Instruction/ maintenance manual of the product SD-R5002 Toshiba
Go to page of 18
TOSHIBA AMERICA INFORMA TION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-R5002 D VD REWRITEABLE DRIVE USER MANU AL.
CONTENTS Introductio n .............................................................................. 1 Setup ........................................................................................ 3 Using the D VD Rewr iteable Dr ive ...............
1 INTR ODUCTION – SD-R5002 General Features Reads and record s digital data on DVD-R/-RW and CD-R/-RW discs CD-R/-RW disc write/rewrite at 16X/10X DVD-R/-RW disc write/rewrite at 2X/1X 3-way Disc Ej.
Front Panel Figure 1.SD-R5002 DVD Write able Drive Front Panel Loading Tray Load disc using tray. Busy Light LED The LED lights green or amber whe n the drive is operating (LED is amber whe n drive is writing.) Eject Button The Eject button is used to open the disc tra y so you can install or remove a disc.
3 SETUP – SD-R5002 The following steps must be performe d to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pin s located on the rear of the DVD Rewriteable drive.
4 Placing DVD Rewriteable Drive inside your Computer Now that you have set the jumpers, you are read y to install your DVD Rewriteable drive insid e your computer. Important Note: Disconnect power fr om your co mputer system befo re beginning installation.
5 Power Cable - Connect an internal computer p ower supply cable to the power so cket at the back of the DV D Rewriteable drive. One si de of the plug has chamfered edges, so the power connector fits onl y one way. Push plug completely into the socket making sure the plug fits correctly.
6 Software Driver - Toshiba' s optical drives do not requi re any unique devi ce drivers for Windows '95/'98/2000/Me/XP/NT. After installing your drive and re-booting, your system should recognize your drive.
7 USING THE D VD Rewriteable Drive – SD-R5002 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is moun ted horizont ally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's L oading tra y b y pressing the Eject Button.
8 Figure 2.Inserting Disc Vertically Removing a Disc To remove a disc from the DVD Rewrite able d rive, perform the following steps: 1. Open the Loading T r ay by pressing the Eject Button. 2. Slide disc holders a wa y from disc. 3. Grasp disc by edges , and lift out of loading tra y .
9 Usage Guidelines • K eep the disc tra y closed when not using the D VD Rewriteable Drive . • Do not press do wn on the disc tra y when opening o r closing it. • Do not place objects on the disc tra y . • Ne ve r use a damaged, broken, or d efo r med disc.
10 TR OUBLESHOO TING – SD-R5002 Problem Solution Disc tra y cannot be opened • Check that there is pow er to drive. • Use Emergency Eject instructi ons to open tray . Drive is not recognized by system • Is the drive connected proper ly? Are all cables plugged in proper ly (e.
11 SPECIFICA TIONS –SD-R5002 General Interf ace: A T API Applicable Formats - Write: Write Formats CD-R/RW DVD-R/RW Disc at once, Track at once, session at once, Packet Write, in cremental write, re.
12 Performance Rotational Speed DVD-ROM (single layer) DVD-ROM (dual layer) DVD-R (Ver. 1.0) DVD-R (Ver. 2.0) DVD-RW (Ver 1.1) DVD-video (CSS-Disc) DVD-R (Ver 2.0) (Write) DVD-RW (Ver 1.1) (Write) CD-ROM, CD-R CD-RW CD-DA Transfer CD-DA, Video-CD CD-R (Write) High Speed CD-RW (Write) CD-RW (Write) 7,580rpm (5.
13 Reliability MTBF 100,000 hours P ower ON Hours 5,436 hours/y ear ON/OFF Cycles 313 cycles/y ear Number of Access 600,000 accesses/y ear Operating Duty Cycle 20% of P ower ON time (Reading/Seeki ng) 2% of P ower ON time (Writing/Seeking) MTTR 0.
14 Regulatory The SD-R5002 D VD Wr iteable drive has been ce r tified by the f ollowing regulatory agencies: • UL 1950 • CSA C22.2 No . 950 • TUV (EN60950I) • CE standard • DHHS 21 CFR Sub-C.
15 DRIVE CONNECT ORS –SD-R5002 Figure 1.SD-R5002 DVD Rew riteable Drive Rear Panel - Conne ctors Power Connector Power is supplied to your DVD d rive by the connection with your computer's +5V/+12V power cable to the power socket at the back of drive.
16 Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME PIN NO . I/O SIGNAL NAME HOST SIGNAL NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 .
An important point after buying a device Toshiba SD-R5002 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba SD-R5002 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba SD-R5002 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba SD-R5002 you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba SD-R5002 will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba SD-R5002, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba SD-R5002.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba SD-R5002. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba SD-R5002 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
