Instruction/ maintenance manual of the product CSRFB10XX-100 Transition Networks
Go to page of 9
User’ s Guide CSRFB10xx-100 Slide-in-Module Media Converter • Copper to Fiber • 10/100 Bridging (2-Port) • 10Base-T/100Base-TX to 100Base-FX The CSRFB10xx-100, 2-port Ethernet/Fast Ethernet bridging media converter is designed to be installed in a Transition Networks PointSystem™ chassis.
2 CSRFB10xx-100 24-hour Technical Support: 1-200-260-1312 -- International: 00-1-952-941-7600 Installation CAUTION: Wear a grounding converter and observe electrostatic discharge precautions while handling the media converter. Failure to observe this caution could result in damage to or failure of the media converter.
4 CSRFB10xx-100 24-hour Technical Support: 1-200-260-1312 -- International: 00-1-952-941-7600 The Loopback Mode jumper is located on the media converter’s circuit board (labeled ALL= all frames plus errors, Good = Good frames only). See Jumper position to the right.
6 CSRFB10xx-100 24-hour Technical Support: 1-200-260-1312 -- International: 00-1-952-941-7600 Install the fiber cable 1. Locate or build IEEE 803.2 ™ compliant 100Base-FX fiber cable with male, two-stranded TX to RX connectors installed at both ends.
8 CSRFB10xx-100 24-hour Technical Support: 1-200-260-1312 -- International: 00-1-952-941-7600 Far-E nd Device Near-End Device Med ia Conve rter A Media Converter B 2 Origina l fault on fiber lin k Con.
10 CSRFB10xx-100 24-hour Technical Support: 1-200-260-1312 -- International: 00-1-952-941-7600 Operation -- Contin ued Product features - continued Bandwidth allocation Bandwidth allocation feature is available on the Center located SRFB converter only.
12 CSRFB10xx-100 24-hour Technical Support: 1-200-260-1312 -- International: 00-1-952-941-7600 T echnical Specifications For use with Transition Networks Model CSRFB10xx-100 or equivalent. Standards IEEE 802.3 ™ Data Rate: 10 Mbps, 100 Mbps Dimensions 3.
14 CSRFB10xx-100 24-hour Technical Support: 1-200-260-1312 -- International: 00-1-952-941-7600 Installation -- Continued 4. Is remote converter detected? NO • Check for proper connection from the terminal converter to center converter.
16 Trademark notice All trademarks and registered trademarks are the property of their respective owners. Copyright restrictions © 2005 Transition Networks. All rights reserved. No part of this work may be reproduced or used in any form or by any means - graphic, electronic, or mechanical - without written permission from Transition Networks.
An important point after buying a device Transition Networks CSRFB10XX-100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Transition Networks CSRFB10XX-100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Transition Networks CSRFB10XX-100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Transition Networks CSRFB10XX-100 you will learn all the available features of the product, as well as information on its operation. The information that you get Transition Networks CSRFB10XX-100 will certainly help you make a decision on the purchase.
If you already are a holder of Transition Networks CSRFB10XX-100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Transition Networks CSRFB10XX-100.
However, one of the most important roles played by the user manual is to help in solving problems with Transition Networks CSRFB10XX-100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Transition Networks CSRFB10XX-100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
