Instruction/ maintenance manual of the product 430 Ultra Start
Go to page of 12
FCC/ID Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
COMPONENTS - Three Button Remote transmitter’s (430 Series) -Control Module - Four Button Remote transmitter ’s (440 Series) - Plug-in Led - Plug-in V alet Switch (Program Switch) - Multi-T one Si.
Blue Connect to hood and / or trunk pin Hood Input Green Connect to door pin. (-) when opened Door Input Purple Connect to door pin. (+) when opened Door Input Black Connect to chassis ground Ground Input Brown Connect to Siren wire. 2amp Maximum Siren Output Red Connect to constant power .
INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 4 Blue Connect to hood and / or trunk pin Hood Input Green Connect to door pin. (-) when opened Door Input Purple Connect to door pin. (+) when opened Door Input Blk/White Dome Light Supervision Output (-) Dome Light Black Connect to chassis ground Ground Input Brown Connect to Siren wire.
REMOTE V EHICLE SECURITY INSTALL MANUAL P AGE 5 Recommended Installa tion Pr ocedures White (+) Park lights Park light output. Orange* (-) When Armed Negative output when system is armed. Grey* (-) T runk Release Negative output for trunk release. Y ellow (+) Ignition Input Input from vehicles ignition wire.
INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 6 Step 3- T est And Adjust The Shock Sensor (see page 3) R ecommended Installation Procedures Basic Install Installing the LED- Choose a location that will be highly visible when the LED is installed.
REMOTE V EHICLE SECURITY INSTALL MANUAL P AGE 7 Changing A Prog rammable Setting Quick View Prog ramming T o Enter Program Mode 1) Make sure ignition is in the off position. 2) Within three seconds turn the key ON the OFF . 3) Press and release the Program Button two times.
INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 8 Enter Program Mode Entering program mode is done by the following steps: 1) Make sure ignition is in the off position. 2) T urn the ignition key ON - OFF , leaving key in the OFF position. 3) Press and release the V alet button two times.
REMOTE V EHICLE SECURITY INSTALL MANUAL P AGE 9 V oltage / Door Pin Sensing 1 - Enter Program Mode - (Ignition ON-OFF , followed by V alet 2 times) 2 - Press & release transmitter buttons in the f.
INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 10 T r ansmitter Progr amming Follow the steps below to program the transmitters to the system s memory Step 1 - T urn the Ignition key ON then OFF - Leaving Key Off. Step 2 - Press and release the Program Button twice then press and hold.
REMOTE V EHICLE SECURITY INSTALL MANUAL P AGE 11 Arm 1. Press and release the button. 2. The park light s will flash and the siren will chirp one time. 3. The doors will lock (optional). NOTE : The LED will start flashing within five seconds. If installed, the starter disable will activate.
87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 Negative Type Door Loc ks Positiv e Type Door Locks 5 Wire / Re verse Polarity Type Door Loc ks Negative Park Lights- In some cases the park lights may flash erratically after installing the negative park light relay .
An important point after buying a device Ultra Start 430 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ultra Start 430 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ultra Start 430 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ultra Start 430 you will learn all the available features of the product, as well as information on its operation. The information that you get Ultra Start 430 will certainly help you make a decision on the purchase.
If you already are a holder of Ultra Start 430, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ultra Start 430.
However, one of the most important roles played by the user manual is to help in solving problems with Ultra Start 430. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ultra Start 430 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
