Instruction/ maintenance manual of the product 1250-3000 VA Tripp Lite
Go to page of 20
1 Copyright © 1999 Tripp Lite. All rights reserved. SmartPro ® is a registered trademark of Tripp Lite. 1111 W. 35th Street Chicago, IL 60609 USA Customer Support: (773) 869-1234 www.tripplite.com Owner's Manual Smar tPr o ® NET Smar tPr o ® XL 1250–3000 V A Intelligent Network UPS Systems (120V) ESP AÑOL: p.
Impor tant Saf ety Instructions SA VE THESE INSTRUCTIONS This manual contains important instructions and warnings that should be followed during the installation, operation and storage of all Tripp Lite UPS systems. F ailure to follow these warnings will void your warranty .
3 Installation Plug y our UPS into an electrical outlet. See “Suggested Circuit” in Specifications section to determine if your model should occupy a 20- or 30-amp dedicated circuit. Plug y our equipment into y our UPS. T urn your UPS ON. Set the System Enable Switch (DIP Switch #4, UPS back panel) to the “ENABLE” (UP) position.
4 Switches System Enable Switch (DIP Switch #4) This switch is located in the set of 4 switches next to the UPS’s DB9 ports. It activates the battery charger and intelligent microproces- sor. Always leave it in the “ENABLE” (UP) position when your UPS is plugged in.
5 ON/Standby Switch This momentary switch controls power to the UPS receptacles. Engage it momentarily and release it to toggle between the “ON” mode (power ON at the UPS receptacles) and “Standby” mode (power OFF at the UPS receptacles).
6 This multi-colored light displays 4 separate UPS load conditions. It will turn from green (low) to yellow (medium) to red (high) as you connect equipment to show you the load level your UPS is support- ing. When the light is red your UPS is supporting a load above 85% of its capacity.
7 Specifications Storage & Service Storage Turn your UPS OFF: first, engage the ON/Standby Switch and release it to place your UPS in the “Standby” mode; then set the System Enable Switch (Jumper #4, UPS rear panel) to “DISABLE” (Down); finally, disconnect the UPS power cord from the wall outlet.
Advertencias sobre la ubicación del UPS • Instale el sistema UPS bajo techo, alejado del calor o de la humedad excesi va, de los contaminantes conductiv os, del polvo o de la luz solar directa. • Para un mejor desempeño, mantenga la temperatura interior entre 32º F y 104º F (0º C y 40º C).
9 Conexión #4 (Interruptor "System Enable" o Habilitador Del Sistema) HABILITAR INHABILITAR Instalación Enchuf e el sistema UPS a una toma de energía eléctrica Refiérase a la sección “Especificaciones: Circuito Sugerido” para determinar si este modelo requiere un circuito dedicado o toma directa de 15, 20 ó 30 amperios.
10 3 2 1 Conexión del Puerto DB9 —Opcional—* Usando el cable suministrado por Tripp Lite, conecte el puerto DB9 de su servidor principal de archivos al puerto DB9 rotulado “SMART” (Inteligente), el cual provee comunicaciones completas e inteligentes tipo RS-232.
11 Interruptores Interruptor “System Enable” (Habilitador del Sistema, Conexión No. 4) Este interruptor, uno de los 4 interruptores próximos a los puertos DB9 del sistema UPS, activa el cargador de baterías y el microprocesador inteligente.
12 Esta luz multicolor despliega 7 condiciones diferentes acerca de la carga de la batería del sistema UPS. Se iluminará en rojo (baja), amarillo (mediana) o verde (completa) para indicar el nivel de carga de la batería.
13 el Departamento de Apoyo a Clientes de Tripp Lite para recibir más información y obtener una lista de productos disponibles para administración de redes, conectividad y SMNP. Puertos “BASIC” (Básicos o secundarios) Estos puertos básicos o secundarios conectan el sistema UPS a cualquier estación de trabajo o servidor de archivos.
14 Específicaciones Técnicas SMART 2200 NET SMART 3000 NET Capacidad de Salida (VA/Watts) 2200/1700 3000/2400 Tiempo de Respaldo (Media Carga/Plena Carga) Minutos: 27+/11+ 23+/7+ Tiempo de Recarga de la Batería: 2 - 4 hrs.
Mises en garde relatives à l'emplacement du système UPS • Installez votre système UPS à l'intérieur , à l'abri de l'humidité et de la chaleur excessi ves, des impuretés conductrices, de la poussière et de la lumière directe du soleil.
16 Cavalier #4 (Commutateur de Validation du Systéme) VALIDATION HORS FONCTION Installation Branchez v otre système d’onduleur à une prise c.a. Voyez la section «Suggested Circuit» (Circuit Suggeré) aux «Specifications» (Caractéristiques) pour déterminer si votre modèle exige un circuit dédier de 20 ampères ou de 30 ampères.
17 3 2 1 Connexion du port DB9 –F acultatif–* Utilisant le cablâge Tripp Lite, branchez le port DB9 de votre serveur primaire au port DB9 du système d’onduleur (UPS) marqué «SMART» (qui fournit des communications intelligentes complètes par RS-232).
18 Commutateur s Commutateur de «System Enable» («Système Valide,» Cavalier 4, au panneau d’arrière de l’UPS) Ce commutateur lance le chargeur de batterie et le microprocesseur intelli- gent. Laissez-le toujours sur la position «ENABLE» (la position de «Validation») quand votre UPS est branché.
19 A utres Caractéristiques du Système d’Onduleur Prises CA Les prises fournissent votre équipement connecté d’alimentation de ligne c.a. pendant l’opération normale; elles fournissent votre équipement connecté d’alimentation par batterie pendant les coupures de courant et les baisses de tension.
20 Caractéristiques 93-1310 (9811198) 0699 ATTENTION: CONTAINS SEALED LEAD ACID BATTERY. Must be recycled or disposed of properly. Refer to your local codes for proper disposal or call 1-800-SAV-LEAD for more information.
An important point after buying a device Tripp Lite 1250-3000 VA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tripp Lite 1250-3000 VA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tripp Lite 1250-3000 VA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tripp Lite 1250-3000 VA you will learn all the available features of the product, as well as information on its operation. The information that you get Tripp Lite 1250-3000 VA will certainly help you make a decision on the purchase.
If you already are a holder of Tripp Lite 1250-3000 VA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tripp Lite 1250-3000 VA.
However, one of the most important roles played by the user manual is to help in solving problems with Tripp Lite 1250-3000 VA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tripp Lite 1250-3000 VA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
