Instruction/ maintenance manual of the product 810e Uniden
Go to page of 10
uni en@ PRO 810e Professional CB Base Station OWNER'S MANUAL -- ----..--.
l .--.... Welcome! To the world of sophisticated, microprocessor controlled CB radio communi- cations. Your Uniden PRO 81 Oe represents the most advanced base station ever designed for use in the Citizens Band Radio SeNice. It will operate on anyofthe 40 AM, 40 usa, and 40 LSB frequencies authorized by the Department of Communi- cations.
I~ .", -. Installation Select a location that is convenient for operation and allows adequate air circula- tion around the unit. Do not place anything directly on top of the radio cabinet which would block the cooling vents. Avoid areas of high heat.
1. Microphone - The operational mode of the CB is controlled by the push-to- talk switch on the mic. Press the switch to activate the transmitter and disable the receiver. Release the switch to enable the receiver and disable the transmitter. When transmitting, hold the mic about 2 inches from your mouth and speak clear- ly in a normal voice.
r .... _. 0 eration Connecting the Power Plug the power cord into any 240 VAC outlet. Make sure the cord is not kinked or tightly wound. To Receive 1. Be sure that the power source, antenna and microphone are properly connect- ed. 2. Turn the unit on by rotating the Volume control clockwise.
l --'.-. -"- Troubleshootin If your PRO 81 De is not performing up to your expectations, please try these simple steps: Trouble Check Unit will not turn on. No power. 1. Check power cord and all connections. 2. Check wall switch if any. 3. Check house electrical system.
<::. -==:: -~ i- S ecifications Channels: Frequency Range: Frequency Control: Frequency Tolerance: Operating Temp.: Microphone: Input Voltage: Current Drain: 40 AM, 40 usa, 40 LSB 26.965 to 27.405 MHz Phase Locked Loop (PLL) synthesizer ::!: 0.005% - 30°C to + 50°C Plug in type: dynamic 240V AC 50 Hz TX:full mod.
l - Channel Fre uencies NOTE: This radio has been designed to operate in the 11 meter Citizens Radio Se Nice. It uses a frequency synthesizing circuit with Phase Locked Loop (PLLJ tech- niques to provide crystal controlled transmit and receive operation on all 40 chan- nels.
l Warran WARRANTOR: Uniden Australia Pty. Ltd. ("UN/DEN"). ELEMENTS OF WARRANTY: Uniden warrants, for the duration of this warran- ty, UN/DEN CBProduct (hereinafter referred to as the Product) to be free from de- fects in materials and craftsmanship with only the limitations or exclusions set out below.
~ I ~ 1 '-'-'" ~~~- .~ uniden@ -==== -. 0_- AUSTRALIA PTY. LTD. 345 Princes Highway, Rockdale, N.S.W. 22 J 6 Phone: (02) 599 3355 Fax: (02) 599 40 J 8 UTUAO I 552CA -, - ." "'--- --n.-- -" Printed in the Philippines .
An important point after buying a device Uniden 810e (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Uniden 810e yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Uniden 810e - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Uniden 810e you will learn all the available features of the product, as well as information on its operation. The information that you get Uniden 810e will certainly help you make a decision on the purchase.
If you already are a holder of Uniden 810e, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Uniden 810e.
However, one of the most important roles played by the user manual is to help in solving problems with Uniden 810e. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Uniden 810e along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
