Instruction/ maintenance manual of the product Archer D5 TP-Link
Go to page of 127
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router Rev: 1.0.0 1910011021.
COPYRIGHT & TRADEMARKS Specifications are subjec t to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. Other brands and product names are trademarks or registered trademarks of t heir respective holders.
FCC STATEMENT This equipment has been tested and found to comply wi th the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This is a class B product. In a domestic environmen t, this product may cause radio interference, in which case the user may be required to take adequate measure s.
Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interfer ence-causing equipment regulations.
Safety Information When product has power button, the powe r button is one of the way to shut off the product; when there is no power button, the only way to co mpletely shut off power is to disconnect the product or the power adapter from the power source.
TP-LINK TECHNOLOGIES CO., L TD TP-LINK TECHNOLOGIES CO., L TD Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China DECLARA TION OF CONFORMITY For the following equipment: Product Description: AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router Model No.
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Product Overview ................................................................................... 2 1.1 Overview of the Modem Router .
4.7.2 Clients List .......................................................................................................................... 41 4.7.3 Address Reservation ................................................................................
4.13.1 IPv6 Default Gateway ....................................................................................................... 77 4.13.2 IPv6 Static Route ...........................................................................................
4.24 Logout ......................................................................................................................... 111 Appendix A: Specifications ................................................................................. 112 Appendix B: Troubleshooting .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 1 Package Content s The following contents should be found in your package: One Archer D5 AC1200 Wireless Dual Band Giga.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 2 Chapter 1. Product Overview Thank you for choosing the Archer D5 AC1200 Wireless Du al Ba nd Gigabit ADSL2+ Modem Router .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 3 1.2 Main Features Complies with IEEE 802.11ac to provide a wire less data rate of up to 30 0 Mb p s ( 2. 4 GH z) + 867Mbps (5GHz). Four 10/100/1000Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), one RJ11 port.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 4 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The modem router’s LEDs are lo cated on the top panel (View from top to bottom). They indicate the device’s working stat us.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 5 On There is a device connected to this LAN port, or the LAN port is sending or receiving data. (LAN) Off There is no device connected to this LAN port. On Wireless is enabled.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 6 1.3.2 The Back Panel Figure 1-2 ADSL : Through the port, you can connect the tel ephone to the modem router. Or you can connect them by an external separate sp litter. For details, please refer to 2.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 7 Chapter 2. Connecting the Modem Router 2.1 System Requirement s Broadband Internet Access Service (DSL/Cable/Ethernet). PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 8 Figure 2-1.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 9 Chapter 3. Quick Inst allation Guide This chapter will show you how to configure the basic functi ons of your Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router using Quick Setup Wizard within minutes.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 10 The LEDs of LAN port which you link to the device and the LEDs on y our PC's adapter should be lit. 2) Is the TCP/IP configuration for y our PC correct? If the modem router's IP addre ss is 192.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 11 Note: 1) Do not mix up the user na me and password with your ADSL account user name and password which are needed for PPP connections. 2) If the above screen does not pop up, it means that your Web-br owser has been set to a proxy.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 12 5. Select Yes and wait for 1-2 minutes to detect the connection type. Figure 3-6 Note: If the connection type can not be detected, please select No… and click Next to configure it manually (shown in Figure 3-7 ).
