Instruction/ maintenance manual of the product 430 Series Ultra Start
Go to page of 12
T ec hnical Suppor t 866-698-5872 e xt 0 Suppor t@ultr astar ter s.com FCC/ID Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This devi.
Ta b l e O f C o n t e n t s P a g e 2 Wiring Diagram Page 3 Inst allation T ip s Page 4 Pre-Installation Suggestions Inst allation Suggestions Mounting The Module Installing The LED Installing The Pr.
Blue Connect to hood and / or trunk pin Hood Input Green Connect to door pin. (-) when opened Door Input Purple Connect to door pin. (+) when opened Door Input Black Connect to chassis ground Ground Input Brown Connect to Siren wire. 2amp Maximum Siren Output Red Connect to constant power .
R ecommended Installation Procedur es White (+) Park light s Park light output. Orange (-) When Armed Negative output when system is armed. Grey (-) T runk Release Negative output for trunk release. 500ma max. Y ellow Ignition Input Input from vehicles ignition wire.
10 Pin P ow er Connector Step 2- Plug-In T he Module Step 3- T est And Adjust T he Shock Sensor Y our Basic Install Is Complete! Step 4- T est T he System Step 1 - Connect All Of the F ollo wing W ir es When all the connections are done, the control module can be plugged in.
Program mode allows you to adjust the settings and options of your system. Y our system has been intelligently designed by installers with years of experience.
Entering program mode is done by the following steps: 1) Make sure ignition is in the off position. 2) T urn the ignition key ON - OFF , leaving key in the OFF position. 3) Press and release the V alet button two times. 4) The siren will chirp one time to confirm entering program mode.
T o change settings: 1 - Enter Program Mode - (Ignition ON-OFF , followed by V alet 2 times) 2 - Press & release transmitter buttons in the following sequence #1 - #1 then #3 3 - The siren will re.
- Press and release to arm the alarm and lock the doors. - Press and hold to activate Panic mode. - Press and release to deactivate triggered alarm. - Press and release to disarm and unlock the doors . - Press and hold to activate the T runk Release. - Press and release to deactivate triggered alarm.
1.Press and hold the UNLOCK button for three seconds. 2.The doors will unlock, continue holding the unlock button three seconds. the T runk release will then activate. The trunk release will be confirmed by one park light flash. 3.For safety reasons, the trunk release output will not activate when ignition key is in the “On” po si t i on .
Star ter Disable The system has an optional starter disable output that can be connected by your dealer . When the starter disable relay is installed and connected to the system, the vehicle’ s starter will be disabled when the system is armed. T o activate the st arter disable press the lock button on the remote.
87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 Ne gativ e T ype Door Locks P ositive T ype Door Locks 5 W ir e / Re v er se Polarity T ype Door Locks Ne gativ e P ar k Lights- In some cases the park light s may flash erratically after installing the negative p ark light relay .
An important point after buying a device Ultra Start 430 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ultra Start 430 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ultra Start 430 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ultra Start 430 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Ultra Start 430 Series will certainly help you make a decision on the purchase.
If you already are a holder of Ultra Start 430 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ultra Start 430 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Ultra Start 430 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ultra Start 430 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center