Instruction/ maintenance manual of the product 000 to 26 Vanguard Heating
Go to page of 32
Save this manual for future reference. For more information, visit www.desatech.com WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
www.desatech.com 113111-01A 2 WARNING: Improper installation, adjustment, altera- tion, service, or maintenance can cause injury or prop- erty damage. Refer to this manual for correct installation and operational procedures. For assistance or addi- tional information consult a qualified installer, service agency, or the gas supplier.
www.desatech.com 113111-01A 3 SAFETY INFORMATION WARNING: This product con- tains and/or generates chemicals known to the state of California to cause cancer or birth defects, or other reproductive harm. IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, oper- ate, or service this fireplace.
www.desatech.com 113111-01A 4 SAFETY INFORMATION Continued 3. If you smell gas • shut off gas supply • do not try to light any appliance • do not touch any electrical switch; do not use any phone in your building • immediately call your gas supplier from a neighbor ’ s phone.
www.desatech.com 113111-01A 5 PRODUCT FEATURES SAFETY PILOT This fireplace has a pilot with an Oxygen Deple- tion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-free room fireplaces. The ODS/pilot shuts of f the fireplace if there is not enough fresh air .
www.desatech.com 113111-01A 6 ASSEMBLY Continued 5. Reattach screen by placing the notches in the screen frame over the shoulder screws and pushing down. Assembling Hood 1. Locate four black phillips sheet metal screws from the hardware packet. 2. Rotate hood as shown in Figure 3.
www.desatech.com 113111-01A 7 Unusually tight construction is defined as construction where: a. walls and ceilings exposed to the out- side atmosphere have a continuous water vapor retar der with a rating of one perm (6 x 10 -11 kg per pa-sec-m 2 ) or less with openings gasketed or sealed and b.
www.desatech.com 113111-01A 8 A. Rework worksheet, adding the space of an adjoin- ing room. If the extra space provides an uncon- fined space, remove door to adjoining room or add ventilation grills between rooms. See V entilation Air Fr om Inside Building.
www.desatech.com 113111-01A 9 INSTALLATION NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your pri- mary heat source. If you have a central heating system, you may run system’s circulating blower while using heater.
www.desatech.com 113111-01A 10 LOCATING FIREPLACE WARNING: Maintain the minimum clearances shown in Figures 6 and 7. If you can, pro- vide greater clearances from floor, ceiling, and joining wall. Y ou can recess firebox into the wall. Y ou can also position fireplace in the optional cabinet or cor- ner mantels.
www.desatech.com 113111-01A 11 WARNING: Do not allow any combustible materials to over- lap the firebox front facing. IMPORT ANT : Noncombustible materials such as brick, tile, etc. may overlap the front facing, but should never cover any necessary openings like louvered slots.
www.desatech.com 113111-01A 12 WARNING: Never modify or cover the louvered slots on the front of the firebox. WARNING: Use only non- combustible mortar or adhe- sives when overlapping the front facing with noncombustible fac- ing material.
www.desatech.com 113111-01A 13 INSTALLATION Continued Figure 13 - Attaching Wood Base to Floor 1 3 / 4 " Screw Wood Base 10. Attach wood base to floor with two 1 3 / 4 " black screws provided (see Figure 13). If the floor is concrete use anchor method (see Attaching W ood Base to Solid Floor , page 16).
www.desatech.com 113111-01A 14 INSTALLATION Continued Figure 16 - Removing Valve Cover Shield 1 2 Remove Screw Valve Cover Shield Shoulder Screw Branch Support Snap Bushings Bottom Louver Assembly sembly to the outer casing with 4 #10 screws provided (see Figure 17).
www.desatech.com 113111-01A 15 Figure 20 - Installing Blower Bracket Assembly INSTALLATION Continued Figure 18 - Installing Switch Plate to Valve Cover Shield Switch Plate Screw Valve Cover Shield For Built-In Installation WARNING: A licensed elec- trician must connect the wiring harness to electrical supply fol- lowing all local codes.
www.desatech.com 113111-01A 16 Extension Cord Use extension cord if needed. The cord must have a three-prong, grounding plug and a three-hole recep- tacle. Make sure cord is in good shape. It must be heavy enough to carry the current needed. An under- sized cord will cause a drop in line voltage.
www.desatech.com 113111-01A 17 of screen. Discard screws. Lift fireplace screen up and pull out to remove. 2. Remove screws that attach branch support to fireplace (see Figure 24). Carefully lift up branch support and remove from fireplace (see Figure 24).