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 13 Note: If you are using the modem router on a new DSL li ne and have not completed your DSL provider ’s online registration, you may be using a generic username and pa ssword.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 14 Figure 3-11 8. On this page, please confirm all parameters. Click Back to modify or click the Save button to save your configuration. Figure 3-12 9. You will see the Complete screen below, click Finish to complete these settings.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 15 Figure 3-13 The basic settings for your modem router are co mpleted. Please open the web browser and try to log on to http://www.tp-link.com to test your Internet connection.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 16 Chapter 4. Configuring the Modem Router This chapter will show confi guration for the key functions on the Web-based management page. 4.1 Login After your successful login, you will see the twent y-three main menus on the left of the Web-based utility.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 17 4.2 S t atus Choose “ Status ”, you can see the corre sponding information about Device Information , DSL , WAN , LAN and Wireless .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 18 Figure 4-1.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 19 4.3 Quick Setup Please refer to 3.2 Quick Installation Guide . 4.4 Operation Mode Choose “ Operation Mode ”, and you will see the screen as shown in Figure 4-2 . Select your desired mode and then click Save .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 20 4.5.1 WAN Settings Choose “ Netw ork ” “ WAN Settings ”, and you will see the WAN Port Information Table in the screen similar to Figure 4-3 .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 21 Figure 4-4 4.5.1.1 Static IP Select this option if your ISP prov ides static IP information to yo u. You should set static IP address, IP subnet mask, and gateway address in the screen below.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 22 Figure 4-5 ATM Configuration: VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid r ange is from 0 to 255. Please input the value provided by your ISP.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 23 Gateway (Optional): Enter the gateway IP addres s in dotted-decimal notation provided by your ISP. DNS Server/ Secondar y DNS Server: Here you can set DNS Server (at leas t one) manually.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 24 Figure 4-6 Click Advance , advanced selections for WAN Service Setup can be shown. MTU (bytes): . The default MTU (Maximum Transmission Unit) value is 1500 Bytes. Do not change the default value unle ss required by your ISP.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 25 Get IP w ith Unicast: It is disabled b y default. A few ISPs’ DHCP Servers do not support the broadcast applications. When t he modem router cannot get the IP address normally, you can choose this option.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 26 Figure 4-7 PPP Username/Password/Confirm Passw ord : Enter the User Name, Password and Confirm Password provided by your ISP. These fields are case-sensitive. Alw ays on: The connection can be re-e stablished automatically when it is down.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 27 Enable IPv6: Check this box to enable IPv6. Default Gatew ay: Select a WAN connection from the dr op-down list as the IPv4 default gateway. IPv6 Default Gatewa y: Select a WAN connection from the dr op-down list as the IPv6 default gateway.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 28 Figure 4-8 4.5.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the Connection Type on the screen.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 29 Figure 4-9 IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP. DNS Server/Secondar y DNS Server: Type in your preferred DNS server. Default Gatew ay: Select a WAN Interface from the drop-down list as the IPv4 default gateway.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 30 Note: After you finish the Internet configuration, please click Save to m ake the settings take e ffe ct. 4.5.2 Interface Grouping Choose “ Network ” “ Interface Grouping ”, you can view all the current groups on this page (shown in Figure 4-11 ).
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 31 Figure 4-12 Click Save to make the entry effective immediately 4.5.3 LAN Settings Choose “ Network ” “ LAN Settings ” menu, and you will see the LAN screen (shown in Figure 4-13 ).
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 32 Enable IGMP Snooping: IGMP Snooping is the process of listening to IGMP (Internet Group Management Protocol) network traffic. The feature prevents hosts on a local network from receiving traffic for a multicast group they have not explicitly joined.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 33 2) If DHCPv6 Server is selected, please complete the following parameters. Figure 4-15 Start IPv6 Address: Enter a value for the DHCPv6 server to start with when issuing IPv6 addresses.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 34 4.5.5 MAC Clone Choose menu “ Netw ork ” “ MAC Clone ”, you can configure t he MAC address of the W AN Interface as shown below . The W AN Interface List displays the W AN Interfaces you have c onfigured on the section 4.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 35 L2TP Pass-through: L2TP (Layer Two Tunneling Pr otocol) is the method used to enable Point-to-Point sessions via the Inter net on the Layer Two level. To allow L2TP tunnels to pass through the modem router, click Enable .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 36 Figure 4-21 This section will guide you to configure a VPN tun nel between two Archer D5s. The topology is as follows. Archer D 5 Archer D 5 Note: You could also use other VPN Rout ers to set VPN tunnels with Archer D5 .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 37 Figure 4-22 IPSec Connection Name: Enter a name for your VPN. Remote IPSec Gatew ay Address (URL): Enter the destination gatew ay IP address which is the public WAN IP or Domain Name of the re mote VPN server endpoint.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 38 Click Show Advanced Settings and then you can configure the Advanced Settings. We recommend you leave the Advanced Settings as default value. Figure 4-23 Mode: Select Main Mode to con figure the standard negotiation parameters for IKE phase1.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 39 Figure 4-24 Enable IPTV: Check the box to enable IPTV function. VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid r ange is from 0 to 255.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 40 Figure 4-25 Group/ IP Address/ Subnet Mask: Displays group name, IP address and subnet mask. The parameters can be configured on the Interface Groupi ng page and LAN Settings page.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 41 Note: 1) To use the DHCP server func tion of the modem router, you mu st configure all computers on the LAN as "Obtain an IP Address automatically". 2) Y ou have to disable NA T of the WAN connections, or the DHCP Relay may not ta ke effect.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 42 Figure 4-27 MAC Address: The MAC address of the PC for which you want to reserve an IP address. IP Address: The IP address reserved for the PC by the modem router. Status: The status of this entry, either Enabled or Disabled .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 43 Figure 4-29 To add a vendor class: 1. Click the Add New button. Then Figure 4-30 will pop up. 2. Enter parameters for the vendor class. Click the Save button. Figure 4-30 To modify or delete an existing entry: 1.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 44 4.8 Wireless 2.4GHz There are seven subme nus under the Wireless 2.4Ghz menu: Basic Setti ngs , WPS Settings , Wireless Security , Wireless Schedule , Wireless MAC Filtering , Wireless Advanced and Wireless Status .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 45 11g only: Select if all of your wireless clients are 802.11g. 11n only: Select only if all of your wireless clients are 802.11n. 11bg mixed: Select if you are using both 802.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 46 Authentication T ype : This option should be chosen if the key type is WEP(ASCII) or WEP(HEX).
