Instruction/ maintenance manual of the product BTR2000 Behringer
Go to page of 18
Users manual Version 1.0 April 2005 DEUTSCH RACKTUNER BTR2000.
2 RACKTUNER BTR2000 CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture.
3 RACKTUNER BTR2000 DEUTSCH TABLE OF CONTENTS 1. INTRODUCTION ......................................................................................................... 4 1.1 Before you get started ......................................................
4 RACKTUNER BTR2000 1. INTRODUCTION Thank you for the confidence you have placed in us with your purchase of the BTR2000. You have acquired an extraordinary combination of a tuner and a metronome with integrated rack lighting that also makes it perfect for on-stage use.
5 RACKTUNER BTR2000 DEUTSCH Should your BEHRINGER dealer not be located in your vicinity, you may directly contact one of our subsidiaries. Corresponding contact information is included in the original equipment packaging (Global Contact Information/European Contact Information).
6 RACKTUNER BTR2000 TRANSPOSE/REF [TAP] button. Tuner mode: A short tap on this button lets you use the wheel for transposition (chapter 4.3). Keeping the button pressed longer lets you calibrate the standard A pitch (chapter 4.
7 RACKTUNER BTR2000 DEUTSCH.
8 RACKTUNER BTR2000 + T o enable reference tones and the metronome, click to be output from the MAIN connector , INPUT 2 must be selected and there must be nothing plugged into the SOUND connector! Using the built-in microphone If you want to use the built-in microphone, you must select INPUT 2 and the MUTE button must be pressed.
9 RACKTUNER BTR2000 DEUTSCH 4.1.2 T uning with the built-in microphone + T o be able to work with the built-in microphone, there must be no cable plugged into the INPUT2 connector in the back of the BTR2000 and the MUTE button must be depressed. 1 . Select INPUT 2 with the INPUT switch on the front of the BTR2000.
10 RACKTUNER BTR2000 Bass ( BAS ) This mode is especially well suited for a 6-string bass. (B - E - A - D - G - C) Baritone ( brt ) This setup helps you tune a guitar to a baritone tuning, in which each string is tuned 5 half-tones (a fourth) lower than a normal guitar.
11 RACKTUNER BTR2000 DEUTSCH 4.3.1 Manual calibration The pitch of the standard A is set to a particular frequency using the BTR2000 control panel. 1 . Depress the TRANSPOSE/REF button for at least two seconds. The ¹ 440 LED flashes. The display shows the frequency currently set for the standard A, e.
12 RACKTUNER BTR2000 1 . Briefly press the TRANSPOSE/REF button. The TRANSP light flashes and the display shows the transposition currently set ( 0 , if no transposition is set).
13 RACKTUNER BTR2000 DEUTSCH 5. METRONOME The integrated metronome in the BTR2000 has a range of 30 b eats p er m inute (BPM) to 240 BPM. There are essentially 2 ways to use the metronome: s You can pre-set a tempo (e.g. 60BPM). s The BTR2000 can pick up a tempo set by you.
14 RACKTUNER BTR2000 Acoustic indicator The selected tempo is also output at the SOUND or MAIN connector. + If your instrument is plugged into INPUT 1, the metronome click is output only through the SOUND connector .
15 RACKTUNER BTR2000 DEUTSCH 7. APPLICA TION EXAMPLES The following sample configurations should give you an idea how the BTR2000 can be integrated in a more or less complex environment. If you have only one amplifier available, the setup shown in figure 7.
16 RACKTUNER BTR2000 8. INST ALLA TION 8.1 Rack installation The BTR2000 requires one height unit (1 HU) for installation in a 19" rack. Be certain to leave an additional 10cm free in the back for the connectors. For installation in a rack, M6 machine screws and nuts should be used.
17 RACKTUNER BTR2000 DEUTSCH 9. SPECIFICA TIONS AUDIO CONNECTORS INPUT 1 1/4" TS connector on the front and back Input impedance 1 M Ω , relay hard bypass INPUT 2 1/4" TS connector Input impedance 1 M Ω , buffered SOUND 1/4" TS connector Output impedance 4.
18 RACKTUNER BTR2000 SHORT INSTRUCTIONS.
An important point after buying a device Behringer BTR2000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Behringer BTR2000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Behringer BTR2000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Behringer BTR2000 you will learn all the available features of the product, as well as information on its operation. The information that you get Behringer BTR2000 will certainly help you make a decision on the purchase.
If you already are a holder of Behringer BTR2000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Behringer BTR2000.
However, one of the most important roles played by the user manual is to help in solving problems with Behringer BTR2000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Behringer BTR2000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
