Instruction/ maintenance manual of the product 6100 United States Stove
Go to page of 24
USSC 1 Please read this entire manual before installation and use of this appliance. Failure to follow these instructions could result in property damage, bodily injury, or even death. Contact your local building or fire officials about restrictions and installation inspection requirements in your area.
2 USSC T ABLE OF CONTENTS .............................................................................................. 2 SAFETY PRECAUTIONS ........................................................................................... 3 SPECIFICA TIONS .
USSC 3 Safety Precautions IMPORT ANT : Read this entire manual before inst alling and operating this product. Failure to do so may result in property damage, bodily injury , or even death. Proper inst allation of this furnace is crucial for safe and efficient operation.
4 USSC Specifications Heat Output 1 50,000 to 75,000 BTU/hr . Heating Capacity 2 800 - 2,000 sq. f t. Fuel Burn Rate 3 2.0 - 6.0 lbs./hr . Burn Time (lowest setting) 125 hours continuous Hopper Capacity 250 lbs Heating S pecifications Height 47 i n. Width 25-1/2 in.
USSC 5 Fuel Considerations SHELLED CORN (Dry , preferably corn with 1 1% or less moisture content) • • • • • • • Optimum moisture content of corn should be 1 1% or less. Wet corn will rapidly deteriorate furnace component s, reduce efficiency and void all warranties.
6 USSC INST ALLA TION OPTIONS Read this entire manual before you inst all and use your Multi-Fuel Furnace. Failure to follow instructions may result in property damage, bodily injury , or even death! .
USSC 7 Installation CLEARANCES NOTE: Distance on the left -hand side of your Multi-Fuel Furnace is set at 24 inches for suitable access to the control panel and for f uel loading.
8 USSC Installation VENTING REQUIREMENTS Inst all vent at clearances specified by the vent manufacturer . Do not connect the pellet vent to a vent serving any other appliance or furnace. Do not inst all a flue damper in the exhaust venting system of this unit.
USSC 9 Installation VENT TERMINA TION CLEARANCES: A ----- Minimum 4-foot clearance below or beside any door or window that opens. B ----- Minimum 1-foot clearance above any door or window that opens. C ----- Minimum 3-foot clearance from any adjacent building.
10 USSC Installation THROUGH THE W ALL INST ALLA TION (RECOMMENDED INST ALLA TION) T o vent the unit through the wall, connect the pipe adapter to the exhaust motor adapter . If the exhaust adapter is at least 18-inches above ground level, a straight section of pellet vent pipe can be used through the wall.
USSC 11 Installation PRIMAR Y FURNACE SECONDAR Y (ADD-ON) FURNACE When installed as a seondary furnace, a Duct Damper must be installed between the air discarge of the Pellet furnace and the primary (Gas, Electric, etc.). Damper must be an electric style damper in order to connect to the multi fuel furnace’s PCB (Printed Circuit Board).
12 USSC Do not operate your furnace with the viewing door open. The auger will not feed fuel under these circumst ances and a safety concern may arise from sp arks or fumes entering the room. A working smoke detector must be inst alled in the same room as this product.
USSC 13 Heat Range Room Fan Draf t Fan Aux. Auto Manual CONTROL PANEL T urning the furnace OFF/ON, as well as adjustments for the fuel feed rate and room fan speed are performed by pressing the appropriate button(s) on the control panel which is located on the lower lef t-hand side of your American Harvest furnace.
14 USSC SHUT DOWN PROCEDURE Press the “OFF” button on the control panel to put the furnace in shut down mode. At this time, the red light above the “OFF” button will illuminate. Once this is done, the auger will stop feeding fuel, but the room air blower(s) and draf t fan will continue to operate.
USSC 15 Maintenance Operation DAIL Y OPERA TION The hopper and furnace top will be hot during operation; therefore, you should always use some type of hand protection when refueling your furnace. Never place your hand near the auger while the furnace is in operation.
16 USSC INTERIOR CHAMBERS Remove the two(2) cleanout plates on each side of the damper control. Using the cleaning tools provided, clean all ash and fue l matter from the burn chamber . This may need to be done daily depending on fuel consumption. Periodically remove and clean the burnpot and the area inside the burnpot housing.
USSC 17 Parts Diagram.
18 USSC Parts List 1 5 9 8 10 12 7 4 6 11 3 2 Item Part No. T itle Qty . 1 25507 Feed Door 1 2 25492 Handle, Door 1 3 83506 3/8 x 1 1/4 Roll Pin 1 4 891053 Door Glass w/o Logo 1 5 88066 5/8” Rope Gasket 4.5 f t 6 88087 Glass Gasket (1 x 1 3/16) 3 ft 7 25520 Bottom Glass Ret ainer 1 8 25521 T op Glass Ret ainer 1 P ARTS LIST Item Part No.
USSC 19 Wiring Diagram.
20 USSC T rouble Shooting PROBLEM CAUSE: Not enough combustion air; Fuel has to much moisture. V iewing window becoming black shortly after start-up. • Adjust the air damper to a more open position. • Use a fuel with less moisture content PROBLEM CAUSE: Not enough combustion air; Fuel has to much moisture.
USSC 21 Error Codes Below is a chart describing the Error Codes that might be displayed if your unit has the T ype B controller . Error Code Err1 Err2 Err3 Err4 Err5 Err6 Err7 Err8 Error Descrption The high limit temperature sensor has tripped. Furnace ran out of fuel during normal operation.
22 USSC Notes.
USSC 23 Notes.
24 USSC THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM YOUR KING OR ASHLEY, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE. WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON THE NAMEPLATE ATTACHED TO THE HEATER.
An important point after buying a device United States Stove 6100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought United States Stove 6100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data United States Stove 6100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, United States Stove 6100 you will learn all the available features of the product, as well as information on its operation. The information that you get United States Stove 6100 will certainly help you make a decision on the purchase.
If you already are a holder of United States Stove 6100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime United States Stove 6100.
However, one of the most important roles played by the user manual is to help in solving problems with United States Stove 6100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device United States Stove 6100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