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 47 You can also keep the default WPS Status as Enabled and click the Add device button in Figure 4-32 , then Choose “ Press the button of the ne w device in two minutes ” and click Connect .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 48 Setup process. Step 3: When the WPS LED is on, the client devic e has successfully connected to the modem router. Step 4: Refer back to your client device or its documentation for further instructions.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 49 Encryption: You can select Auto , TKIP or AES as Encryption. Wireless Password: You can enter ASCII characters bet ween 8 and 63 characters or 8 to 64 Hexadecimal characters.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 50 Be sur 4.8.4 configur e the T ask Schedule Key Type: You can select the WEP key length (64-bit, or 128-bit.) for encryption. "Disabled" means this WEP key entry is invalid.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 51 ” Wireless MAC Filtering ”, you can control the wireless 4.8.5 Wireless MAC Filtering Choose menu “ Wireless 2.4GHz ” access by configuring the Wireless MAC Filtering function, shown in Figure 4-37 .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 52 nt to modify. Selected button to make selected entries enabled or disabled. ess 00:1 D:0 F:1 1:2 2:3 3 and the cified by any enabled entries in the list to if there are any entries already.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 53 Figure 4-39 Transmit Power: Here you can specify the transmit power of the modem router. You can select 100%, 50% or 25%. 100% is the default setting and is recommended.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 54 4.8.7 Wireless Status Choose menu “ Wireless 2.4GHz ” ” Wireless Status ”, you can see the MA C Address, Current Status, Received Packets and Sent Packets for each connected wireless station.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 55 Figure 4-41 SSID: Wireless network name. Enter a desired SSI D which is case-sensitive and must not exceed 32 characters. The def ault SSID is TP-LINK_5GHz_ XXXXXX (xx is the last six numbers of MAC address) .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 56 SSID (to be bridged): The SSID of the AP your modem ro uter is going to connect to as a client. You can also use the search f unction to select the SSID to join. BSSID (to be bridged): The BSSID of the AP your modem r outer is going to connect to as a client.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 57 button. b). To add a new device: If the wireless adapter supports Wi-Fi Protected Setup (WPS ), you can establish a wireless connection between wireless adapter and modem router using either Push Button Configuration (PBC) method or PIN method.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 58 Figure 4-44 Step 2: Enter the PIN number from the client devic e in the field on the above WPS screen.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 59 Figure 4-45 Disable Wireless Securit y: If you do not want to use wire less security, check this radio button. But it’s strongly reco mmended to choose one of the below modes to ensure security.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 60 Authentication Type : Authentication Type: You can choose the type for the WPA/WPA2-Personal security on the drop-down list.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 61 Be sur 4.9.4 nfigure the T ask Schedule as e to cli ck the Save button to save your settings on this page. Wireless Schedule Choose menu “ Wireless 5GHz ” “ Wireless Schedule ”, you can co shown below .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 62 Figure 4-47 To filter wireless users by MAC Address, clic k Enable . The default setting is Disabled . MAC Address: The wireless station's MAC address that you want to filter.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 63 3. Click the Save button. Click the Enable/ Disabled Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete the selected entries.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 64 Figure 4-49 Transmit Power: Here you can specify the transmit power of the modem router. You can select 100%, 50% or 25%. 100% is the default setting and is recommended.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 65 Figure 4-50 MAC Address: The connected wireless station's MAC address Current Status: The connected wireless.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 66 Figure 4-51 Guest Network: When enable this function, you c an set wireless parameters for guest network.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 67 Figure 4-52 Guest Network: When enable this function, you c an set wireless parameters for guest network.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 68 4.10.3 Guest Status 2.4GHz Choose menu “ Guest Network ” “ Guest Status 2.4GHz ”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 69 4.11 USB Settings There are six submenus under the USB Settings menu, USB Mass Storage , User Accounts , Storage Sharing , FTP Server , Media Server and Print Server . Click any of them, and you will be able to configure the corresponding function.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 70 when volume is non-shared, you can click the Activate button to share the volume.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 71 Figure 4-57 Server Status: Indicates the Storage Sharing's current status. Anonymous access to all the volumes: This function is enabled by default, so that users can access to all activated volumes without aut hentication.