Instruction/ maintenance manual of the product Combo (2011) Vauxhall
Go to page of 147
0 - 1 Owner’s Manual Model Year 20 12 Edition: November 2011 TS 1714-B-12 VAUXHALL Combo Owner’s Manual Model Year 2012 Edition: November 2011 TS 1714-B-12.
Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 18 Seats, restraints ........................... 29 Storage ........................................ 44 Instruments and controls .
2 Introduction Introduction.
Introduction 3 Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage.
Introduction 5.
6 In brief In brief Initial drive information Vehicle unlocking Unlocking with key Turn the key in the driver's door lock to the front. Unlocking with radio remote control Press button Ä to unlock the doors and load compartment. Open the doors by pulling the handles, to open the tailgate, press the button under the handle.
In brief 7 Seat adjustment Seat positioning Pull handle, slide seat, release handle. Seat position 3 30, Seat adjustment 3 31. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. Seat backrests Turn handwheel.
8 In brief Head restraint adjustment Press release catch, adjust height, engage. Head restraints 3 29. Seat belt Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx.
In brief 9 Exterior mirrors Swivel lever in required direction. Select the relevant exterior mirror by turning the control to left _ or right 6 . Then swivel the control to adjust the mirror. In position o no mirror is selected. Convex exterior mirrors 3 25, Electric adjustment 3 25, Folding exterior mirrors 3 25, Heated exterior mirrors 3 26.
10 In brief Instrument panel overview.
In brief 11 1 Fixed air vents ....................... 77 2 Side air vents ........................ 76 3 Light switch .......................... 68 Turn and lane-change signals, headlight flash, low beam and high beam ..... 70 4 Instruments ...........
12 In brief Fog lights Press light switch > = front fog lights r = rear fog light Headlight flash, high beam and low beam headlight flash = pull lever high beam = push lever low beam = pull lever High beam 3 68, Headlight flash 3 68.
In brief 13 Hazard warning flashers Operated with the ¨ button. Hazard warning flashers 3 69. Horn Press j . Washer and wiper systems Windscreen wiper Twist lever: É = fast È = slow Ç = intermittent wiping § = off For a single wipe when the windscreen wiper is off, move the lever up.
14 In brief Windscreen and headlight washer systems Pull lever: Windscreen and headlight washer system 3 51, Washer fluid 3 102. Rear window wiper and washer systems Twist to activate the rear window wiper. The rear screen wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged.
In brief 15 Demisting and defrosting the windows Set the temperature control to V . Set fan to 4 . Set air distribution control to V . Cooling n on. Heated rear window Ü on.
16 In brief Starting off Check before starting off ■ Tyre pressure and condition 3 114, 3 138. ■ Engine oil level and fluid levels 3 100. ■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational.
In brief 17 Parking ■ Always apply the parking brake. Activate the manual parking brake without pressing the release button. Apply as firmly as possible on a downhill slope or uphill slope. Depress foot brake at the same time to reduce operating force.
18 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 18 Doors ........................................... 21 Vehicle security ............................ 24 Exterior mirrors ............................ 25 Interior mirrors .
Keys, doors and windows 19 Radio remote control Used to operate: ■ Central locking system ■ Anti-theft locking system The radio remote control has an approximate range of up to 5 metres. It can be restricted by external influences. The hazard warning flashers confirm operation.
20 Keys, doors and windows replace the battery (type CR 2032), paying attention to the installation position. Refit the battery holder in the key and secure the screw. Central locking system Unlocks and locks doors and load compartment. A pull on an interior door handle unlocks the entire vehicle and opens the door.
Keys, doors and windows 21 Unlocking the load compartment from inside the vehicle Press button Å : The load compartment (rear doors / tailgate and sliding side doors) are unlocked. When the load compartment is locked the LED in the button is illuminated.
22 Keys, doors and windows Rear doors To open the left hand rear door pull the outside handle. The door is opened from inside the vehicle by pressing down the interior handle. The right hand rear door is released using the lever. 9 Warning The rear lights may be obscured if the rear doors are open and the vehicle is parked on the roadside.
Keys, doors and windows 23 9 Warning Ensure extended opening doors are secured when fully opened. Opened doors may slam closed due to the force of the wind! Always close the right hand door before the left hand door. Load compartment Tailgate Opening Press the button underneath the moulding.
