Instruction/ maintenance manual of the product PD310 Acer
Go to page of 26
1 English Usage Notice Precautions ........................................................................................... 2 Introduction Product Features ................................................................................... 3 Package Overview .
2 English Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the display housing.
3 English Product Features This product is a SVGA single chip 0.7” DLP Projector. The outstanding features of it are listed as follows: True SVGA, 800 x 600 addressable pixels 3.
4 English Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if anything is missing.
5 English Product Overview Speaker Focus Ring Remote Control Receiver Zoom Ring Zoom Lens Power Connector Elevator Button Connection Ports HDTV/Component Video & Computer Input Connector S-video I.
6 English Remote Control Source Resync Reset Freeze Keystone Correction Power / Standby Volume ( + / - ) Mute Four Directional Select Keys Enter Menu Zoom In / Zoom Out.
7 English Connecting the Projector Installation To ensure the projector works well with your computer, please configure the display mode of your graphic card to make it less than or equal to 800 X 600 resolution. Make sure timimg of the display mode is compatible with the projector.
8 English Powering On the Projector 1 . Remove the lens cap. 2 . Ensure that the power cord and signal cable are securely connected. 3 . The “Power/Standby” indicator will flash. And press the “Power/Standby” button again to start on your projector.
9 English Powering Off the Projector 1. Press the “Power/Standby” button to turn off the projector lamp. 2. After pressing the “Power/Standby” button, you will see a message “Power off the lamp?” on the on-screen display. Press the “Power/Standby” button again to confirm.
10 English Adjusting the Projected Image Adjusting the Projector Height The projector is equipped with an elevator foot for adjusting the projector height. To raise the projector: 1 . Press the elevator button . 2. Raise the projector to the desired display angle , then release the button to lock the elevator foot into position.
11 English . x a M " 5 2 " 8 9 " 3 2 1 " 7 9 1 " 6 4 2 " 0 0 3 . n i M" 0 2" 2 8" 2 0 1" 3 6 1" 4 0 2" 5 4 2 ) H x W ( . x a M " 0 . 5 1 x " 0 . 0 2 " 8 . 8 5 x " 4 . 8 7 " 8 .
12 English Panel Control & Remote Control There are two ways for you to control the function: Remote Control and Panel Control. User Controls Power / Standby 4 Refer to the “Power On/Off the Projector” section on page 8~9. Source 4 Press “Source” to choose RGB, Digital RGB, S-Video and Composite sources.
13 English Use the Panel Control 4 Automatically synchronizes the projector to the input source, when you press this button while the OSD isn’t displayed. Four Directional Select Keys 4 Use or to select items. Use or to make adjustments for your selection.
14 English 4 The Projector has a multilingual On-Screen Display(OSD) menus that allow you to make image adjustments and change a variety of settings. In computer source, the OSD will be the “Computer OSD”. In video source, the OSD will be the “ Video OSD”.
15 English 4 Brightness Adjusting the brightness of the image. Press the to darken the image. Press the to lighten the image. 4 Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.
16 English 4 Brightness Adjusting the brightness of the image. Press the to darken the image. Press the to lighten the image. 4 Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.
17 English 4 Frequency “Frequency” is for changing the display data frequency to match the frequency of your computer’s graphic card. When you experience a vertical flickering bar, use this function to make an adjustment. Tracking Choose “ Tracking” item to synchronize the signal timing of the display with that of the graphic card.
18 English Audio Image-I Image-II Language Management Keystone 16:9 / 4:3 Color Temp. Reset Yes No Video mode Image-II (Video mode) 4 Keystone Correction Adjust image distortion caused by tilting the projector. (±16 degrees) 16 : 9 / 4 : 3 You can select this function to fit your desired aspect ratio type.
19 English 4 Volume Press the to decrease the volume. Press the to increase the volume. 4 Treble The treble setting controls the higher frequencies of your audio source. Press the to decrease the treble. Press the to increase the treble.
20 English 4 Menu Location Choose the Menu location on the display screen. 4 Projection Front-Desktop The factory default setting. Rear-Desktop When you select this function, the projector reverses the image so you can project behind a translucent screen.
21 English Problem: No image appears on screen . 4 Ensure all the cables and power connections are correctly and securely connected as described in the “Installation” section. 4 Ensure the pins of connectors are not crooked or broken. 4 Check if the projection lamp has been securely installed.
22 English 4 If you are using a Notebook PC: 1. You are required to implement above steps of resolution setting of computer first. 2. Switch the Notebook PC display to the “external display only” or “CRT only” mode.
23 English Problem : The screen is outstretched when displaying 16:9 DVD. The projector itself will automatically detect 16:9 DVD and adjust the aspect ratio by digitization to full screen with 4:3 default setting.
24 English Changing the lamp The projector will detect the lamp life itself. It will show you a warning message “ Lamp is running out of standard lifetime. Be sure to replace the lamp as soon as possible.” When you see this message, change the lamp as soon as possible.
25 English Specifications Light Valve - Single Chip DLP TM Technology Lamp - 130W User Replaceable P-VIP Lamp Number of Pixels - 800 pixels(H) X 600 lines(V) Displayable Color - 16.7M colors Projection Lens - F2.2~2.4 f=28.51~34.21mm with 1.2 x zoom & focus Projection Screen Size - 20”~300” Diagonal Projection Distance - 3.
26 English Compatibility Modes Mode Resolution V.Frequency (Hz) H.Frequency (kHz) * compression computer image. (ANALOG).
An important point after buying a device Acer PD310 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Acer PD310 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Acer PD310 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Acer PD310 you will learn all the available features of the product, as well as information on its operation. The information that you get Acer PD310 will certainly help you make a decision on the purchase.
If you already are a holder of Acer PD310, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Acer PD310.
However, one of the most important roles played by the user manual is to help in solving problems with Acer PD310. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Acer PD310 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
