Instruction/ maintenance manual of the product CGETF10XX-10X Transition Networks
Go to page of 7
User’ s Guide CGETF10xx-10x Slide-in-Module Media Converter • Gigabit Ethernet • Copper to Fiber • 1000Base-T to 1000Base-SX/LX Transition Networks CGETF10xx-10x Gigabit Ethernet media converter connects 1000Base-T shielded or unshielded twisted-pair copper cable to 1000Base-SX or 1000Base-LX, fiber-optic cable.
2 CGETF10xx-10x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Part Number Port One - Copper Port Two - Single Fiber-Optic CGETF1029-105 RJ-45 1000Base-T 100 m (328 ft)* SC, 1000Base-LX, 1310 TX/1550 RX single mode, 20 km (12.
4 CGETF10xx-10x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Installation -- Continued Install the slide-in-module CAUTION: Slots in the PointSystem™ chassis without a slide-in-module installed MUST have a protective plate covering the empty slot for Class A compliance.
6 CGETF10xx-10x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 Oper ation - Continued Link P ass-T hrough The Link Pass-Through feature allows the media converter to monitor both the fiber and copper RX (receive) ports for loss of signal.
Cable Specifications The physical characteristics must meet or exceed IEEE 802.3™ specifications. Fiber Cable Bit Error Rate: <10-9 Single mode fiber (recommended): 9 µm Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140, 85/140, 50/125 µm CGETF1013-105 850 nm multimode Fiber Optic Transmitter Power: min: -10.
10 CGETF10xx-10x 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 T r oubleshooting If the media converter fails, isolate and correct the fault by determining the answers to the following questions and then taking the indicated action: 1 .
Printed in the U.S.A. 33261.J Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
An important point after buying a device Transition Networks CGETF10XX-10X (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Transition Networks CGETF10XX-10X yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Transition Networks CGETF10XX-10X - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Transition Networks CGETF10XX-10X you will learn all the available features of the product, as well as information on its operation. The information that you get Transition Networks CGETF10XX-10X will certainly help you make a decision on the purchase.
If you already are a holder of Transition Networks CGETF10XX-10X, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Transition Networks CGETF10XX-10X.
However, one of the most important roles played by the user manual is to help in solving problems with Transition Networks CGETF10XX-10X. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Transition Networks CGETF10XX-10X along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