24 Keys, doors and windows Vehicle security Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. The system deadlocks all the doors. All doors must be closed otherwise the system cannot be activated.
Keys, doors and windows 25 Exterior mirrors Convex shape The convex exterior mirror contains an aspherical area and reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the ability to estimate distances. Manual adjustment Adjust mirrors by swivelling lever in required direction.
26 Keys, doors and windows Heated Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Interior mirrors Manual anti-dazzle Adjust the lever on the underside to reduce dazzle. Windows Manual windows The door windows can be opened or closed with the window winders.
Keys, doors and windows 27 Operate the switch for the respective window by pushing to open or pulling to close. Pushing or pulling briefly: window moves up or down in stages if the switch is held. Pushing or pulling firmly and then releasing: window moves up or down fully with safety function enabled.
28 Keys, doors and windows Rear windows Opening rear windows To open, move lever outwards until the window is fully open. To close, pull lever then push until window is fully closed. Heated rear window Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time.
Seats, restraints 29 Seats, restraints Head restraints ............................ 29 Front seats ................................... 30 Seat belts ..................................... 32 Airbag system .............................. 35 Child restraints .
30 Seats, restraints Head restraints on rear seats Height adjustment Pull the head restraint upwards or press the catch to release and push the head restraint downwards. Removal Press both catches, pull the head restraint upwards and remove. Front seats Seat position 9 Warning Only drive with the seat correctly adjusted.
Seats, restraints 31 Seat adjustment 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat positioning Pull handle, slide seat, release handle.
32 Seats, restraints Armrest Raise or lower the armrest as required. Heating Activate heating by pressing ß button for the seat with the ignition on. LED in button ß on: relevant front seat heating on. Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position.
Seats, restraints 33 Seat belts are designed to be used by only one person at a time. They are not suitable for people smaller than 150 cm. Child restraint system 3 38. Periodically check all parts of the belt system for damage, pollution and proper functionality.
34 Seats, restraints Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing.
Seats, restraints 35 Removing To release belt, press red button on belt buckle. Seat belts on the rear seats The seat belt for the rear centre seat can only be withdrawn from the retractor if the backrest is in the rear position.
36 Seats, restraints Notice The airbag systems and belt pretensioner control electronics are located in the centre console area. Do not put any magnetic objects in this area. Do not fix any objects onto the airbag covers and do not cover them with other materials.
Seats, restraints 37 Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The side airbag system consists of an airbag in each front seat backrest. This can be identified by the word AIRBAG . The side airbag system is triggered in the event of a side impact of a certain severity.
38 Seats, restraints Front passenger seat airbags are deactivated and will not inflate in the event of a collision. Control indicator * illuminates continuously in the instrument cluster. A child restraint system can be installed in accordance with the chart Child restraint installation locations 3 40.
Seats, restraints 39 deactivated; if not, the triggering of the airbags poses a risk of fatal injury to the child. This is especially the case if rear- facing child restraint systems are used on the front passenger seat. Selecting the right system The rear seats are the most convenient location to fasten a child restraint system.
40 Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system Weight and age class Front passenger seat Second row Third row activated airbag deactivated airbag outboard seat centre seat Group 0: up to 10 kg or approx.
Seats, restraints 41 Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture On front passenger seat On outboard seats in the second row On centre seat in the .
42 Seats, restraints ISOFIX size class and seat device A – ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. B – ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
Seats, restraints 43 ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. ISOFIX mounting brackets are indicated by a label on the backrest.
44 Storage Storage Storage compartments ................ 44 Load compartment ....................... 46 Roof rack system ......................... 48 Loading information ..................... 49 Storage compartments Instrument panel storage Storage compartments are located in the instrument panel.
Storage 45 Glovebox The glovebox should be closed whilst driving. Cupholders Cupholders are located in the centre console. The cupholders can also be used to hold the portable ashtray unit 3 55. Overhead console Store only lightweight items such as paperwork or maps in the overhead console.
46 Storage Load compartment Folding down rear seat backrests The rear seat backrest is divided into two parts. Both parts can be folded down. Remove the load compartment cover if necessary. Press and hold the catch, then push the head restraints down.
Storage 47 Closing Pull the cover towards the rear using the handle and engage it in the retainers at the sides. Opening Remove load compartment cover from the retainers at the sides. Hold the cover and guide it until it is fully rolled up. Removing Open the load compartment cover.
