towing hitch installation dimensions ............................
An important point after buying a device Vauxhall Meriva (2012) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vauxhall Meriva (2012) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vauxhall Meriva (2012) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vauxhall Meriva (2012) you will learn all the available features of the product, as well as information on its operation. The information that you get Vauxhall Meriva (2012) will certainly help you make a decision on the purchase.
If you already are a holder of Vauxhall Meriva (2012), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vauxhall Meriva (2012).
However, one of the most important roles played by the user manual is to help in solving problems with Vauxhall Meriva (2012). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vauxhall Meriva (2012) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
