Instruction/ maintenance manual of the product TB154 Troy-Bilt
Go to page of 28
Operator’ s Manual Electric Gar den Cultivator TB154 SA VE THESE INSTRUCTIONS For service call 1-800-828-5500 in the United States, or 1-800-668-1238 in Canada to obtain a list of authorized service dealers near you. For more details about your unit, visit our website at www.
2 TRAINING • Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Be thoroughly familiar with the controls and the proper use of the cultivator. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.
3 RULES FOR SAFE OPERATION SAFETY AND INTERNATIONAL SYMBOLS This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
4 APPLICATIONS • Cultivating sod and light to medium soil • Cultivating in garden areas, around trees, etc. KNOW YOUR CULTIVATOR Tine Engage Control Tine Shield Tines Overload Protection Switch St.
5 ASSEMBLING THE HANDLEBARS Before you can operate the unit, you must install the handlebars. 1. When you unpack the unit, hold the handle bar in the position shown in Figure 1 and slide it onto the lower bars. 2. Align the holes in the handlebar with the holes in the lower bars and insert the bolts through those holes.
6 USING THE CORD RETAINER There is an extension cord retainer to prevent the extension cord from disconnecting during use. The retainer hangs from the cord guide bar. NOTE: Do not plug the extension cord into the power source receptacle until the cord is connected to the cord retainer and plugged into the unit.
7 STARTING INSTRUCTIONS Connecting to an Electrical Power Source NOTE: Connect your extension cord to the cultivator as instructed on the previous page prior to plugging your extension cord into an electrical outlet. 1. Plug your extension cord into any convenient (indoor or outdoor) 120-volt, 60-cycle AC grounded outlet or receptacle.
8 ADJUSTING THE WHEEL SUPPORT BRACKET To adjust the wheel support bracket, proceed as follows: 1. Remove cotter pin from the clevis pin and slide pin out of tailpiece bracket (Fig. 8). 2. Slide the wheel support bracket up or down in the tailpiece, aligning the holes to the desired height.
9 Fig. 13 REMOVING AND REPLACING TINES Cultivator tines are subject to wear and should be replaced if any signs of damage are present. Tines should also be removed and cleaned after each use. To replace the cultivator's tines: 1. Remove the click pin found at the end of each tine shaft.
10 NOTE: For repairs beyond the minor adjustments listed above, contact your nearest Troy-Bilt Parts & Repair center (1-800-520-5520) or other qualified service dealer for an adjustment.
11 NOTES.
12 NOTES.
13 NOTES.
14 MANUF ACTURER’S LIMITED W ARRANTY FOR: No implied warranty, including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified.
Manual del Operador Cultivadora Eléctrica TB154 CONSERVE EST AS INSTRUCCIONES Llame 1-800-828-5500 en EE.UU. o al 1-800-668-1238 en Canada para obtener una lista de distribuidores de servicio localizados cerca de usted. Para obtener más detalles sobre su unidad, visite nuestro sitio en www.
E2 NORMAS PARA UNA OPERACIÓN SEGURA CAPACITACIÓN • Lea, entienda y cumpla todas las instrucciones incluidas en la máquina y en los manuales antes de montarla y utilizarla. Familiarícese completamente con los controles y con el uso apropiado de la cultivadora.
E3 NORMAS PARA UNA OPERACIÓN SEGURA SÍMBOLOS DE SEGURIDAD E INTERNACIONALES Este manual del operador describe símbolos de seguridad e internacionales, así como pictogramas, que pueden aparecer en este producto. Lea el manual del operador para obtener información completa sobre seguridad, montaje, funcionamiento, mantenimiento y reparaciones.
E4 CONOZCA SU UNIDAD Control de engranado de dientes Pantalla de dientes Dientes Interruptor de protección contra sobrecarga Botón arrancador Barra de control Ruedas Barra de guía del cable Retened.
E5 INSTRUCCIONES DE ENSAMBLE ENSAMBLAJE DE LAS MANIJAS Antes de que pueda operar la unidad, debe instalar las manijas. 1. Cuando desempaque la unidad, sostenga la manija en la posición que se indica en la Figura 1 y deslícela hacia las barras inferiores.
E6 INSTRUCCIONES DE ENSAMBLE Uso del retenedor del cable En la barra de guía del cable situada en la manija superior se haya suspendido un retenedor del prolongador.
E7 INSTRUCCIONES DE ARRANQUE Y APAGADO INSTRUCCIONES DE ARRANQUE Conexión a una fuente de alimentación eléctrica NOTA: Conecte el prolongador a la cultivadora tal y como se indica en la página anterior antes de enchufar el prolongador a una salida eléctrica.
E8 INSTRUCCIONES DE OPERACIÓN AJUSTE DE LA MÉNSULA DE SOPORTE DE LA RUEDA Para ajustar la ménsula de soporte de la rueda proceda de la siguiente manera: 1. Extraiga la chaveta de retén de la chaveta de horquilla y deslice la chaveta hasta extraerla de la ménsula de la pieza posterior (Fig.
E9 INSTRUCCIONES DE OPERACIÓN Fig. 9 EXTRACCIÓN Y REEMPLAZO DE LOS DIENTES Todos los dientes de su cultivadora están sujetos a desgaste, y se deben reemplazar cuando presenten signos de daño. Los dientes también se deben retirar para limpiarlos tras cada uso.
E10 Tipo de motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Eléctrico de 120 V CARPM operativas . . . . . . . . . . . . . . . . . . .
E11 NOTAS.
E12 PARTS LIST REPLACEMENT P AR TS - MODEL TB154 ELECTRIC CUL TIV A TOR.
E13 PARTS LIST REPLACEMENT P AR TS - MODEL TB154 ELECTRIC CUL TIV A TOR Item Part No. Description 1 625-04027A Switch Assembly 2 710-04213 Screw 3 710-0572 Bolt 4 710-0805 Screw 5 912-0324 Nut 6 712-0.
E14 GARANTÍA LIMIT ADA DEL F ABRICANTE P ARA: Ninguna garantía implícita es aplicable, incluyendo cualquier garantía implícita de comerciabilidad o idoneidad para un propósito particular, después del período de la garantía expresa escrita con anterioridad, con respecto a las piezas identificadas.
An important point after buying a device Troy-Bilt TB154 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Troy-Bilt TB154 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Troy-Bilt TB154 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Troy-Bilt TB154 you will learn all the available features of the product, as well as information on its operation. The information that you get Troy-Bilt TB154 will certainly help you make a decision on the purchase.
If you already are a holder of Troy-Bilt TB154, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Troy-Bilt TB154.
However, one of the most important roles played by the user manual is to help in solving problems with Troy-Bilt TB154. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Troy-Bilt TB154 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