48 Storage Lashing eyes The lashing eyes are designed to secure items against slippage, e.g. using lashing straps or luggage net. Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended.
Storage 49 Loading information ■ Heavy objects in the load compartment should be evenly distributed and placed as far forward as possible. If objects can be stacked, the heavier objects should be placed at the bottom. ■ Secure objects with lashing straps attached to lashing eyes 3 48.
50 Instruments and controls Instruments and controls Controls ....................................... 50 Warning lights, gauges and indicators ..................................... 55 Information displays ..................... 64 Vehicle messages ....
Instruments and controls 51 Horn Press j . Windscreen wiper/washer Windscreen wiper Twist É = fast È = slow Ç = intermittent wiping § = off For a single wipe when the windscreen wiper is off, move the lever up. Do not use if the windscreen is frozen.
52 Instruments and controls Rear window wiper/washer Twist to activate the rear window wiper. Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times.
Instruments and controls 53 Press SET ESC and minutes will flash in the display. Press R or S to adjust. To select 12h or 24h clock, select Mode ; pressing SET ESC will make the display flash. Press R or S to adjust. Press SET ESC briefly to return to the submenu.
54 Instruments and controls Short wheelbase van Long wheelbase van Combi Do not exceed the maximum power consumption of 180 watts. With ignition off, the power outlets are deactivated. Additionally the power outlets are deactivated in the event of low battery voltage.
Instruments and controls 55 Ashtrays Caution To be used only for ash and not for combustible rubbish. The portable ashtray should be placed in the cupholders in the centre console. Warning lights, gauges and indicators Speedometer Indicates vehicle speed.
56 Instruments and controls To reset the trip odometer, press and hold the TRIP button for approx. 2 seconds while the relevant trip odometer is displayed. Tachometer Displays the engine speed. Drive in a low engine speed range for each gear as much as possible.
Instruments and controls 57 Engine coolant temperature gauge Displays the coolant temperature. C = engine operating temperature not yet reached central area = normal operating temperature H = temperature too high If control indicator $ illuminates in conjunction with a message in the information display the coolant temperature is too high.
58 Instruments and controls Control indicators in the instrument cluster.
Instruments and controls 59 Generic warning 9 illuminates yellow. Depending on version control indicator 9 may illuminate independently or in conjunction with Æ , t or r . 9 also illuminates if the fuel cut-off switch is triggered. If 9 illuminates together with I ; stop engine immediately and seek the assistance of a workshop.
60 Instruments and controls With the front passenger airbag deactivated: * permanently illuminates yellow. Airbag deactivation 3 37. 9 Danger Risk of fatal injury for a child using a child restraint system together with activated front passenger airbag.
Instruments and controls 61 Illuminates after the ignition is switched on if the parking brake is applied 3 88. Brake pad wear F illuminates yellow. The front brake pads are worn, seek the assistance of a workshop immediately. Antilock brake system (ABS) u illuminates yellow.
62 Instruments and controls Flashes The system is actively engaged. Engine output may be reduced and the vehicle may be braked automatically to a small degree. Electronic Stability Program 3 90, Traction Control system (ASR) 3 89. Preheating ! illuminates yellow.
Instruments and controls 63 Depending on model, I may flash in the following ways: ■ for one minute every two hours ■ for three minute cycles with I off for intervals of five seconds This will continue until the engine oil is changed. Seek the assistance of a workshop.
64 Instruments and controls Door open illuminates red. A door or the tailgate is open. Information displays Driver Information Centre The Driver Information Centre (DIC) is located in the instrument cluster between speedometer and tachometer.
Instruments and controls 65 Press the SET ESC button to access the menu and/or go to the next screen or confirm your choice. Hold down the SET ESC button to return to the previous screen. Press the R button to scroll up the screen and the menu options or increase the displayed value.
66 Instruments and controls Trip computer The trip computer provides information on driving data, which is continually recorded and evaluated electronically.
Instruments and controls 67 Distance travelled Displays the distance driven since the last reset. The measurement can be restarted at any time. Average speed The average speed since the last reset is displayed. The measurement can be restarted at any time.
68 Lighting Lighting Exterior lighting ............................ 68 Interior lighting ............................. 71 Exterior lighting Light switch Turn light switch: § = off / daytime running lights 9 = sidelights / headlights Control indicator 8 3 63.
