Instruction/ maintenance manual of the product MCS-100 Ultra Start
Go to page of 8
Inst allation Manual .
MCS-100 2 Version A SECTION 1 : SYSTEM LAY OUT SECTION 2 : SYSTEM CONNECTI ON Diagram # 1: Tilt Switc h or External Sensor Connec tion You can connect any external trigger devices. Mak e sure negative trigger output of external device is connected to Negative Trigger Input W ire (Green #4).
MCS-100 3 Version A 2. Use 30/40 Am p SPDT relay to connec t as shown. Connect the Starter Interrupt output (Orange) wire to pin 86 of the relay . Connect pin 30 of the relay to the Motor side of the Starter wire. Connect pin 87a of the relay to the switch side of the Starter wire.
MCS-100 4 Version A SECTION 3 : SYSTEM OP ERA TION The MCS-100 is very sophistic ated, but the operation is sim ple. Your two button RF transm itter is easy to use f or arm , disarm , personal protection, and program ming the system f or many custom functions.
MCS-100 5 Version A Shock Sensor Disable Shock Sensor Enable (4.6) Turn ignition on. W ithin 10 seconds , press button #1, #2, #3, #1 in succession. (#3=#1+#2) 1 2 1 2 Valet Mode On Valet Mode Off (4.7) Turn Ignition on. W ithin 10 seconds, press button #2, #3, #2, #3 in succession.
MCS-100 6 Version A 4.4 Emergency Disarm The em ergency disarm is ac tivated through the ignition key s witch and m eans that the system can be disarm ed without rem ote. To activate the EMERGENCY DISARM: While the sys tem is triggered, turn the ignition key on and off four (4) times within ten (10) seconds.
MCS-100 7 Version A 4.7 Valet Mo de The Valet Mode is activated thr ough the igniti on k ey switch and m eans that all normal system f unctions are turned off . This feature is usef ul when v alet park ing, refueling, or servicing y our m otorcycle. To activate the VALET MODE: Turn the ignition key to the on position.
MCS-100 8 Version A 1. Turn the ignition key to the on position. 2. Within ten (10) sec onds PRESS BUTTONS #1, #3, #1, #3 in succession. (#3=#1+#2) 3. The operation is confirmed with one chirp sound and one parking light flash. 4. Press button #1 of your trans mitter to increase the shock s ensor sensitivity.
An important point after buying a device Ultra Start MCS-100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ultra Start MCS-100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ultra Start MCS-100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ultra Start MCS-100 you will learn all the available features of the product, as well as information on its operation. The information that you get Ultra Start MCS-100 will certainly help you make a decision on the purchase.
If you already are a holder of Ultra Start MCS-100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ultra Start MCS-100.
However, one of the most important roles played by the user manual is to help in solving problems with Ultra Start MCS-100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ultra Start MCS-100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