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 72 Figure 4-58 2. Click the Brow se button, and then select the Sele ct Volume from the drop-down list. 3. Enter the display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 73 Figure 4-59 Server Status: Indicates the FTP Server's current status. Internet Access: If Internet Access is enabled, user(s) in public network can access FTP server via Internet Address.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 74 Figure 4-60 2. Click the Brow se button, and then select the Sele ct Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 75 b) Enter the name of the share folder in Share Name field. c) Click the Apply button to apply the configuration. Figure 4-62 Click the Scan now to scan all the share folders imm ediately.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 76 4.12.1 Default Gate way Choose “ Route Settings ” “ Default Gatewa y ”, you can see the Default Gateway screen. You can select a WAN Interface from the drop-down list as the system default gateway.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 77 static route. Subnet Mask: It determines which portion of an IP Address is the network portion, an d which portion is the host portion. Gateway: Type in the correct gateway addr ess for the static route.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 78 Figure 4-68 Click the Add Interface button, you can add WAN Interfaces. Click the Save button to save your settings. 4.13.2 IPv6 Static Route Choose “ IPv6 Route Settings ” “ IPv6 Static Route ”.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 79 Prefix Length: The prefix length of the destination IPv6 address. Gateway: Type in the correct IPv6 Gateway addr ess for the IPv6 Static Route. Interface: Select the Interface from the drop-down list.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 80 IP Address : The IP address of the PC running the service application. Protocol : The protocol used for this application. The options are TCP , UDP , or All (all protocols supported by the modem router).
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 81 System Tools –> Manage Control page to be any other value except 80 such as 8080.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 82 Figure 4-74 Interface : Display the default gateway you have set in 4.5.1 WAN Settings . Trigger Port : The port for outgoing traffic. An outgoing connection using this port will trigger this rule.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 83 Note: 1. When the trigger connecti on is released, the correspondi ng opened ports will be closed. 2. Each rule can only be used by on e host on the LAN at a time. The tr igger connection of other hosts on the LAN will be refused.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 84 Current UPnP Status: UPnP can be enabled or di sabled by clicking the Enable or Disable button. This feature is enabled by default. Current UPnP Settings List: This table displays the current UPnP information.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 85 Figure 4-77 Enable Parental Control: Check the box if you want this func tion to take effect.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 86 4.16 Firewall There are four submenus under the Fi rewall menu: Rule , LAN Host , WAN Host and Schedule . Click any of them, and you will be able to configure the corre sponding function.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 87 The methods to add a new rule: 1. Click the Add New button and the next screen will pop up as shown in Figure 4-79 . 2. Give a name (e.g. Rule_1) for the rule in the Description field.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 88 Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button. 2. In the Mode field, select IP Address or MAC Address.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 89 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In IP Address field, enter the IP address. If you select MAC Address , the screen shown is Figure 4-83 .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 90 Figure 4-85 Description : Here displays the description of the sc hedule and this description is unique. Edit : Here you can modify an existing schedule. To add a new schedule, follo w the steps belo w : 1.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 91 4.17 IPv6 Firewall There are four submenus unde r the I Pv6 Firewall menu: IPv6 Rule , IPv6 LAN Host , IPv6 WAN Host and IPv6 Schedule . Click any of them, and you will be able to configure the corresponding function.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 92 Figure 4-88 2. Give a name (e.g. Rule_1) for the rule in the Descri ption field. 3. Select a host from the IPv6 LAN Host drop-down list or choose “ Add IPv6 LAN Host ”.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 93 Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button, and you will see the screen as shown in Figure 4-90 .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 94 Figure 4-92 2. Create a unique description for the host (e.g. Host_1) in the Description field. 3. Enter an IPv6 address in the IPv6 Address field. 4. Enter the prefix length of the IPv6 address in the Prefix Length field.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 95 Figure 4-94 2. Create a unique description for the schedule ( e.g. Schedule_1) in Description field.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 96 Figure 4-95 Enable: Check the box to enable IPv6 Tunnel function. It is disabled by default. Mechanism: Select a type for IPv6 tunnel from th e drop-down list. DS-Lite, 6RD and 6to4 are supported.