Lighting 69 Headlight range adjustment Manual headlight range adjustment To adapt headlight range to the vehicle load to prevent dazzling: Press À or Á buttons until the required setting is displayed in the Driver Information Centre.
70 Lighting Turn and lane-change signals Lever up = right turn signal Lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated.
Lighting 71 Misted light covers The inside of the light covers may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing.
72 Lighting Rear courtesy lights Centre switch position: automatic interior light. To operate manually when the doors are closed, press the lens on either side. Load compartment lighting Depending on vehicle, the lighting switches on when the rear doors / tailgate or sliding side door is opened.
Climate control 73 Climate control Climate control systems ............... 73 Air vents ....................................... 76 Maintenance ................................ 77 Climate control systems Heating and ventilation system Controls for: ■ Temperature ■ Fan speed ■ Air distribution Heated rear window Ü 3 28.
74 Climate control ■ Open side air vents as required and direct them towards door windows. ■ For simultaneous warming of the foot well, set air distribution control to J .
Climate control 75 Controls for: ■ Temperature ■ Air distribution and menu selection ■ Fan speed AUTO = Automatic mode 4 = air recirculation Ê = demisting and defrosting OFF = switch on/off Heated rear window Ü 3 28. The preselected temperature is automatically regulated.
76 Climate control Air distribution Press R , S and 6 buttons. LED in buttons illuminate. Arrows shown in the display indicate the distribution settings. Cooling The air conditioning system cools and dehumidifies (dries) when outside temperature is above a specific level.
Climate control 77 Side air vents Slide knob to the left to open vent. Direct the flow of air by swivelling the vent. Slide knob to the right to close vent. Fixed air vents Additional air vents are located beneath the windscreen and door windows and in the foot wells.
78 Driving and operating Driving and operating Driving hints ................................. 78 Starting and operating ................. 78 Engine exhaust ............................ 82 Manual transmission .................... 83 Manual transmission automated .
Driving and operating 79 Ignition switch positions STOP = Steering wheel lock released, ignition off MAR = Ignition on, for diesel engine: preheating AVV = Starting Starting the engine Manual transmission: operate clutch. Do not operate the accelerator pedal.
80 Driving and operating Stop-start system The stop-start system helps to save fuel and to reduce the exhaust emissions. When conditions allow, it switches off the engine as soon as the vehicle is at a low speed or at a standstill, e.g. at a traffic light or in a traffic jam.
Driving and operating 81 ■ The stop-start system is not manually deactivated ■ the driver's door is closed or the driver's seat belt is fastened ■ the battery is sufficiently charged a.
82 Driving and operating an uphill slope, turn the front wheels away from the kerb. If the vehicle is on a downhill slope, engage reverse gear. Turn the front wheels towards the kerb. ■ Lock the vehicle. Engine exhaust 9 Danger Engine exhaust gases contain poisonous carbon monoxide, which is colourless and odourless and could be fatal if inhaled.
Driving and operating 83 Caution If the cleaning process is interrupted, there is a risk of provoking severe engine damage. Cleaning takes place quickest at high engine speeds and loads. The control indicator [ extinguishes as soon as the self-cleaning operation is complete.
84 Driving and operating Caution It is not advisable to drive with the hand resting on the selector lever. Manual transmission automated The manual transmission automated (MTA) permits manual (manual mode) or automatic gear shifting (automatic mode), both with automatic clutch control.
Driving and operating 85 Always move the selector lever in the appropriate direction as far as it will go. Upon release, it automatically returns to the centre position. N = Neutral. A/ M = Switch between automatic and manual mode. The transmission display shows AUTO when in automatic mode.
86 Driving and operating Engine braking Automatic mode When driving downhill, the manual transmission automated does not shift into higher gears until a fairly high engine speed has been reached. It shifts down in good time when braking. Manual mode To utilise the engine braking effect, select a lower gear in good time when driving downhill.
Driving and operating 87 Activation Press the E button on the selector lever housing. Control indicator E is shown in the transmission display to indicate activation. Deactivation Eco mode is switched off by: ■ pressing the E button again, ■ switching to manual mode.
88 Driving and operating ABS starts to regulate brake pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even during hard braking. ABS control is made apparent through a pulse in the brake pedal and the noise of the regulation process.
