Instruction/ maintenance manual of the product TS0MFLRD6E Transcend
Go to page of 15
USB 2.0 Internal 6-in-1 Card Reader User ’ s Manual P/N TS0MFLRD6E.
T able of Content s Introduction Package Contents ............................................................................................................... .1 Features .............................................................................
1 Introduction Thank you for purchasing T ranscend’s Internal 6-in-1 Card Reader , a small device de- signed for fast, easy data exchange using six types of storag e media: CompactFlash , IBM Microdrive™, SmartMedia , Secure Digital, MultiMediaCard™, and Memory S tick ® / PRO.
2 Driver Inst allation Driver Inst allation for Windows 98SE, Me, and 2000 1. Power on the computer where you will install the Internal 6-in-1 Card Reader and make sure the USB port is enabled and working properly. NOTE: Do not plug your Internal 6-in-1 Card Reader into the USB port at this time.
3 4. The InstallShield Wizard appears. Click Next . 5. Click Finish to complete the driver installation. If using Windows 98SE or Me, the system will ask you to restart Windows. Select the No, I will restart my computer later radio button and click OK .
4 Driver Inst allation for Windows XP , Linux Kernel 2.4 or Later No driver is needed. Turn off the computer and refer to Hardware Setup below to install the Internal 6-in-1 Card Reader into your PC. Hardware Setup 1. Install the Internal 6-in-1 Card Reader into an available 3.
5 R e d W hite Gre en Black T h i c k B l a c k 1 2 3 4 5 10 9 8 7 6 5. If the layout of USB pin-header does not match the default setting of USB connector (shown above), rearrange the color wires of the USB cable as follows: a. Use a needle to raise th e small plastic tab and pull the color wires out of the connector.
6 b. Refer to the pin assignment of USB connector (as below) and to realign the color wires. c. Keep the same side of wire pins facing up and insert them back into th e con- nector. Press the tab down to fully seat the wire pins. I n s e r t 6. Connect the USB con nector of the Internal 6-in-1 Card Reader to the USB pin-header on the motherboard.
7 2. Four Removable Disk drives with newly assigned drive letters appear in My Com- puter. The Internal 6-in-1 Card Reader is ready for use. T o Use with Windows XP 1. Power on the computer. The Found New Hardware status message appears (the first time you power on the computer after installing the Internal 6-in-1 Card Read- er.
8 T o Use with Linux Kernel 2.4 or Later The Internal 6-in-1 Card Reader is a driver-free device for Linux kernel 2.4 or later. Just follow the procedures below to mount and use it. 1. Power on the computer and insert a memory card into the Internal 6-in-1 Card Reader.
9 Boot-up Function The CompactFlash slot of the Internal 6-in-1 Ca rd Reader can be configured as a bootable drive. To enable the Boot-Up function, your motherboard must support USB boot-up de- vices. Upon completion of the appropriate procedure for your BIOS as described below, a CompactFlash card can be used to boot up your computer.
10 T o Boot-up with AMI BIOS 1. Power on your system and follow the on-screen instructions to enter BIOS or the CMOS setup utility. 2. Refer to the owner’s manual of your motherboard for details about the configuration program for your system. 3. Enter the CMOS Setup Utility main page, select Integrated Peripherals and press Enter ”.
11 6. Select Boot Device Select. 7. Select USB RMD-FDD Generic STORAGE DEVICE for the 1st Boot Device , then press ESC . 8. Choose Save & Exit Setup to save the new configuration to CMOS and exit the CMOS Setup program. At SAVE to CMOS and EXIT (Y/ N)? Type Y and press Enter .
12 S pecifications Power supply............................................... DC 5V from USB port Slots for storage media: .............................. Comp actFlash Card T ype I/II IBM Microdrive SmartMedia Card Secure Digital Card MultiMediaCard Memory S tick / PRO Operating T emperature .
Card Reader Limited W arranty “Above and beyond” is the standard we set ourselves for customer service at Transcend. We consistently position ourselves to be significa ntly above the industry norm. It’s all part of our commitment to Customer Satisfaction.
An important point after buying a device Transcend TS0MFLRD6E (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Transcend TS0MFLRD6E yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Transcend TS0MFLRD6E - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Transcend TS0MFLRD6E you will learn all the available features of the product, as well as information on its operation. The information that you get Transcend TS0MFLRD6E will certainly help you make a decision on the purchase.
If you already are a holder of Transcend TS0MFLRD6E, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Transcend TS0MFLRD6E.
However, one of the most important roles played by the user manual is to help in solving problems with Transcend TS0MFLRD6E. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Transcend TS0MFLRD6E along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center