Instruction/ maintenance manual of the product SSDTF1025-105 Transition Networks
Go to page of 9
Installation . . . . . . . . . . . . . . . . . . . . .3 Operation . . . . . . . . . . . . . . . . . . . . . .9 Cable Specifications . . . . . . . . . . . . .10 Technical Specifications . . . . . . . . . .12 Troubleshooting . . . . . . . . . . . . . . .
2 SSDTF10xx-10x (TX) = transmit (RX) = receive * Typical maximum cable distance. Actual distance is dependent upon the physical characteristics of the network. ** SSDTF1029-105 and -106 are intended to be installed in the same network where one is the local device and the other is the remote device.
4 SSDTF10xx-10x Installation -- Continued Set the loop-back switch Hardware mode: The loop-back switch is located on the front panel of the device and is used for installation and network debugging procedures. To set the switch, use a small flat-blade screwdriver or a similar device (see the drawing to the right).
6 SSDTF10xx-10x Installation -- Continued Settings for T1 configuration (right switch set, SW 1) T1/long-haul signal Use switches 3 and 4 on the left switch set to select T1/long-haul signal (see the drawing below). Use switches 1 and 2 on the right switch set to select the proper network cable settings.
8 SSDTF10xx-10x Installation -- Continued Install the copper cable 1. Locate or build twisted-pair copper cables that are compliant with the specifications on page 11 with RJ-45 connectors at both ends. 2. Ensure that the MDI/MDI-X switch is set according to the network conditions (see page 3) .
10 SSDTF10xx-10x Cable Specif ications Fiber cable Single mode fiber (recommended): 9 µm Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140, 85/140, 50/125 µm SSDTF1011-105 850 nm multimode Fiber Optic Transmitter Power: min: -19.
12 SSDTF10xx-10x T echnical Specifications For use with Transition Networks Model SSDTF10xx-10x or equivalent Standards: Emissions: CISPR A; Telecordia TR-NWT-001089 (designed to meet; NOT tested) ; F.
14 SSDTF10xx-10x 4. Is data transfer failing? YES • Verify the local copper connection by starting a local copper loop-back (hardware mode: set the loop-back switch on the local device to “CL”, software mode: enter the local copper loop-back command) and then use a bit error test unit to run a bit error test.
Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules.
An important point after buying a device Transition Networks SSDTF1025-105 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Transition Networks SSDTF1025-105 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Transition Networks SSDTF1025-105 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Transition Networks SSDTF1025-105 you will learn all the available features of the product, as well as information on its operation. The information that you get Transition Networks SSDTF1025-105 will certainly help you make a decision on the purchase.
If you already are a holder of Transition Networks SSDTF1025-105, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Transition Networks SSDTF1025-105.
However, one of the most important roles played by the user manual is to help in solving problems with Transition Networks SSDTF1025-105. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Transition Networks SSDTF1025-105 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