Driving and operating 89 The brakes release automatically as soon as the vehicle begins to accelerate. Ride control systems Traction Control system The Anti-Slip Regulator (ASR) is a component of the Electronic Stability Control system.
90 Driving and operating ASR is reactivated by pressing the ASR OFF button again. ASR is also reactivated the next time the ignition is switched on. Fault ASR will switch off automatically in the event of a fault. Control indicator x will illuminate in the instrument cluster in conjunction with a message in the driver information centre.
Driving and operating 91 Cruise control The cruise control can store and maintain speeds above approx. 20 mph. Deviations from the stored speeds may occur when driving uphill or downhill. Do not use the cruise control if it is not advisable to maintain a constant speed.
92 Driving and operating Object detection systems Parking assist The parking assist makes parking easier by measuring the distance between the vehicle and obstacles, and giving acoustic signals. It is the driver, however, who bears full responsibility for the parking manoeuvre.
Driving and operating 93 Notice The parking assist system automatically detects factory-fitted towing equipment. It is deactivated when the connector is plugged in. The sensor may detect a non- existent object (echo disturbance) caused by external acoustic or mechanical disturbances.
94 Driving and operating Fuel for natural gas operation Use natural gas with a methane content of approx. 78 - 99 %. L-gas (low) has approx. 78 - 87 % and H-gas (high) has approx. 87 - 99 %. Biogas with the same methane content can also be used if it has been chemically prepared and desulphurised.
Driving and operating 95 9 Danger Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this remedied immediately by a workshop. Caution In case of misfuelling, do not switch on ignition.
96 Driving and operating Towing General information Only use towing equipment that has been approved for your vehicle. Vehicles with natural gas engine may require special towing equipment. Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment.
Driving and operating 97 The maximum permissible vertical coupling load (75 kg) is specified on the towing equipment identification plate and in the vehicle documents. Always aim for the maximum load, especially in the case of heavy trailers. The vertical coupling load should never fall below 25 kg.
98 Vehicle care Vehicle care General Information ..................... 98 Vehicle checks ............................. 99 Bulb replacement ....................... 105 Electrical system ........................ 109 Vehicle tools .......................
Vehicle care 99 ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.
100 Vehicle care 9 Danger The ignition system use extremely high voltage. Do not touch. Bonnet Opening Pull the release lever and return it to its original position. Push the safety catch and open the bonnet. Secure the bonnet support. Closing Lower the bonnet and allow it to drop into the catch.
Vehicle care 101 Insert dipstick to the stop on the handle and make half a turn. When the engine oil level has dropped to the MIN mark, top up engine oil. We recommend the use of the same grade of engine oil that was used at last change. The engine oil level must not exceed the MAX mark on the dipstick.
102 Vehicle care If the cooling system is cold, the coolant level should be between the MIN and MAX mark. Top up if the level is low. 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. To top up use a 1:1 mixture of released coolant concentrate mixed with clean tap water.
Vehicle care 103 Brakes A squealing noise, or illumination of brake pad wear control indicator F indicates that the brake lining is at its minimum thickness. Continued driving is possible but have the brake linings replaced as soon as possible. Once new brake linings are installed, do not brake unnecessarily hard for the first few journeys.
104 Vehicle care Replacing the battery Notice Any deviation from the instructions given in this paragraph may lead to a temporary deactivation of the stop- start system. In vehicles with stop-start system, ensure to have the correct battery replaced. We recommend that you have the battery replaced by a workshop.
Vehicle care 105 Wiper blade on tailgate Lift wiper arm, press retaining clips to detach wiper blade. Attach the wiper blade to the wiper arm and push until it engages. Lower wiper arm carefully. Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors.
106 Vehicle care 5. Attach connector to bulb. 6. Engage wire clip. 7. Install protective cover. High beam 1. Remove protective cover. 2. Detach connector from bulb. 3. Disengage wire clip and remove bulb from reflector. 4. Insert new bulb in reflector so that the bulb aligns with the reflector recess.
Vehicle care 107 2. Withdraw bulb holder from reflector by turning anticlockwise. 3. Push bulb into holder slightly, rotate anticlockwise, remove and renew bulb. 4. Insert bulb holder in reflector. 5. Rotate clockwise to engage. 6. Install protective cover.