www.desatech.com 113111-01A 18 Figure 25 - Attaching Flexible Gas Line to Equipment Shutoff Valve Flexible Gas Line from Fireplace Gas Regulator Provided with Fireplace To Fireplace Gas Regulator Equi.
www.desatech.com 113111-01A 19 INSTALLATION Continued Figure 27 - Checking Gas Joints for Propane/LP Gas (Shown with Optional Mantel) Equipment Shutoff Valve Propane/LP Supply Tank Figure 28 - Checkin.
www.desatech.com 113111-01A 20 5. T urn control knob counter clockwise to the PILOT position. Pr ess in control knob for five (5) seconds (see Figur e 29). Note: Y ou may be running this fireplace for the first time after hooking up to gas supply . If so, the contr ol knob may need to be pressed in for 30 seconds or more.
www.desatech.com 113111-01A 21 OPERATING FIREPLACE Continued OPERATING BLOWER This blower has thr ee settings: ON, OFF , and AUTO. In the ON position, the blower will op- erate constantly .
www.desatech.com 113111-01A 22 CLEANING AND MAINTENANCE WARNING: Turn off fireplace and let cool before cleaning. CAUTION: You must keep control areas, burner, and cir- culating air passageways of fire- place clean. Inspect these areas of fireplace before each use.
www.desatech.com 113111-01A 23 TROUBLESHOOTING Note: All troubleshooting items are listed in order of operation. WARNING: Turn off heater and let cool before servicing. Only a qualified service person should service and repair heater. CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot.
www.desatech.com 113111-01A 24 POSSIBLE CAUSE 1 . Control knob not fully pressed in 2. Control knob not pressed in long enough 3. Safety interlock system has been triggered 4. Equipment shutof f valve not fully open 5 . Thermocouple connection loose at control valve 6.
www.desatech.com 113111-01A 25 TROUBLESHOOTING Continued POSSIBLE CAUSE 1. Residues from manufacturing processes 1. T urning control knob to HI po- sition when burner is cold 2. Air in gas line 3. Air passageways on fireplace blocked 4 . Dirty or partially clogged burner orifice 1.
www.desatech.com 113111-01A 26 WARNING: If you smell gas • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone.
www.desatech.com 113111-01A 27 SERVICE HINTS When Gas Pressure Is Too Low • pilot will not stay lit • burner will have delayed ignition • fireplace will not produce specified heat • propane/LP gas supply may be low (propane/ LP only) Y ou may feel your gas pressure is too low .
www.desatech.com 113111-01A 28 ILLUSTRATED PARTS BREAKDOWN MODELS VMH26TPC (Shown) AND VMH26TNC 23 29 40 32 36 38 13 7 8 33 40 11 10 4 7 30 1 3 2 9 17 19 6 22 31 21 41 42 16 15 18 24 28 34 25 27 20 4 .
www.desatech.com 113111-01A 29 PARTS LIST This list contains replaceable parts used in your fireplace. When ordering parts, follow the instructions listed under Replacement Parts on page 27 of this manual. KEY PART NUMBER NO. VMH26TPC VMH26TNC DESCRIPTION QTY.
www.desatech.com 113111-01A 30 ACCESSORIES NOTICE: All accessories may not be available for all fireplace models. Purchase these fireplace accessories from your local dealer . If they cannot supply these accesso- ries call DESA Heating Products’ Sales Depart- ment at 1-866-672-6040 for referral information.
www.desatech.com 113111-01A 31 ACCESSORIES Continued CORNER MANTEL WITH FULL HEARTH BASE Unfinished - GMC63U Finished - GMC64F White Lacquer - GMC65W For all models.
2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004 www.desatech.com LIMITED WARRANTY VENT-FREE COMPACT CLASSIC HEARTH ® FIREPLACE DESA Heating Products warrants this product to be free.
An important point after buying a device Vanguard Heating 000 to 26 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Vanguard Heating 000 to 26 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Vanguard Heating 000 to 26 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Vanguard Heating 000 to 26 you will learn all the available features of the product, as well as information on its operation. The information that you get Vanguard Heating 000 to 26 will certainly help you make a decision on the purchase.
If you already are a holder of Vanguard Heating 000 to 26, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Vanguard Heating 000 to 26.
However, one of the most important roles played by the user manual is to help in solving problems with Vanguard Heating 000 to 26. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Vanguard Heating 000 to 26 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