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 97 Figure 4-97 WAN Connection: Select a WAN connection from the drop -down list. Only the connected WAN connections can be shown in the drop-down list. Configuration Type: Select a configuration type for th is tunnel.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 98 4.19 Bandwid th Control Choose menu “ Bandwidth Control ”, and then you can configure the Upstream Bandwidth and Downstream Bandwidth in the next screen. T he values you configur e should be less than 1000000Kbps.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 99 Figure 4-100 3. Click the Save button. Click the Enable/ Disable Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete the selected entries.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 100 When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Edit button, and then you will go to the next page. Th is page is used for adding or modifying an IP & MAC Binding entry (shown in Figure 4-102 .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 101 Click the Delete Selected button to delete the selected entries. Click the Refresh button to refresh all items. 4.21 Dynamic DNS Choose menu “ Dynamic DNS ”, and you can configure t he Dynamic DNS function.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 102 Figure 4-105 4.23 System T ools Choose menu “ System Tools ”, and you can see the s ubmenus under the main menu: Sys.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 103 Figure 4-106 Log Type: Select the log type to be displayed. Log Level: Select the log level to be displayed. Refresh: Refresh the page to show the latest log list.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 104 Figure 4-108 Time Zone: Select your local time zone from this drop-down list. Date: Enter your local date in MM/DD/YY into the right blanks. Time: Enter your local time in HH/ MM/SS into the right blanks.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 105 Figure 4-109 Current User Status: Thi s box displays the information about User Ty pe , User Name , Host IP Address and Host MAC Address . Account Management: Here you can set the account user information a bout New User Name and Ne w Pa s s wo r d .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 106 Figure 4-110 CWMP: Select Enable to enable the CWMP function. Inform: If enabled, the information will be in formed to ACS server periodically. Inform Interval: Enter the interval time here.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 107 Figure 4-111 An SNMP Agent is an application running on the modem rout er that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 108 Figure 4-113 Click the Restore button to reset all configuration settings to their default values. The default User Name : admin The default Pass w ord : admin The default Subnet Mask : 255.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 109 want to use. 2) When u pgrade the modem router's firmware, yo u may lose its current configurations, so please write down some of your customized settings before upgrading the firmware.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 110 Figure 4-116 Traffic Status: If it is disabled, the f unction of DoS protection in Security settings will be disabled.The default value is di sabled. To enable it, click the Enable .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 111 Reset Reset the value of the entry to zero. Operation Delete Delete the existing entry in the table. 4.24 Logout Choose “ Logout ”, and you will back to the login screen as shown in Figure 4-117 .
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 112 Appendix A: Sp ecifications General Standards and Protocols ANSI T1.413, ITU G.992.1, ITU G.992.3, ITU G.992.5, IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 113 Appendix B: T roubleshooting T1. How do I restore m y modem router’s configuration to its factor y default settings? With the modem router powered on, press and hold the RESET button on the rear pa nel for 8 to 10 seconds before releasing it.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 114 4 ） Select Obtain an IP address automaticall y and Obtain DNS server address automati cally . Then click OK . For Windows 8 1 ） Move your mouse to the lowe r right corner and you will see Search icon in the Popups.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 115 Now, try to log on to the Web-based configur ation page again after the above settings have been configured.
Archer D5 AC1200 Wir eless Dual Band Gigabit ADSL2+ Modem Router User Guide 116 Appendix C: T echnical Support Technical Support For more troubleshooting he lp, go to: http://www.tp-link.com/e n/support/faq T o do wnload the latest Firmware, Driver , Utility and User Guide, go to: http://www .
An important point after buying a device TP-Link Archer D5 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TP-Link Archer D5 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TP-Link Archer D5 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TP-Link Archer D5 you will learn all the available features of the product, as well as information on its operation. The information that you get TP-Link Archer D5 will certainly help you make a decision on the purchase.
If you already are a holder of TP-Link Archer D5, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TP-Link Archer D5.
However, one of the most important roles played by the user manual is to help in solving problems with TP-Link Archer D5. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TP-Link Archer D5 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