108 Vehicle care Brake light ( 1 ) Turn signal light ( 2 ) Tail light ( 3 ) Tail light/fog light ( 4 ) 7. Install seal on bulb holder ensuring it is fitted correctly. Install bulb holder in light housing ensuring that it engages properly. Tighten four retaining screws using a screw driver.
Vehicle care 109 2. Turn the bulb holder anticlockwise to remove from the bulb housing. Remove the bulb by pulling. 3. Replace the bulb. 4. Insert bulb holder in bulb housing and rotate clockwise 5. Install the bulb housing ensuring it engages correctly.
110 Vehicle care Fuse extractor Use a fuse extractor to remove fuses. Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse.
Vehicle care 111 Engine compartment fuse box The fuse box is in the front left of the engine compartment. Disengage the cover, and lift it upwards to remove.
112 Vehicle care Instrument panel fuse box The fuse box is located on the driver's side behind the cover in the instrument panel. No. Circuit F12 Right low beam F13 Left low beam, headlight range.
Vehicle care 113 No. Circuit F53 Instrument panel F94 Power outlet load compartment F95 Cigarette lighter, power outlet F96 Cigarette lighter, power outlet F97 Heated front seat F98 Heated front seat Vehicle tools Tools Van The tools and the vehicle jacking equipment are in the storage area behind the front seat.
114 Vehicle care Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage.
Vehicle care 115 Tyres should be replaced for safety reasons at a tread depth of 2-3 mm (4 mm for winter tyres). The legally permissible minimum tread depth (1.6 mm) has been reached when the tread has worn down as far as one of the tread wear indicators (TWI).
116 Vehicle care Tyre chains Tyre chains are only permitted on the front wheels. Always use fine mesh chains that add no more than 10 mm to the tyre tread and the inboard sides (including chain lock). Do not exceed 30 mph when snow chains are fitted. 9 Warning Damage may lead to tyre blowout.
Vehicle care 117 5. Screw the flexible filler hose onto the tyre valve. 6. The switch on the compressor must be set to J . 7. Connect the compressor plug to the power outlet or cigarette lighter socket. To avoid discharging the battery, we recommend running the engine.
118 Vehicle care If tyre pressure is more than 1.8 bar, set it to the correct value. Repeat the procedure until there is no more loss of pressure. If the tyre pressure has fallen below 1.8 bar, the vehicle must not be used. Seek the assistance of a workshop.
Vehicle care 119 Make the following preparations and observe the following information: ■ Park the vehicle on a level, firm and non-skid surface. The front wheels must be in the straight-ahead position. ■ Apply the parking brake and engage first or reverse gear.
120 Vehicle care 4. Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping. With the jack correctly aligned, rotate until wheel is clear of the ground. 5. Unscrew the wheel nuts. 6.
Vehicle care 121 2. Insert the wheel wrench into the aperture in the load compartment floor. 3. Rotate the wheel wrench to lower the spare wheel to the floor. 4. Withdraw spare wheel from under the vehicle. 5. Unscrew knob 2 and release cable attachment 1 from spare wheel.
122 Vehicle care Have the defective tyre renewed or repaired as soon as possible. Directional tyres Fit directional tyres such that they roll in the direction of travel.
Vehicle care 123 ■ The vehicles must not come into contact with each other during the jump starting process. ■ Apply the parking brake, transmission in neutral. Lead connection order: 1. Connect the red lead to the positive terminal of the booster battery.
124 Vehicle care Towing Towing the vehicle Release the cap by carefully lifting with a screwdriver. To prevent damage it is recommended to place a cloth between the screwdriver and the frame. The towing eye is stowed with the vehicle tools 3 113. Screw in the towing eye as far as it will go until it stops in a horizontal position.
Vehicle care 125 The towing eye is stowed with the vehicle tools 3 113. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or even better a tow bar – to the towing eye. The towing eye must only be used for towing and not for recovering a vehicle.
126 Vehicle care Exterior lights Headlight and other light covers are made of plastic. Do not use any abrasive or caustic agents, do not use an ice scraper, and do not clean them dry. Polishing and waxing Wax the vehicle regularly (at the latest when water no longer beads).
Vehicle care 127 tank and the pressure valves on the vehicle underbody and the bulkhead in the engine compartment. These components must not be treated using chemical cleaners or preservatives. Have components of the natural gas system cleaned by a workshop authorised to carry out maintenance of natural gas vehicles.
128 Service and maintenance Service and maintenance General information ................... 128 Recommended fluids, lubricants and parts ..............
