Instruction/ maintenance manual of the product PTZ-900 Trango Systems
Go to page of 9
PTZ-900 ™ 900MHz Spread-Spectrum Digital Wireless Pan/Tilt/Zoom Camera Control Transmission System Installation and Operating Instructions THE LEADER IN WIRELESS VIDEO.
rev E Trango Systems, Inc. 3 Quick-Start Guide 1 Prior to installing the wireless link, verify proper operation of PTZ controller (keyboard) and hard-wired receiver/driver or dome. 2 Determine the bit rate and interface (RS232 or RS485/422) of the hard-wired system.
rev E Trango Systems, Inc. 5 4 PTZ-900 Installation and Operating Instructions 10 To help protect against potential lightning damage use a lightning surge arrester in line with all cabling entering a structure. Important! Power Adapter must be kept dry.
rev E Trango Systems, Inc. 7 6 PTZ-900 Installation and Operating Instructions Installation Make sure that you have tested the PTZ controller and receiver/driver/ dome using a direct connection (with wires) before installing the wire- less link. Also, it is recommended that the wireless link be tested at short range before installing permanently.
rev E Trango Systems, Inc. 9 8 PTZ-900 Installation and Operating Instructions Transmitter Operation Antenna jack. This connector is used to connect an appropriate Trango transmitter antenna. The antennas authorized for use with this unit are the AD900-9-P patch and the AO900-3-P omni.
rev E Trango Systems, Inc. 11 10 PTZ-900 Installation and Operating Instructions Receiver Operation Antenna jack. This connector is used to connect an appropriate Trango receiver antenna. The antenna authorized for use with this unit is the AD900-9 patch.
rev E Trango Systems, Inc. 13 12 PTZ-900 Installation and Operating Instructions munication is established. If a connection is not made within twenty seconds, the unit will exit programming mode and enter normal oper- ating mode. In this event, simply reboot power to the unit and try again.
rev E Trango Systems, Inc. 15 14 PTZ-900 Installation and Operating Instructions Data not received. 9 Verify that a clear line of sight exists between the transmitter and receiver antennas for distances greater than five hundred feet. 9 Check that the transmit and receive PN sequences, data rate, mode, and address are set the same.
rev E Trango Systems, Inc. 17 16 PTZ-900 Installation and Operating Instructions General Material: cast aluminum Finish: platinum powdercoat Size: 4.65 ″ W × 8.8 ″ L × 2.475 ″ D without antenna Weight: 2.65 lb Connectors and Indicators RF Output: SMA-F connector FCC Compliance: The receiver complies with FCC Part 15.
An important point after buying a device Trango Systems PTZ-900 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Trango Systems PTZ-900 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Trango Systems PTZ-900 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Trango Systems PTZ-900 you will learn all the available features of the product, as well as information on its operation. The information that you get Trango Systems PTZ-900 will certainly help you make a decision on the purchase.
If you already are a holder of Trango Systems PTZ-900, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Trango Systems PTZ-900.
However, one of the most important roles played by the user manual is to help in solving problems with Trango Systems PTZ-900. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Trango Systems PTZ-900 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