Service and maintenance 129 Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that meet the recommended specifications. Damage resulting from the use of products not in line with these specifications will not be covered by the warranty.
130 Service and maintenance The system is factory filled with coolant designed for excellent corrosion protection and frost protection down to approx. -28 °C.
Technical data 131 Technical data Vehicle identification .................. 131 Vehicle data ............................... 133 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is visible through the windscreen and in the floor on the front passenger side behind a cover.
132 Technical data Information on identification label: 1 = Type approval number 2 = Vehicle Identification Number 3 = Vehicle type identification code 4 = Permissible gross vehicle weight rating in k.
Technical data 133 Vehicle data Engine data Sales designation 1.4 1.4 Engine identifier code 1.4i 1.4CNG Number of cylinders 4 4 Piston displacement [cm 3 ] 1368 1368 Engine power [kW] 70 88 at rpm 60.
134 Technical data Sales designation 1.3 Turbo 1.6 Turbo 2.0 Turbo Engine identifier code 1.3CDTI 1.6CDTI 1) 2.0CDTI Number of cylinders 4 4 4 Piston displacement [cm 3 ] 1248 1598 1956 Engine power [.
Technical data 135 Performance Engine 1.4i 1.4CNG 1.3CDTI 1.6CDTI 3) 2.0CDTI Maximum speed 4) [mph] Manual transmission 100 107 98 95 5) 98 6) / 102 111 Manual Transmission Automated – – – 95 5).
136 Technical data Type Van Combi High roof 1685 2115 / 2125 – Length of load compartment floor [mm] 1820 2170 950 Load compartment width [mm] 1230 1230 1230 Load compartment height [mm] Standard roof 1305 1305 1305 High roof 1455 – – Wheelbase [mm] 2755 3105 2755 Turning circle kerb to kerb [m] 11.
Technical data 137 Capacities Engine oil Engine 14i 1.4CNG 1.3CDTI 1.6CDTI 2.0CDTI including Filter [l] 2.7 2.7 3.2 4.9 4.9 between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 Fuel tank Petrol/diesel, nominal capacity [l] 60 Natural gas CNG, nominal capacity [kg] Petrol, nominal capacity [l] 16.
138 Technical data Tyre pressures Van Comfort with up to 2 people and 100 kg luggage With full load Engine Tyres front rear front rear [ kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) All 185/65 R15 88T 250/2.5 (36) 250/2.5 (36) 230/2.
Technical data 139 Combi Comfort with up to 3 people With full load Engine Tyres front rear front rear [ kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) All 185/65 R15, 250/2.5 (36) 250/2.5 (36) 230/2.3 (33) 280/2.8 (41) 185/65 R15, 250/2.
140 Customer information Customer information Vehicle data recording and privacy ....................................... 140 Vehicle data recording and privacy Event data recorders The vehicle has a number of sophisticated systems that monitor and control several vehicle data.
Customer information 141 In addition, the manufacturer may use the collected or received diagnostic data: ■ for the manufacturer's research needs ■ to make it available for research needs whe.
142 Index A Accessories and vehicle modifications ............................ 98 Adjustable air vents ..................... 76 Airbag and belt tensioners ........... 59 Airbag deactivation ................ 37, 59 Airbag system .......................
143 Doors ...................................... 21, 23 Drain fuel filter ............................. 63 Driver Information Centre ............. 64 Driving characteristics and towing tips ................................ 96 E Electric adjustment ...
144 K Keys ............................................. 18 Keys, locks ................................... 18 L Lashing eyes ............................... 48 Light switch .................................. 68 Load compartment ................ 23, 46 Load compartment cover .
145 T Tachometer ................................. 56 Tailgate ......................................... 23 Tail lights ................................... 107 Three-point seat belt .................... 33 Tools .......................................
146.
An important point after buying a device Vauxhall Combo (2011) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vauxhall Combo (2011) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vauxhall Combo (2011) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vauxhall Combo (2011) you will learn all the available features of the product, as well as information on its operation. The information that you get Vauxhall Combo (2011) will certainly help you make a decision on the purchase.
If you already are a holder of Vauxhall Combo (2011), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vauxhall Combo (2011).
However, one of the most important roles played by the user manual is to help in solving problems with Vauxhall Combo (2011). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vauxhall Combo (2011) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
